https://bugs.dpdk.org/show_bug.cgi?id=263
Bug ID: 263
Summary: ixgbe does not support 10GBASE-T copper SFP+
Product: DPDK
Version: 17.11
Hardware: x86
OS: Linux
Status: CONFIRMED
Severity: normal
Priority: Normal
Component: ethdev
Assignee: dev@dpdk.org
Reporter: i...@cgstowernetworks.com
Target Milestone: ---
Tried couple of vendor's 10GBASE-T copper SFPs and they fail at init
Transceiver example http://www.eoptolink.com/products/copper-10g-sfp
root@AFS:/home/cgs# ./testpmd -c7 -n3 -w 0000:0a:00.0 -- -i
EAL: Detected 28 lcore(s)
EAL: Detected 2 NUMA nodes
EAL: Multi-process socket /var/run/dpdk/rte/mp_socket
EAL: No available hugepages reported in hugepages-1048576kB
EAL: Probing VFIO support...
EAL: PCI device 0000:0a:00.0 on NUMA socket 0
EAL: probe driver: 8086:10fb net_ixgbe
eth_ixgbe_dev_init(): Unsupported SFP+ Module
eth_ixgbe_dev_init(): Hardware Initialization Failure: -19
EAL: ethdev initialisation failedEAL: Requested device 0000:0a:00.0
cannot be used
testpmd: No probed ethernet devices
Tested in 2 different Intel controllers 82599ES and X552
cgs@AFS:~# lspci -s 0a:00.0
0a:00.0 Ethernet controller: Intel Corporation 82599ES 10-Gigabit
SFI/SFP+ Network Connection (rev 01)
cgs@AFS:~$ lspci -s 04:00.0
04:00.0 Ethernet controller: Intel Corporation Ethernet Connection X552
10 GbE SFP+
If the SFPs is inserted only *after* the dpdk app starts (after rte_eal_init
and pci devices are probed) it will work!
as it is only identified and blocked as not supported in
ixgbe_identify_sfp_module_generic
Though the ixgbe_identify_sfp_module_generic function tries to be premissive in
case the allow_unsupported_sfp is set
if (hw->allow_unsupported_sfp == true) {
EWARN(hw,
"WARNING: Intel (R) Network Connections
are quality tested using Intel (R) Ethernet Optics. "
"Using untested modules is not
supported and may cause unstable operation or damage to the module or the
adapter. "
"Intel Corporation is not responsible
for any harm caused by using untested modules.\n");
status = IXGBE_SUCCESS;
}
but this is too late as this SFP falls into earlier case in the function
/* Verify supported 1G SFP modules */
if (comp_codes_10g == 0 &&
!(hw->phy.sfp_type == ixgbe_sfp_type_1g_cu_core1 ||
hw->phy.sfp_type == ixgbe_sfp_type_1g_cu_core0 ||
hw->phy.sfp_type == ixgbe_sfp_type_1g_lx_core0 ||
hw->phy.sfp_type == ixgbe_sfp_type_1g_lx_core1 ||
hw->phy.sfp_type == ixgbe_sfp_type_1g_sx_core0 ||
hw->phy.sfp_type == ixgbe_sfp_type_1g_sx_core1)) {
hw->phy.type = ixgbe_phy_sfp_unsupported;
status = IXGBE_ERR_SFP_NOT_SUPPORTED;
goto out;
}
The driver reads 0 from eeprom IXGBE_SFF_10GBE_COMP_CODES offset and
comp_codes_10g=0
I guess because there's no 10GBASE-T code defined in SFF-8472 TABLE 5-3
TRANSCEIVER COMPLIANCE CODES [https://members.snia.org/document/dl/25916]
This same 10GBASE-T SFP does work in i40e controllers
see more info and suggested patch in
http://mails.dpdk.org/archives/dev/2019-April/131091.html
--
You are receiving this mail because:
You are the assignee for the bug.
