There is need to eanble 10Mb/s link foixgbe NIC of x553.
This new device has own device id of 0x15E4 and 0x15E5, so
ixgbe PMD driver need to special check when setup link for
these two types of device.
Signed-off-by: Wei Zhao <wei.zh...@intel.com>
---
drivers/net/ixgbe/ixgbe_ethdev.c | 12 +++++++++++-
1 file changed, 11 insertions(+), 1 deletion(-)
diff --git a/drivers/net/ixgbe/ixgbe_ethdev.c b/drivers/net/ixgbe/ixgbe_ethdev.c
index 97e1021..01f3a99 100644
--- a/drivers/net/ixgbe/ixgbe_ethdev.c
+++ b/drivers/net/ixgbe/ixgbe_ethdev.c
@@ -2701,6 +2701,9 @@ static int eth_ixgbevf_pci_remove(struct rte_pci_device
*pci_dev)
allowed_speeds = ETH_LINK_SPEED_100M | ETH_LINK_SPEED_1G |
ETH_LINK_SPEED_2_5G | ETH_LINK_SPEED_5G |
ETH_LINK_SPEED_10G;
+ if (hw->device_id == IXGBE_DEV_ID_X550EM_A_1G_T ||
+ hw->device_id == IXGBE_DEV_ID_X550EM_A_1G_T_L)
+ allowed_speeds |= ETH_LINK_SPEED_10M;
break;
default:
allowed_speeds = ETH_LINK_SPEED_100M | ETH_LINK_SPEED_1G |
@@ -2708,6 +2711,7 @@ static int eth_ixgbevf_pci_remove(struct rte_pci_device
*pci_dev)
}
link_speeds = &dev->data->dev_conf.link_speeds;
+ *link_speeds = ETH_LINK_SPEED_10M;
if (*link_speeds & ~allowed_speeds) {
PMD_INIT_LOG(ERR, "Invalid link setting");
goto error;
@@ -2742,6 +2746,8 @@ static int eth_ixgbevf_pci_remove(struct rte_pci_device
*pci_dev)
speed |= IXGBE_LINK_SPEED_1GB_FULL;
if (*link_speeds & ETH_LINK_SPEED_100M)
speed |= IXGBE_LINK_SPEED_100_FULL;
+ if (*link_speeds & ETH_LINK_SPEED_10M)
+ speed |= IXGBE_LINK_SPEED_10_FULL;
}
err = ixgbe_setup_link(hw, speed, link_up);
@@ -4061,8 +4067,12 @@ static int ixgbevf_dev_xstats_get_names(__rte_unused
struct rte_eth_dev *dev,
switch (link_speed) {
default:
case IXGBE_LINK_SPEED_UNKNOWN:
+ if (hw->device_id == IXGBE_DEV_ID_X550EM_A_1G_T ||
+ hw->device_id == IXGBE_DEV_ID_X550EM_A_1G_T_L)
+ link.link_speed = ETH_SPEED_NUM_10M;
+ else
+ link.link_speed = ETH_SPEED_NUM_100M;
link.link_duplex = ETH_LINK_FULL_DUPLEX;
- link.link_speed = ETH_SPEED_NUM_100M;
break;
case IXGBE_LINK_SPEED_100_FULL:
--
1.8.3.1
