Hi Konstantin,
Thanks for your reply…
Yes adding the VLAN to the VF from the kernel side will work, however,
this is a different behaviour than the XL710.
The XL710 will allow all VLANs to pass through once the PMD takes
control of the VF.
The real use case is using this VF interface trough Open vSwitch which
needs to see all packets regardless of the VLAN.
It does not make sense to create 4K VLANs through the kernel to get this
working.
Looking forward to your reply…
Cheers,
Eelco
On 18 Jan 2019, at 12:25, Ananyev, Konstantin wrote:
Hi
It’s been while since I looked at it last time,
but shouldn’t you assign desired vlan tag to the VF first:
ip link set <device> vf <num> vlan <num>
?
Konstantin
From: Eelco Chaudron [mailto:echau...@redhat.com]
Sent: Thursday, January 3, 2019 4:42 PM
To: Lu, Wenzhuo <wenzhuo...@intel.com>; Ananyev, Konstantin
<konstantin.anan...@intel.com>
Cc: dev <dev@dpdk.org>
Subject: Re: [dpdk-dev] VF of a X520 card does not process VLAN
packets
Hi maintainers, any feedback on the below?
Thanks,
Eelco
On 18 Dec 2018, at 12:06, Eelco Chaudron wrote:
Hi,
I’m assigning a VF of an X520 card for DPDK/testpmd/OVS but it's not
accepting tagged VLAN packets (it does accept tag 0). Is this a known
bug/limitation of the 82599ES chipset?
This is how I've tested it:
$ echo 1 > /sys/bus/pci/devices/0000:05:00.0/sriov_numvfs
$driverctl -v set-override 0000:05:10.0 vfio-pci
$./testpmd -c 7 -n 4 --socket-mem 2048,0 -w 0000:05:10.0 -- \
--burst 64 -i --rxq=1 --txq=1 --rxd=4096 --txd=1024 \
—coremask=6 --auto-start --port-topology=chained
EAL: Detected 28 lcore(s)
EAL: Detected 1 NUMA nodes
EAL: Multi-process socket /var/run/dpdk/rte/mp_socket
...
testpmd>
I’m sending broadcast ARP packets:
Ethernet II, Src: 04:f4:bc:43:e1:00 (04:f4:bc:43:e1:00), Dst:
ff:ff:ff:ff:ff:ff (ff:ff:ff:ff:ff:ff)
Destination: ff:ff:ff:ff:ff:ff (ff:ff:ff:ff:ff:ff)
Address: ff:ff:ff:ff:ff:ff (ff:ff:ff:ff:ff:ff)
.... ..1. .... .... .... .... = LG bit: Locally administered address
(this is NOT the factory default)
.... ...1 .... .... .... .... = IG bit: Group address
(multicast/broadcast)
Source: 04:f4:bc:43:e1:00 (04:f4:bc:43:e1:00)
Address: 04:f4:bc:43:e1:00 (04:f4:bc:43:e1:00)
.... ..0. .... .... .... .... = LG bit: Globally unique address
(factory default)
.... ...0 .... .... .... .... = IG bit: Individual address (unicast)
Type: 802.1Q Virtual LAN (0x8100)
802.1Q Virtual LAN, PRI: 0, CFI: 0, ID: 10
000. .... .... .... = Priority: Best Effort (default) (0)
...0 .... .... .... = CFI: Canonical (0)
.... 0000 0000 1010 = ID: 10
Type: ARP (0x0806)
Padding: 2e2f303132333435363738393a3b
Trailer: 3c3d3e3f404142434445464748494a4b4c4d4e4f50515253...
Address Resolution Protocol (request/gratuitous ARP)
Hardware type: Ethernet (1)
Protocol type: IP (0x0800)
Hardware size: 6
Protocol size: 4
Opcode: request (1)
[Is gratuitous: True]
Sender MAC address: 00:00:00:00:00:00 (00:00:00:00:00:00)
Sender IP address: 0.0.0.0 (0.0.0.0)
Target MAC address: 00:00:00:00:00:00 (00:00:00:00:00:00)
Target IP address: 0.0.0.0 (0.0.0.0)
No traffic is received, if you replace tag 10 with 0, packets are
received.
Note that this is a simple reproducer with testpmd, but it's reported
as part of an OVS integration. This works fine on the physical port,
or with a VF on an XL710 card.
Any input appreciated.
Thanks,
Eelco
