On Wed, Jan 21, 2015 at 7:19 PM, Bruce Richardson <
bruce.richardson at intel.com> wrote:
> On Tue, Jan 20, 2015 at 11:39:03AM +0100, Martin Weiser wrote:
> > Hi again,
> >
> > I did some further testing and it seems like this issue is linked to
> > jumbo frames. I think a similar issue has already been reported by
> > Prashant Upadhyaya with the subject 'Packet Rx issue with DPDK1.8'.
> > In our application we use the following rxmode port configuration:
> >
> > .mq_mode = ETH_MQ_RX_RSS,
> > .split_hdr_size = 0,
> > .header_split = 0,
> > .hw_ip_checksum = 1,
> > .hw_vlan_filter = 0,
> > .jumbo_frame = 1,
> > .hw_strip_crc = 1,
> > .max_rx_pkt_len = 9000,
> >
> > and the mbuf size is calculated like the following:
> >
> > (2048 + sizeof(struct rte_mbuf) + RTE_PKTMBUF_HEADROOM)
> >
> > This works fine with DPDK 1.7 and jumbo frames are split into buffer
> > chains and can be forwarded on another port without a problem.
> > With DPDK 1.8 and the default configuration (CONFIG_RTE_IXGBE_INC_VECTOR
> > enabled) the application sometimes crashes like described in my first
> > mail and sometimes packet receiving stops with subsequently arriving
> > packets counted as rx errors. When CONFIG_RTE_IXGBE_INC_VECTOR is
> > disabled the packet processing also comes to a halt as soon as jumbo
> > frames arrive with a the slightly different effect that now
> > rte_eth_tx_burst refuses to send any previously received packets.
> >
> > Is there anything special to consider regarding jumbo frames when moving
> > from DPDK 1.7 to 1.8 that we might have missed?
> >
> > Martin
> >
> >
> >
> > On 19.01.15 11:26, Martin Weiser wrote:
> > > Hi everybody,
> > >
> > > we quite recently updated one of our applications to DPDK 1.8.0 and are
> > > now seeing a segmentation fault in ixgbe_rxtx_vec.c:444 after a few
> minutes.
> > > I just did some quick debugging and I only have a very limited
> > > understanding of the code in question but it seems that the 'continue'
> > > in line 445 without increasing 'buf_idx' might cause the problem. In
> one
> > > debugging session when the crash occurred the value of 'buf_idx' was 2
> > > and the value of 'pkt_idx' was 8965.
> > > Any help with this issue would be greatly appreciated. If you need any
> > > further information just let me know.
> > >
> > > Martin
> > >
> > >
> >
> Hi Martin, Prashant,
>
> I've managed to reproduce the issue here and had a look at it. Could you
> both perhaps try the proposed change below and see if it fixes the problem
> for
> you and gives you a working system? If so, I'll submit this as a patch fix
> officially - or go back to the drawing board, if not. :-)
>
> diff --git a/lib/librte_pmd_ixgbe/ixgbe_rxtx_vec.c
> b/lib/librte_pmd_ixgbe/ixgbe_rxtx_vec.c
> index b54cb19..dfaccee 100644
> --- a/lib/librte_pmd_ixgbe/ixgbe_rxtx_vec.c
> +++ b/lib/librte_pmd_ixgbe/ixgbe_rxtx_vec.c
> @@ -402,10 +402,10 @@ reassemble_packets(struct igb_rx_queue *rxq, struct
> rte_mbuf **rx_bufs,
> struct rte_mbuf *pkts[RTE_IXGBE_VPMD_RX_BURST]; /*finished pkts*/
> struct rte_mbuf *start = rxq->pkt_first_seg;
> struct rte_mbuf *end = rxq->pkt_last_seg;
> - unsigned pkt_idx = 0, buf_idx = 0;
> + unsigned pkt_idx, buf_idx;
>
>
> - while (buf_idx < nb_bufs) {
> + for (buf_idx = 0, pkt_idx = 0; buf_idx < nb_bufs; buf_idx++) {
> if (end != NULL) {
> /* processing a split packet */
> end->next = rx_bufs[buf_idx];
> @@ -448,7 +448,6 @@ reassemble_packets(struct igb_rx_queue *rxq, struct
> rte_mbuf **rx_bufs,
> rx_bufs[buf_idx]->data_len += rxq->crc_len;
> rx_bufs[buf_idx]->pkt_len += rxq->crc_len;
> }
> - buf_idx++;
> }
>
> /* save the partial packet for next time */
>
>
> Regards,
> /Bruce
>
> Hi Bruce,
I am afraid your patch did not work for me. In my case I am not trying to
receive jumbo frames but normal frames. They are not received at my
application. Further, your patched function is not getting stimulated in my
usecase.
Regards
-Prashant
