Sorry it was a drafting error Even the nics are up and after binded to Dpdk it is saying
Checking link status...................................................... ....................................done Port 0 Link Down <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<< <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<< Port 1 Link Down <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<< <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<< IPSEC: entering main loop on lcore 0 IPSEC: -- lcoreid=0 portid=0 rxqueueid=0 IPSEC: -- lcoreid=0 portid=1 rxqueueid=0 On Tue, 22 Sep, 2020, 3:55 pm Ananyev, Konstantin, < konstantin.anan...@intel.com> wrote: > > > Hi Anoob and DPDK Dev Team, > > > ------>While we are running the ipsec-secgw application. We are getting > > > following error: > > > > > > IPSEC: No IPv6 SP Inbound rule specified > > > IPSEC: No IPv6 SP Outbound rule specified > > Wonder what makes you think it is an error? > It is just a message saying that you don't have SP rules for IPv6.... > If you don't plan to process ipv6 traffic that is probably ok. > > > > Creating IPv4 Routing Table (RT) context with 1024 max routes > > > LPM: Adding route 192.168.122.0/24 (1) > > > > > > ------>Below are the steps we've performed.. > > > > > > Since we don't have IXGBE driver in the virtual machines. we used > SRIOV to > > > import the IXGBE NIC's (Virtual function) from host(Physical function). > > > We refered the below link for SRIOV: > > > > > > > https://software.intel.com/content/www/us/en/develop/articles/configure-sr-iov-network-virtual-functions-in-linux-kvm.html > > > > > > This the info after importing IXGBE NIC's into virtual machine: > > > -----------> ip link show > > > 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN > mode > > > DEFAULT group default qlen 1000 > > > link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 > > > 2: ens8: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast > state > > > UP mode DEFAULT group default qlen 1000 > > > link/ether 52:54:00:bd:f7:ce brd ff:ff:ff:ff:ff:ff > > > 3: ens9: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast > state > > > UP mode DEFAULT group default qlen 1000 > > > link/ether 52:54:00:e5:35:b5 brd ff:ff:ff:ff:ff:ff > > > 4: ens12: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast > state > > > UP mode DEFAULT group default qlen 1000 > > > link/ether 52:54:00:14:ce:7c brd ff:ff:ff:ff:ff:ff > > > 5: ens13: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast > state > > > UP mode DEFAULT group default qlen 1000 > > > link/ether 52:54:00:d0:73:4c brd ff:ff:ff:ff:ff:ff > > > > > > 6: ens3: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state > DOWN > > > mode DEFAULT group default qlen 1000 > > > link/ether 96:42:49:cd:9c:61 brd ff:ff:ff:ff:ff:ff > > > <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<< > > > 7: ens11: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state > DOWN > > > mode DEFAULT group default qlen 1000 > > > link/ether 3e:f5:92:ef:9e:16 brd ff:ff:ff:ff:ff:ff > > > <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<< > > > > > > > > > 8: ens10: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast > state > > > UP mode DEFAULT group default qlen 1000 > > > link/ether 52:54:00:51:ee:74 brd ff:ff:ff:ff:ff:ff > > > 9: ens14: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast > state > > > UP mode DEFAULT group default qlen 1000 > > > link/ether 52:54:00:da:08:cb brd ff:ff:ff:ff:ff:ff > > > 10: ens15: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast > > > state UP mode DEFAULT group default qlen 1000 > > > link/ether 52:54:00:31:7c:6f brd ff:ff:ff:ff:ff:ff > > > > > > ------>While we are running the ipsec-secgw application. We are getting > > > following error: > > > > > > IPSEC: No IPv6 SP Inbound rule specified > > > IPSEC: No IPv6 SP Outbound rule specified > > > Creating IPv4 Routing Table (RT) context with 1024 max routes > > > LPM: Adding route 192.168.122.0/24 (1) > > > > > > Checking link > > > > > > > status..........................................................................................done > > > Port 0 Link Down > > > > > > > <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<< > > > Port 1 Link Down > > > > > > > <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<< > > > IPSEC: entering main loop on lcore 0 > > > IPSEC: -- lcoreid=0 portid=0 rxqueueid=0 > > > IPSEC: -- lcoreid=0 portid=1 rxqueueid=0 > > > > > > Please find the attachment which contain console logs. > > > > > > Thanks and Regards > > > >
