Update the HWRM API to version 1.9.2.53
This is second part of the patch.
Signed-off-by: Ajit Khaparde <ajit.khapa...@broadcom.com>
--
v1->v2:
Update from 1.9.2.45 to version 1.9.2.53
v2->v3:
Split the patch into smaller patches
---
drivers/net/bnxt/hsi_struct_def_dpdk.h | 1153 ++++++++++++++++++++++++
1 file changed, 1153 insertions(+)
diff --git a/drivers/net/bnxt/hsi_struct_def_dpdk.h
b/drivers/net/bnxt/hsi_struct_def_dpdk.h
index a433e6bfd..2fabb9ad6 100644
--- a/drivers/net/bnxt/hsi_struct_def_dpdk.h
+++ b/drivers/net/bnxt/hsi_struct_def_dpdk.h
@@ -17291,6 +17291,261 @@ struct hwrm_ring_reset_output {
uint8_t valid;
} __attribute__((packed));
+/**************************
+ * hwrm_ring_aggint_qcaps *
+ **************************/
+
+
+/* hwrm_ring_aggint_qcaps_input (size:128b/16B) */
+struct hwrm_ring_aggint_qcaps_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFE - Reserved for internal processors
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+} __attribute__((packed));
+
+/* hwrm_ring_aggint_qcaps_output (size:384b/48B) */
+struct hwrm_ring_aggint_qcaps_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint32_t cmpl_params;
+ /*
+ * When this bit is set to '1', int_lat_tmr_min can be configured
+ * on completion rings.
+ */
+ #define HWRM_RING_AGGINT_QCAPS_OUTPUT_CMPL_PARAMS_INT_LAT_TMR_MIN \
+ UINT32_C(0x1)
+ /*
+ * When this bit is set to '1', int_lat_tmr_max can be configured
+ * on completion rings.
+ */
+ #define HWRM_RING_AGGINT_QCAPS_OUTPUT_CMPL_PARAMS_INT_LAT_TMR_MAX \
+ UINT32_C(0x2)
+ /*
+ * When this bit is set to '1', timer_reset can be enabled
+ * on completion rings.
+ */
+ #define HWRM_RING_AGGINT_QCAPS_OUTPUT_CMPL_PARAMS_TIMER_RESET \
+ UINT32_C(0x4)
+ /*
+ * When this bit is set to '1', ring_idle can be enabled
+ * on completion rings.
+ */
+ #define HWRM_RING_AGGINT_QCAPS_OUTPUT_CMPL_PARAMS_RING_IDLE \
+ UINT32_C(0x8)
+ /*
+ * When this bit is set to '1', num_cmpl_dma_aggr can be configured
+ * on completion rings.
+ */
+ #define HWRM_RING_AGGINT_QCAPS_OUTPUT_CMPL_PARAMS_NUM_CMPL_DMA_AGGR \
+ UINT32_C(0x10)
+ /*
+ * When this bit is set to '1', num_cmpl_dma_aggr_during_int can be
configured
+ * on completion rings.
+ */
+ #define
HWRM_RING_AGGINT_QCAPS_OUTPUT_CMPL_PARAMS_NUM_CMPL_DMA_AGGR_DURING_INT \
+ UINT32_C(0x20)
+ /*
+ * When this bit is set to '1', cmpl_aggr_dma_tmr can be configured
+ * on completion rings.
+ */
+ #define HWRM_RING_AGGINT_QCAPS_OUTPUT_CMPL_PARAMS_CMPL_AGGR_DMA_TMR \
+ UINT32_C(0x40)
+ /*
+ * When this bit is set to '1', cmpl_aggr_dma_tmr_during_int can be
configured
+ * on completion rings.
+ */
+ #define
HWRM_RING_AGGINT_QCAPS_OUTPUT_CMPL_PARAMS_CMPL_AGGR_DMA_TMR_DURING_INT \
+ UINT32_C(0x80)
+ /*
+ * When this bit is set to '1', num_cmpl_aggr_int can be configured
+ * on completion rings.
+ */
+ #define HWRM_RING_AGGINT_QCAPS_OUTPUT_CMPL_PARAMS_NUM_CMPL_AGGR_INT \
+ UINT32_C(0x100)
+ uint32_t nq_params;
+ /*
+ * When this bit is set to '1', int_lat_tmr_min can be configured
+ * on notification queues.
+ */
+ #define HWRM_RING_AGGINT_QCAPS_OUTPUT_NQ_PARAMS_INT_LAT_TMR_MIN \
+ UINT32_C(0x1)
+ /* Minimum value for num_cmpl_dma_aggr */
+ uint16_t num_cmpl_dma_aggr_min;
+ /* Maximum value for num_cmpl_dma_aggr */
+ uint16_t num_cmpl_dma_aggr_max;
+ /* Minimum value for num_cmpl_dma_aggr_during_int */
+ uint16_t num_cmpl_dma_aggr_during_int_min;
+ /* Maximum value for num_cmpl_dma_aggr_during_int */
+ uint16_t num_cmpl_dma_aggr_during_int_max;
+ /* Minimum value for cmpl_aggr_dma_tmr */
+ uint16_t cmpl_aggr_dma_tmr_min;
+ /* Maximum value for cmpl_aggr_dma_tmr */
+ uint16_t cmpl_aggr_dma_tmr_max;
+ /* Minimum value for cmpl_aggr_dma_tmr_during_int */
+ uint16_t cmpl_aggr_dma_tmr_during_int_min;
+ /* Maximum value for cmpl_aggr_dma_tmr_during_int */
+ uint16_t cmpl_aggr_dma_tmr_during_int_max;
+ /* Minimum value for int_lat_tmr_min */
+ uint16_t int_lat_tmr_min_min;
+ /* Maximum value for int_lat_tmr_min */
+ uint16_t int_lat_tmr_min_max;
+ /* Minimum value for int_lat_tmr_max */
+ uint16_t int_lat_tmr_max_min;
+ /* Maximum value for int_lat_tmr_max */
+ uint16_t int_lat_tmr_max_max;
+ /* Minimum value for num_cmpl_aggr_int */
+ uint16_t num_cmpl_aggr_int_min;
+ /* Maximum value for num_cmpl_aggr_int */
+ uint16_t num_cmpl_aggr_int_max;
+ /* The units for timer parameters, in nanoseconds. */
+ uint16_t timer_units;
+ uint8_t unused_0[1];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal
processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __attribute__((packed));
+
+/**************************************
+ * hwrm_ring_cmpl_ring_qaggint_params *
+ **************************************/
+
+
+/* hwrm_ring_cmpl_ring_qaggint_params_input (size:192b/24B) */
+struct hwrm_ring_cmpl_ring_qaggint_params_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFE - Reserved for internal processors
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* Physical number of completion ring. */
+ uint16_t ring_id;
+ uint8_t unused_0[6];
+} __attribute__((packed));
+
+/* hwrm_ring_cmpl_ring_qaggint_params_output (size:256b/32B) */
+struct hwrm_ring_cmpl_ring_qaggint_params_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint16_t flags;
+ /*
+ * When this bit is set to '1', interrupt max
+ * timer is reset whenever a completion is received.
+ */
+ #define HWRM_RING_CMPL_RING_QAGGINT_PARAMS_OUTPUT_FLAGS_TIMER_RESET \
+ UINT32_C(0x1)
+ /*
+ * When this bit is set to '1', ring idle mode
+ * aggregation will be enabled.
+ */
+ #define HWRM_RING_CMPL_RING_QAGGINT_PARAMS_OUTPUT_FLAGS_RING_IDLE \
+ UINT32_C(0x2)
+ /*
+ * Number of completions to aggregate before DMA
+ * during the normal mode.
+ */
+ uint16_t num_cmpl_dma_aggr;
+ /*
+ * Number of completions to aggregate before DMA
+ * during the interrupt mode.
+ */
+ uint16_t num_cmpl_dma_aggr_during_int;
+ /*
+ * Timer in unit of 80-nsec used to aggregate completions before
+ * DMA during the normal mode (not in interrupt mode).
+ */
+ uint16_t cmpl_aggr_dma_tmr;
+ /*
+ * Timer in unit of 80-nsec used to aggregate completions before
+ * DMA during the interrupt mode.
+ */
+ uint16_t cmpl_aggr_dma_tmr_during_int;
+ /* Minimum time (in unit of 80-nsec) between two interrupts. */
+ uint16_t int_lat_tmr_min;
+ /*
+ * Maximum wait time (in unit of 80-nsec) spent aggregating
+ * completions before signaling the interrupt after the
+ * interrupt is enabled.
+ */
+ uint16_t int_lat_tmr_max;
+ /*
+ * Minimum number of completions aggregated before signaling
+ * an interrupt.
+ */
+ uint16_t num_cmpl_aggr_int;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal
processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __attribute__((packed));
+
/*****************************************
* hwrm_ring_cmpl_ring_cfg_aggint_params *
*****************************************/
@@ -18534,6 +18789,904 @@ struct hwrm_cfa_vlan_antispoof_qcfg_output {
uint8_t valid;
} __attribute__((packed));
+/********************************
+ * hwrm_cfa_tunnel_filter_alloc *
+ ********************************/
+
+
+/* hwrm_cfa_tunnel_filter_alloc_input (size:704b/88B) */
+struct hwrm_cfa_tunnel_filter_alloc_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFE - Reserved for internal processors
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ uint32_t flags;
+ /* Setting of this flag indicates the applicability to the loopback
path. */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_FLAGS_LOOPBACK \
+ UINT32_C(0x1)
+ uint32_t enables;
+ /*
+ * This bit must be '1' for the l2_filter_id field to be
+ * configured.
+ */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_ENABLES_L2_FILTER_ID \
+ UINT32_C(0x1)
+ /*
+ * This bit must be '1' for the l2_addr field to be
+ * configured.
+ */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_ENABLES_L2_ADDR \
+ UINT32_C(0x2)
+ /*
+ * This bit must be '1' for the l2_ivlan field to be
+ * configured.
+ */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_ENABLES_L2_IVLAN \
+ UINT32_C(0x4)
+ /*
+ * This bit must be '1' for the l3_addr field to be
+ * configured.
+ */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_ENABLES_L3_ADDR \
+ UINT32_C(0x8)
+ /*
+ * This bit must be '1' for the l3_addr_type field to be
+ * configured.
+ */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_ENABLES_L3_ADDR_TYPE \
+ UINT32_C(0x10)
+ /*
+ * This bit must be '1' for the t_l3_addr_type field to be
+ * configured.
+ */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_ENABLES_T_L3_ADDR_TYPE \
+ UINT32_C(0x20)
+ /*
+ * This bit must be '1' for the t_l3_addr field to be
+ * configured.
+ */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_ENABLES_T_L3_ADDR \
+ UINT32_C(0x40)
+ /*
+ * This bit must be '1' for the tunnel_type field to be
+ * configured.
+ */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_ENABLES_TUNNEL_TYPE \
+ UINT32_C(0x80)
+ /*
+ * This bit must be '1' for the vni field to be
+ * configured.
+ */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_ENABLES_VNI \
+ UINT32_C(0x100)
+ /*
+ * This bit must be '1' for the dst_vnic_id field to be
+ * configured.
+ */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_ENABLES_DST_VNIC_ID \
+ UINT32_C(0x200)
+ /*
+ * This bit must be '1' for the mirror_vnic_id field to be
+ * configured.
+ */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_ENABLES_MIRROR_VNIC_ID \
+ UINT32_C(0x400)
+ /*
+ * This value identifies a set of CFA data structures used for an L2
+ * context.
+ */
+ uint64_t l2_filter_id;
+ /*
+ * This value sets the match value for the inner L2
+ * MAC address.
+ * Destination MAC address for RX path.
+ * Source MAC address for TX path.
+ */
+ uint8_t l2_addr[6];
+ /*
+ * This value sets VLAN ID value for inner VLAN.
+ * Only 12-bits of VLAN ID are used in setting the filter.
+ */
+ uint16_t l2_ivlan;
+ /*
+ * The value of inner destination IP address to be used in filtering.
+ * For IPv4, first four bytes represent the IP address.
+ */
+ uint32_t l3_addr[4];
+ /*
+ * The value of tunnel destination IP address to be used in filtering.
+ * For IPv4, first four bytes represent the IP address.
+ */
+ uint32_t t_l3_addr[4];
+ /*
+ * This value indicates the type of inner IP address.
+ * 4 - IPv4
+ * 6 - IPv6
+ * All others are invalid.
+ */
+ uint8_t l3_addr_type;
+ /*
+ * This value indicates the type of tunnel IP address.
+ * 4 - IPv4
+ * 6 - IPv6
+ * All others are invalid.
+ */
+ uint8_t t_l3_addr_type;
+ /* Tunnel Type. */
+ uint8_t tunnel_type;
+ /* Non-tunnel */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_NONTUNNEL \
+ UINT32_C(0x0)
+ /* Virtual eXtensible Local Area Network (VXLAN) */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_VXLAN \
+ UINT32_C(0x1)
+ /* Network Virtualization Generic Routing Encapsulation (NVGRE) */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_NVGRE \
+ UINT32_C(0x2)
+ /* Generic Routing Encapsulation (GRE) inside Ethernet payload */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_L2GRE \
+ UINT32_C(0x3)
+ /* IP in IP */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_IPIP \
+ UINT32_C(0x4)
+ /* Generic Network Virtualization Encapsulation (Geneve) */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_GENEVE \
+ UINT32_C(0x5)
+ /* Multi-Protocol Lable Switching (MPLS) */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_MPLS \
+ UINT32_C(0x6)
+ /* Stateless Transport Tunnel (STT) */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_STT \
+ UINT32_C(0x7)
+ /* Generic Routing Encapsulation (GRE) inside IP datagram payload */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_IPGRE \
+ UINT32_C(0x8)
+ /* IPV4 over virtual eXtensible Local Area Network (IPV4oVXLAN) */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_VXLAN_V4 \
+ UINT32_C(0x9)
+ /* Any tunneled traffic */
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_ANYTUNNEL \
+ UINT32_C(0xff)
+ #define HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_LAST \
+ HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_TYPE_ANYTUNNEL
+ /*
+ * tunnel_flags allows the user to indicate the tunnel tag detection
+ * for the tunnel type specified in tunnel_type.
+ */
+ uint8_t tunnel_flags;
+ /*
+ * If the tunnel_type is geneve, then this bit indicates if we
+ * need to match the geneve OAM packet.
+ * If the tunnel_type is nvgre or gre, then this bit indicates if
+ * we need to detect checksum present bit in geneve header.
+ * If the tunnel_type is mpls, then this bit indicates if we need
+ * to match mpls packet with explicit IPV4/IPV6 null header.
+ */
+ #define
HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_FLAGS_TUN_FLAGS_OAM_CHECKSUM_EXPLHDR \
+ UINT32_C(0x1)
+ /*
+ * If the tunnel_type is geneve, then this bit indicates if we
+ * need to detect the critical option bit set in the oam packet.
+ * If the tunnel_type is nvgre or gre, then this bit indicates
+ * if we need to match nvgre packets with key present bit set in
+ * gre header.
+ * If the tunnel_type is mpls, then this bit indicates if we
+ * need to match mpls packet with S bit from inner/second label.
+ */
+ #define
HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_FLAGS_TUN_FLAGS_CRITICAL_OPT_S1 \
+ UINT32_C(0x2)
+ /*
+ * If the tunnel_type is geneve, then this bit indicates if we
+ * need to match geneve packet with extended header bit set in
+ * geneve header.
+ * If the tunnel_type is nvgre or gre, then this bit indicates
+ * if we need to match nvgre packets with sequence number
+ * present bit set in gre header.
+ * If the tunnel_type is mpls, then this bit indicates if we
+ * need to match mpls packet with S bit from out/first label.
+ */
+ #define
HWRM_CFA_TUNNEL_FILTER_ALLOC_INPUT_TUNNEL_FLAGS_TUN_FLAGS_EXTHDR_SEQNUM_S0 \
+ UINT32_C(0x4)
+ /*
+ * Virtual Network Identifier (VNI). Only valid with
+ * tunnel_types VXLAN, NVGRE, and Geneve.
+ * Only lower 24-bits of VNI field are used
+ * in setting up the filter.
+ */
+ uint32_t vni;
+ /* Logical VNIC ID of the destination VNIC. */
+ uint32_t dst_vnic_id;
+ /*
+ * Logical VNIC ID of the VNIC where traffic is
+ * mirrored.
+ */
+ uint32_t mirror_vnic_id;
+} __attribute__((packed));
+
+/* hwrm_cfa_tunnel_filter_alloc_output (size:192b/24B) */
+struct hwrm_cfa_tunnel_filter_alloc_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /* This value is an opaque id into CFA data structures. */
+ uint64_t tunnel_filter_id;
+ /*
+ * This is the ID of the flow associated with this
+ * filter.
+ * This value shall be used to match and associate the
+ * flow identifier returned in completion records.
+ * A value of 0xFFFFFFFF shall indicate no flow id.
+ */
+ uint32_t flow_id;
+ uint8_t unused_0[3];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal
processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __attribute__((packed));
+
+/*******************************
+ * hwrm_cfa_tunnel_filter_free *
+ *******************************/
+
+
+/* hwrm_cfa_tunnel_filter_free_input (size:192b/24B) */
+struct hwrm_cfa_tunnel_filter_free_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFE - Reserved for internal processors
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* This value is an opaque id into CFA data structures. */
+ uint64_t tunnel_filter_id;
+} __attribute__((packed));
+
+/* hwrm_cfa_tunnel_filter_free_output (size:128b/16B) */
+struct hwrm_cfa_tunnel_filter_free_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal
processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __attribute__((packed));
+
+/***************************************
+ * hwrm_cfa_redirect_tunnel_type_alloc *
+ ***************************************/
+
+
+/* hwrm_cfa_redirect_tunnel_type_alloc_input (size:192b/24B) */
+struct hwrm_cfa_redirect_tunnel_type_alloc_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFE - Reserved for internal processors
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* The destination function id, to whom the traffic is redirected. */
+ uint16_t dest_fid;
+ /* Tunnel Type. */
+ uint8_t tunnel_type;
+ /* Non-tunnel */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_NONTUNNEL
\
+ UINT32_C(0x0)
+ /* Virtual eXtensible Local Area Network (VXLAN) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_VXLAN \
+ UINT32_C(0x1)
+ /* Network Virtualization Generic Routing Encapsulation (NVGRE) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_NVGRE \
+ UINT32_C(0x2)
+ /* Generic Routing Encapsulation (GRE) inside Ethernet payload */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_L2GRE \
+ UINT32_C(0x3)
+ /* IP in IP */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_IPIP \
+ UINT32_C(0x4)
+ /* Generic Network Virtualization Encapsulation (Geneve) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_GENEVE \
+ UINT32_C(0x5)
+ /* Multi-Protocol Lable Switching (MPLS) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_MPLS \
+ UINT32_C(0x6)
+ /* Stateless Transport Tunnel (STT) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_STT \
+ UINT32_C(0x7)
+ /* Generic Routing Encapsulation (GRE) inside IP datagram payload */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_IPGRE \
+ UINT32_C(0x8)
+ /* IPV4 over virtual eXtensible Local Area Network (IPV4oVXLAN) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_VXLAN_V4 \
+ UINT32_C(0x9)
+ /* Enhance Generic Routing Encapsulation (GRE version 1) inside IP
datagram payload */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_IPGRE_V1 \
+ UINT32_C(0xa)
+ /* Any tunneled traffic */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_ANYTUNNEL
\
+ UINT32_C(0xff)
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_LAST \
+ HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_TUNNEL_TYPE_ANYTUNNEL
+ /* Tunnel alloc flags. */
+ uint8_t flags;
+ /* Setting of this flag indicates modify existing redirect tunnel to
new destination function ID. */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_ALLOC_INPUT_FLAGS_MODIFY_DST \
+ UINT32_C(0x1)
+ uint8_t unused_0[4];
+} __attribute__((packed));
+
+/* hwrm_cfa_redirect_tunnel_type_alloc_output (size:128b/16B) */
+struct hwrm_cfa_redirect_tunnel_type_alloc_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal
processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __attribute__((packed));
+
+/**************************************
+ * hwrm_cfa_redirect_tunnel_type_free *
+ **************************************/
+
+
+/* hwrm_cfa_redirect_tunnel_type_free_input (size:192b/24B) */
+struct hwrm_cfa_redirect_tunnel_type_free_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFE - Reserved for internal processors
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* The destination function id, to whom the traffic is redirected. */
+ uint16_t dest_fid;
+ /* Tunnel Type. */
+ uint8_t tunnel_type;
+ /* Non-tunnel */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_NONTUNNEL \
+ UINT32_C(0x0)
+ /* Virtual eXtensible Local Area Network (VXLAN) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_VXLAN \
+ UINT32_C(0x1)
+ /* Network Virtualization Generic Routing Encapsulation (NVGRE) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_NVGRE \
+ UINT32_C(0x2)
+ /* Generic Routing Encapsulation (GRE) inside Ethernet payload */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_L2GRE \
+ UINT32_C(0x3)
+ /* IP in IP */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_IPIP \
+ UINT32_C(0x4)
+ /* Generic Network Virtualization Encapsulation (Geneve) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_GENEVE \
+ UINT32_C(0x5)
+ /* Multi-Protocol Lable Switching (MPLS) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_MPLS \
+ UINT32_C(0x6)
+ /* Stateless Transport Tunnel (STT) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_STT \
+ UINT32_C(0x7)
+ /* Generic Routing Encapsulation (GRE) inside IP datagram payload */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_IPGRE \
+ UINT32_C(0x8)
+ /* IPV4 over virtual eXtensible Local Area Network (IPV4oVXLAN) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_VXLAN_V4 \
+ UINT32_C(0x9)
+ /* Enhance Generic Routing Encapsulation (GRE version 1) inside IP
datagram payload */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_IPGRE_V1 \
+ UINT32_C(0xa)
+ /* Any tunneled traffic */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_ANYTUNNEL \
+ UINT32_C(0xff)
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_LAST \
+ HWRM_CFA_REDIRECT_TUNNEL_TYPE_FREE_INPUT_TUNNEL_TYPE_ANYTUNNEL
+ uint8_t unused_0[5];
+} __attribute__((packed));
+
+/* hwrm_cfa_redirect_tunnel_type_free_output (size:128b/16B) */
+struct hwrm_cfa_redirect_tunnel_type_free_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal
processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __attribute__((packed));
+
+/**************************************
+ * hwrm_cfa_redirect_tunnel_type_info *
+ **************************************/
+
+
+/* hwrm_cfa_redirect_tunnel_type_info_input (size:192b/24B) */
+struct hwrm_cfa_redirect_tunnel_type_info_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFE - Reserved for internal processors
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* The source function id. */
+ uint16_t src_fid;
+ /* Tunnel Type. */
+ uint8_t tunnel_type;
+ /* Non-tunnel */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_INFO_INPUT_TUNNEL_TYPE_NONTUNNEL \
+ UINT32_C(0x0)
+ /* Virtual eXtensible Local Area Network (VXLAN) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_INFO_INPUT_TUNNEL_TYPE_VXLAN \
+ UINT32_C(0x1)
+ /* Network Virtualization Generic Routing Encapsulation (NVGRE) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_INFO_INPUT_TUNNEL_TYPE_NVGRE \
+ UINT32_C(0x2)
+ /* Generic Routing Encapsulation (GRE) inside Ethernet payload */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_INFO_INPUT_TUNNEL_TYPE_L2GRE \
+ UINT32_C(0x3)
+ /* IP in IP */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_INFO_INPUT_TUNNEL_TYPE_IPIP \
+ UINT32_C(0x4)
+ /* Generic Network Virtualization Encapsulation (Geneve) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_INFO_INPUT_TUNNEL_TYPE_GENEVE \
+ UINT32_C(0x5)
+ /* Multi-Protocol Lable Switching (MPLS) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_INFO_INPUT_TUNNEL_TYPE_MPLS \
+ UINT32_C(0x6)
+ /* Stateless Transport Tunnel (STT) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_INFO_INPUT_TUNNEL_TYPE_STT \
+ UINT32_C(0x7)
+ /* Generic Routing Encapsulation (GRE) inside IP datagram payload */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_INFO_INPUT_TUNNEL_TYPE_IPGRE \
+ UINT32_C(0x8)
+ /* IPV4 over virtual eXtensible Local Area Network (IPV4oVXLAN) */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_INFO_INPUT_TUNNEL_TYPE_VXLAN_V4 \
+ UINT32_C(0x9)
+ /* Enhance Generic Routing Encapsulation (GRE version 1) inside IP
datagram payload */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_INFO_INPUT_TUNNEL_TYPE_IPGRE_V1 \
+ UINT32_C(0xa)
+ /* Any tunneled traffic */
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_INFO_INPUT_TUNNEL_TYPE_ANYTUNNEL \
+ UINT32_C(0xff)
+ #define HWRM_CFA_REDIRECT_TUNNEL_TYPE_INFO_INPUT_TUNNEL_TYPE_LAST \
+ HWRM_CFA_REDIRECT_TUNNEL_TYPE_INFO_INPUT_TUNNEL_TYPE_ANYTUNNEL
+ uint8_t unused_0[5];
+} __attribute__((packed));
+
+/* hwrm_cfa_redirect_tunnel_type_info_output (size:128b/16B) */
+struct hwrm_cfa_redirect_tunnel_type_info_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /* The destination function id, to whom the traffic is redirected. */
+ uint16_t dest_fid;
+ uint8_t unused_0[5];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal
processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __attribute__((packed));
+
+/* hwrm_vxlan_ipv4_hdr (size:128b/16B) */
+struct hwrm_vxlan_ipv4_hdr {
+ /* IPv4 version and header length. */
+ uint8_t ver_hlen;
+ /* IPv4 header length */
+ #define HWRM_VXLAN_IPV4_HDR_VER_HLEN_HEADER_LENGTH_MASK UINT32_C(0xf)
+ #define HWRM_VXLAN_IPV4_HDR_VER_HLEN_HEADER_LENGTH_SFT 0
+ /* Version */
+ #define HWRM_VXLAN_IPV4_HDR_VER_HLEN_VERSION_MASK UINT32_C(0xf0)
+ #define HWRM_VXLAN_IPV4_HDR_VER_HLEN_VERSION_SFT 4
+ /* IPv4 type of service. */
+ uint8_t tos;
+ /* IPv4 identification. */
+ uint16_t ip_id;
+ /* IPv4 flags and offset. */
+ uint16_t flags_frag_offset;
+ /* IPv4 TTL. */
+ uint8_t ttl;
+ /* IPv4 protocol. */
+ uint8_t protocol;
+ /* IPv4 source address. */
+ uint32_t src_ip_addr;
+ /* IPv4 destination address. */
+ uint32_t dest_ip_addr;
+} __attribute__((packed));
+
+/* hwrm_vxlan_ipv6_hdr (size:320b/40B) */
+struct hwrm_vxlan_ipv6_hdr {
+ /* IPv6 version, traffic class and flow label. */
+ uint32_t ver_tc_flow_label;
+ /* IPv6 version shift */
+ #define HWRM_VXLAN_IPV6_HDR_VER_TC_FLOW_LABEL_VER_SFT \
+ UINT32_C(0x1c)
+ /* IPv6 version mask */
+ #define HWRM_VXLAN_IPV6_HDR_VER_TC_FLOW_LABEL_VER_MASK \
+ UINT32_C(0xf0000000)
+ /* IPv6 TC shift */
+ #define HWRM_VXLAN_IPV6_HDR_VER_TC_FLOW_LABEL_TC_SFT \
+ UINT32_C(0x14)
+ /* IPv6 TC mask */
+ #define HWRM_VXLAN_IPV6_HDR_VER_TC_FLOW_LABEL_TC_MASK \
+ UINT32_C(0xff00000)
+ /* IPv6 flow label shift */
+ #define HWRM_VXLAN_IPV6_HDR_VER_TC_FLOW_LABEL_FLOW_LABEL_SFT \
+ UINT32_C(0x0)
+ /* IPv6 flow label mask */
+ #define HWRM_VXLAN_IPV6_HDR_VER_TC_FLOW_LABEL_FLOW_LABEL_MASK \
+ UINT32_C(0xfffff)
+ #define HWRM_VXLAN_IPV6_HDR_VER_TC_FLOW_LABEL_LAST \
+ HWRM_VXLAN_IPV6_HDR_VER_TC_FLOW_LABEL_FLOW_LABEL_MASK
+ /* IPv6 payload length. */
+ uint16_t payload_len;
+ /* IPv6 next header. */
+ uint8_t next_hdr;
+ /* IPv6 TTL. */
+ uint8_t ttl;
+ /* IPv6 source address. */
+ uint32_t src_ip_addr[4];
+ /* IPv6 destination address. */
+ uint32_t dest_ip_addr[4];
+} __attribute__((packed));
+
+/* hwrm_cfa_encap_data_vxlan (size:640b/80B) */
+struct hwrm_cfa_encap_data_vxlan {
+ /* Source MAC address. */
+ uint8_t src_mac_addr[6];
+ /* reserved. */
+ uint16_t unused_0;
+ /* Destination MAC address. */
+ uint8_t dst_mac_addr[6];
+ /* Number of VLAN tags. */
+ uint8_t num_vlan_tags;
+ /* reserved. */
+ uint8_t unused_1;
+ /* Outer VLAN TPID. */
+ uint16_t ovlan_tpid;
+ /* Outer VLAN TCI. */
+ uint16_t ovlan_tci;
+ /* Inner VLAN TPID. */
+ uint16_t ivlan_tpid;
+ /* Inner VLAN TCI. */
+ uint16_t ivlan_tci;
+ /* L3 header fields. */
+ uint32_t l3[10];
+ /* IP version mask. */
+ #define HWRM_CFA_ENCAP_DATA_VXLAN_L3_VER_MASK UINT32_C(0xf)
+ /* IP version 4. */
+ #define HWRM_CFA_ENCAP_DATA_VXLAN_L3_VER_IPV4 UINT32_C(0x4)
+ /* IP version 6. */
+ #define HWRM_CFA_ENCAP_DATA_VXLAN_L3_VER_IPV6 UINT32_C(0x6)
+ #define HWRM_CFA_ENCAP_DATA_VXLAN_L3_LAST \
+ HWRM_CFA_ENCAP_DATA_VXLAN_L3_VER_IPV6
+ /* UDP source port. */
+ uint16_t src_port;
+ /* UDP destination port. */
+ uint16_t dst_port;
+ /* VXLAN Network Identifier. */
+ uint32_t vni;
+ /* 3 bytes VXLAN header reserve fields from 1st dword of the VXLAN
header. */
+ uint8_t hdr_rsvd0[3];
+ /* 1 byte VXLAN header reserve field from 2nd dword of the VXLAN
header. */
+ uint8_t hdr_rsvd1;
+ /* VXLAN header flags field. */
+ uint8_t hdr_flags;
+ uint8_t unused[3];
+} __attribute__((packed));
+
+/*******************************
+ * hwrm_cfa_encap_record_alloc *
+ *******************************/
+
+
+/* hwrm_cfa_encap_record_alloc_input (size:832b/104B) */
+struct hwrm_cfa_encap_record_alloc_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFE - Reserved for internal processors
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ uint32_t flags;
+ /* Setting of this flag indicates the applicability to the loopback
path. */
+ #define HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_FLAGS_LOOPBACK \
+ UINT32_C(0x1)
+ /* Encapsulation Type. */
+ uint8_t encap_type;
+ /* Virtual eXtensible Local Area Network (VXLAN) */
+ #define HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_ENCAP_TYPE_VXLAN \
+ UINT32_C(0x1)
+ /* Network Virtualization Generic Routing Encapsulation (NVGRE) */
+ #define HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_ENCAP_TYPE_NVGRE \
+ UINT32_C(0x2)
+ /* Generic Routing Encapsulation (GRE) after inside Ethernet payload */
+ #define HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_ENCAP_TYPE_L2GRE \
+ UINT32_C(0x3)
+ /* IP in IP */
+ #define HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_ENCAP_TYPE_IPIP \
+ UINT32_C(0x4)
+ /* Generic Network Virtualization Encapsulation (Geneve) */
+ #define HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_ENCAP_TYPE_GENEVE \
+ UINT32_C(0x5)
+ /* Multi-Protocol Lable Switching (MPLS) */
+ #define HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_ENCAP_TYPE_MPLS \
+ UINT32_C(0x6)
+ /* VLAN */
+ #define HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_ENCAP_TYPE_VLAN \
+ UINT32_C(0x7)
+ /* Generic Routing Encapsulation (GRE) inside IP datagram payload */
+ #define HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_ENCAP_TYPE_IPGRE \
+ UINT32_C(0x8)
+ /* IPV4 over virtual eXtensible Local Area Network (IPV4oVXLAN) */
+ #define HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_ENCAP_TYPE_VXLAN_V4 \
+ UINT32_C(0x9)
+ #define HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_ENCAP_TYPE_LAST \
+ HWRM_CFA_ENCAP_RECORD_ALLOC_INPUT_ENCAP_TYPE_VXLAN_V4
+ uint8_t unused_0[3];
+ /* This value is encap data used for the given encap type. */
+ uint32_t encap_data[20];
+} __attribute__((packed));
+
+/* hwrm_cfa_encap_record_alloc_output (size:128b/16B) */
+struct hwrm_cfa_encap_record_alloc_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ /* This value is an opaque id into CFA data structures. */
+ uint32_t encap_record_id;
+ uint8_t unused_0[3];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal
processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __attribute__((packed));
+
+/******************************
+ * hwrm_cfa_encap_record_free *
+ ******************************/
+
+
+/* hwrm_cfa_encap_record_free_input (size:192b/24B) */
+struct hwrm_cfa_encap_record_free_input {
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /*
+ * The completion ring to send the completion event on. This should
+ * be the NQ ID returned from the `nq_alloc` HWRM command.
+ */
+ uint16_t cmpl_ring;
+ /*
+ * The sequence ID is used by the driver for tracking multiple
+ * commands. This ID is treated as opaque data by the firmware and
+ * the value is returned in the `hwrm_resp_hdr` upon completion.
+ */
+ uint16_t seq_id;
+ /*
+ * The target ID of the command:
+ * * 0x0-0xFFF8 - The function ID
+ * * 0xFFF8-0xFFFE - Reserved for internal processors
+ * * 0xFFFF - HWRM
+ */
+ uint16_t target_id;
+ /*
+ * A physical address pointer pointing to a host buffer that the
+ * command's response data will be written. This can be either a host
+ * physical address (HPA) or a guest physical address (GPA) and must
+ * point to a physically contiguous block of memory.
+ */
+ uint64_t resp_addr;
+ /* This value is an opaque id into CFA data structures. */
+ uint32_t encap_record_id;
+ uint8_t unused_0[4];
+} __attribute__((packed));
+
+/* hwrm_cfa_encap_record_free_output (size:128b/16B) */
+struct hwrm_cfa_encap_record_free_output {
+ /* The specific error status for the command. */
+ uint16_t error_code;
+ /* The HWRM command request type. */
+ uint16_t req_type;
+ /* The sequence ID from the original command. */
+ uint16_t seq_id;
+ /* The length of the response data in number of bytes. */
+ uint16_t resp_len;
+ uint8_t unused_0[7];
+ /*
+ * This field is used in Output records to indicate that the output
+ * is completely written to RAM. This field should be read as '1'
+ * to indicate that the output has been completely written.
+ * When writing a command completion or response to an internal
processor,
+ * the order of writes has to be such that this field is written last.
+ */
+ uint8_t valid;
+} __attribute__((packed));
+
/********************************
* hwrm_cfa_ntuple_filter_alloc *
********************************/
--
2.17.1 (Apple Git-112)
