Hi, I'm trying to run l3fwd-power application for 2 Port with queue. Always only queue 1 of port 0 and port 1 are utilized. CPU C-state, hpet are enabled, ports are binded to igb_uio. Tried with NIC's x772 (10 GbE) and XXV710(25 GbE), Observed same behavior.
I am observing the below output: */root/comms/dpdk/examples/l3fwd-power/build/l3fwd-power -l 2,3,4,5 -n 6 --socket-mem 512,0 -w 17:00.0 -w 17:00.1 -- -p 0x3 --config '(0,0,2),(0,1,3),(1,0,4),(1,1,5)' -P* EAL: Detected 48 lcore(s) EAL: Detected 1 NUMA nodes EAL: Multi-process socket /var/run/dpdk/l3fwd/mp_socket EAL: Probing VFIO support... EAL: PCI device 0000:17:00.0 on NUMA socket 0 EAL: probe driver: 8086:158b net_i40e EAL: PCI device 0000:17:00.1 on NUMA socket 0 EAL: probe driver: 8086:158b net_i40e Promiscuous mode selected POWER: Attempting to initialise ACPI cpufreq power management... POWER: Power management governor of lcore 2 has been set to user space successfully POWER: Initialized successfully for lcore 2 power management POWER: Power management governor of lcore 3 has been set to user space successfully POWER: Initialized successfully for lcore 3 power management POWER: Power management governor of lcore 4 has been set to user space successfully POWER: Initialized successfully for lcore 4 power management POWER: Power management governor of lcore 5 has been set to user space successfully POWER: Initialized successfully for lcore 5 power management Initializing port 0 ... Creating queues: nb_rxq=2 nb_txq=4... Port 0 modified RSS hash function based on hardware support,requested:0x20820 configured:0x820 Address:00:E0:ED:96:2B:AA, Allocated mbuf pool on socket 0 Initializing rx queues on lcore 2 ... rxq=0,0,0 Initializing rx queues on lcore 3 ... rxq=0,1,0 Initializing rx queues on lcore 4 ... rxq=1,0,0 Initializing rx queues on lcore 5 ... rxq=1,1,0 Checking link status.....done Port 0 Link Up - speed 25000 Mbps - full-duplex Port 1 Link Up - speed 25000 Mbps - full-duplex L3FWD_POWER: entering main loop on lcore 3 L3FWD_POWER: -- lcoreid=3 portid=0 rxqueueid=1 L3FWD_POWER: entering main loop on lcore 4 L3FWD_POWER: -- lcoreid=4 portid=1 rxqueueid=0 L3FWD_POWER: entering main loop on lcore 5 L3FWD_POWER: -- lcoreid=5 portid=1 rxqueueid=1 EAL: Event already been added. L3FWD_POWER: entering main loop on lcore 2 L3FWD_POWER: -- lcoreid=2 portid=0 rxqueueid=0 EAL: Event already been added. L3FWD_POWER: lcore 3 sleeps until interrupt triggers L3FWD_POWER: lcore 4 sleeps until interrupt triggers L3FWD_POWER: lcore 5 sleeps until interrupt triggers L3FWD_POWER: lcore 2 sleeps until interrupt triggers L3FWD_POWER: lcore 3 is waked up from rx interrupt on port 0 queue 1 L3FWD_POWER: lcore 3 sleeps until interrupt triggers L3FWD_POWER: lcore 5 is waked up from rx interrupt on port 1 queue 1 L3FWD_POWER: lcore 5 sleeps until interrupt triggers I would appreciate it if some expert can shade a light on this. Thanks & Regards, Soumen
