> -----Original Message----- > From: Liu, Jijiang > Sent: Wednesday, January 07, 2015 11:39 AM > To: Ananyev, Konstantin; 'Olivier MATZ' > Cc: dev at dpdk.org > Subject: RE: [dpdk-dev] [PATCH v3 0/3] enhance TX checksum command and csum > forwarding engine > > Hi Konstantin, > > > -----Original Message----- > > From: Ananyev, Konstantin > > Sent: Wednesday, January 7, 2015 5:59 PM > > To: Liu, Jijiang; 'Olivier MATZ' > > Cc: dev at dpdk.org > > Subject: RE: [dpdk-dev] [PATCH v3 0/3] enhance TX checksum command and > > csum forwarding engine > > > > Hi Frank, > > > > > -----Original Message----- > > > From: dev [mailto:dev-bounces at dpdk.org] On Behalf Of Liu, Jijiang > > > Sent: Wednesday, January 07, 2015 2:04 AM > > > To: 'Olivier MATZ' > > > Cc: dev at dpdk.org > > > Subject: Re: [dpdk-dev] [PATCH v3 0/3] enhance TX checksum command and > > > csum forwarding engine > > > > > > Hi Olivier, > > > > > > > -----Original Message----- > > > > From: Olivier MATZ [mailto:olivier.matz at 6wind.com] > > > > Sent: Saturday, December 13, 2014 12:33 AM > > > > To: Liu, Jijiang > > > > Cc: dev at dpdk.org > > > > Subject: Re: [dpdk-dev] [PATCH v3 0/3] enhance TX checksum command > > > > and csum forwarding engine > > > > > > > > Hello, > > > > > > > > On 12/12/2014 04:48 AM, Liu, Jijiang wrote: > > > > > The 'hw/sw' option is used to set/clear the flag of enabling TX > > > > > tunneling packet > > > > checksum hardware offload in testpmd application. > > > > > > > > This is not clear at all. > > > > In your command, there is (hw|sw|none). > > > > Are you talking about inner or outer? > > > > Is this command useful for any kind of packet? > > > > How does it combine with "tx_checksum set outer-ip (hw|sw)"? > > > > > > > > > > I rethink these TX checksum commands in this patch set and agree with > > > you that we should make some changes for having clear meaning for them. > > > > > > There are 3 commands in patch set as follows, 1. tx_checksum set > > > tunnel (hw|sw|none) (port-id) > > > > > > Now I also think the command 1 may confuse user, they probably don't > > > understand why we need 'hw' or 'sw' option and when to use the two > > > option, so I will replace the command with 'tx_checksum set hw-tunnel-mode > > (on|off) (port-id)' command. > > > > I am a bit confused here, could you explain what would be a behaviour for > > 'on' and > > 'off'? > > Konstantin > > I have explained the behaviour for 'on' and'off' below, > > The command 'tx_checksum set hw-tunnel-mode (on|off) (port-id)' is > used to set/clear TESTPMD_TX_OFFLOAD_TUNNEL_CKSUM flag. > > Actually, the PKT_TX_UDP_TUNNEL_PKT offload flag will be set if the > testpmd flag is set, which means to tell HW treat that transmit packet as a > tunneling packet to do checksum offload > When 'on' is set, which is able to meet Method B.1 and method C. > > When 'off' is set, the TESTPMD_TX_OFFLOAD_TUNNEL_CKSUM is not needed > to set, so the PKT_TX_UDP_TUNNEL_PKT offload flag is not needed to set, then > HW treat that transmit packet as a non-tunneling > packet. It is able to meet Method B.2. > > Is the explanation not clear?
Ok, and how I can set method A (testpmd treat all packets as non-tunnelling and never look beyond outer L4 header) then? Konstantin > > > > > > > > > 2. tx_checksum set outer-ip (hw|sw) (port-id) 3. tx_checksum set > > > (ip|udp|tcp|sctp) (hw|sw) (port-id) > > > > > > The command 2 will be merged into command 3, the new command is ' > > > tx_checksum set (outer-ip|ip|udp|tcp|sctp) (hw|sw) (port- id)'. > > > > > > These most of the cases in > > > http://dpdk.org/ml/archives/dev/2014-December/009213.html will be > > > covered by using the two commands > > > > > > The command 'tx_checksum set hw-tunnel-mode (on|off) (port-id)' is > > > used to set/clear TESTPMD_TX_OFFLOAD_TUNNEL_CKSUM flag. > > > Actually, the PKT_TX_UDP_TUNNEL_PKT offload flag will be set if the > > > testpmd flag is set, which tell driver/HW treat that transmit packet as a > > tunneling packet. > > > > > > When 'on' is set, which is able to meet Method B.1 and method C. > > > > > > When 'off' is set, the TESTPMD_TX_OFFLOAD_TUNNEL_CKSUM is not needed > > > to set, so the PKT_TX_UDP_TUNNEL_PKT offload flag is not needed to set, > > > then > > HW treat that transmit packet as a non-tunneling packet. It is able to meet > > Method B.2. > > > > > > As to case A, I think it is not mandatory to cover it in csum fwd engine > > > for > > tunneling packet. > > > > > > Is the above description clear for you? > > > > > > > Regards, > > > > Olivier
