On Mon, Sep 29, 2014 at 2:53 AM, Hiroshi Shimamoto <h-shimamoto at
ct.jp.nec.com>
wrote:
> Hi,
>
>> Subject: Re: [dpdk-dev] DPDK doesn't work with iommu=pt
>>
>> iommu=pt effectively disables iommu for the kernel and iommu is
>> enabled only for KVM.
>> http://lwn.net/Articles/329174/
>
> thanks for pointing that.
>
> Okay, I think DPDK cannot handle IOMMU because of no kernel code in
> DPDK application.
>
> And now, I think "iommu=pt" doesn't work correctly DMA on host PMD
> causes DMAR fault which means IOMMU catches a wrong operation.
> Will dig around "iommu=pt".
>
I agree with your analysis, It seems that a fairly recent patch (3~4)
months has introduced a bug that confuses unprotected DMA access with an
iommu access, by the device and produces an equivalent of a page fault.
>>
>> Basically unless you have KVM running you can remove both lines for
>> the same effect.
>> On the other hand if you do have KVM and you do want iommu=on You can
>> remove the iommu=pt for the same performance because AFAIK unlike the
>> kernel drivers DPDK doesn't dma_map and dma_unman each and every
>> ingress/egress packet (Please correct me if I'm wrong), and will not
>> suffer any performance penalties.
>
> I also tried "iommu=on", but it didn't fix the issue.
> I saw the same error messages in kernel.
>
Just to clarify, what I suggested you to try is leaving only this string in
the command line "intel_iommu=on". w/o iommu=pt.
But this would work iff DPDK can handle iota's (I/O virtual addresses).
> [ 46.978097] dmar: DRHD: handling fault status reg 2
> [ 46.978120] dmar: DMAR:[DMA Read] Request device [21:00.0] fault addr
aa010000
> DMAR:[fault reason 02] Present bit in context entry is clear
>
> thanks,
> Hiroshi
>
>>
>> FYI. Kernel NIC drivers:
>> When iommu=on{,strict} the kernel network drivers will suffer a heavy
>> performance penalty due to regular IOVA modifications (both HW and SW
>> at fault here). Ixgbe and Mellanox reuse dma_mapped pages on the
>> receive side to avoid this penalty, but still suffer from iommu on TX.
>>
>> On Fri, Sep 26, 2014 at 5:47 PM, Choi, Sy Jong <sy.jong.choi at intel.com>
wrote:
>> > Hi Shimamoto-san,
>> >
>> > There are a lot of sighting relate to "DMAR:[fault reason 06] PTE Read
access is not set"
>> > https://www.mail-archive.com/kvm at vger.kernel.org/msg106573.html
>> >
>> > This might be related to IOMMU, and kernel code.
>> >
>> > Here is what we know :-
>> > 1) Disabling VT-d in bios also removed the symptom
>> > 2) Switch to another OS distribution also removed the symptom
>> > 3) even different HW we will not see the symptom. In my case, switch
from Engineering board to EPSD board.
>> >
>> > Regards,
>> > Choi, Sy Jong
>> > Platform Application Engineer
>> >
>> >
>> > -----Original Message-----
>> > From: dev [mailto:dev-bounces at dpdk.org] On Behalf Of Hiroshi Shimamoto
>> > Sent: Friday, September 26, 2014 5:14 PM
>> > To: dev at dpdk.org
>> > Cc: Hayato Momma
>> > Subject: [dpdk-dev] DPDK doesn't work with iommu=pt
>> >
>> > I encountered an issue that DPDK doesn't work with "iommu=pt intel_
iommu=on"
>> > on HP ProLiant DL380p Gen8 server. I'm using the following environment;
>> >
>> > HW: ProLiant DL380p Gen8
>> > CPU: E5-2697 v2
>> > OS: RHEL7
>> > kernel: kernel-3.10.0-123 and the latest kernel 3.17-rc6+
>> > DPDK: v1.7.1-53-gce5abac
>> > NIC: 82599ES
>> >
>> > When boot with "iommu=pt intel_iommu=on", I got the below message and
no packets are handled.
>> >
>> > [ 120.809611] dmar: DRHD: handling fault status reg 2
>> > [ 120.809635] dmar: DMAR:[DMA Read] Request device [21:00.0] fault
addr aa010000
>> > DMAR:[fault reason 02] Present bit in context entry is clear
>> >
>> > How to reproduce;
>> > just run testpmd
>> > # ./testpmd -c 0xf -n 4 -- -i
>> >
>> > Configuring Port 0 (socket 0)
>> > PMD: ixgbe_dev_tx_queue_setup(): sw_ring=0x7ffff54eafc0
>> > hw_ring=0x7ffff4200000
dma_addr=0xaa000000
>> > PMD: ixgbe_dev_tx_queue_setup(): Using full-featured tx code path
>> > PMD: ixgbe_dev_tx_queue_setup(): - txq_flags = 0 [IXGBE
_SIMPLE_FLAGS=f01]
>> > PMD: ixgbe_dev_tx_queue_setup(): - tx_rs_thresh = 32 [RTE_PMD_IXGBE
_TX_MAX_BURST=32]
>> > PMD: ixgbe_dev_rx_queue_setup(): sw_ring=0x7ffff54ea740
>> > hw_ring=0x7ffff4210000
dma_addr=0xaa010000
>> > PMD: check_rx_burst_bulk_alloc_preconditions(): Rx Burst Bulk Alloc
Preconditions: rxq->rx_free_thresh=0,
>> RTE_PMD_IXGBE_RX_MAX_BURST=32
>> > PMD: ixgbe_dev_rx_queue_setup(): Rx Burst Bulk Alloc Preconditions are
not satisfied, Scattered Rx is requested, or
>> RTE_LIBRTE_IXGBE_RX_ALLOW_BULK_ALLOC is not enabled (port=0, queue=0).
>> > PMD: check_rx_burst_bulk_alloc_preconditions(): Rx Burst Bulk Alloc
Preconditions: rxq->rx_free_thresh=0,
>> RTE_PMD_IXGBE_RX_MAX_BURST=32
>> >
>> > testpmd> start
>> > io packet forwarding - CRC stripping disabled - packets/burst=32
>> > nb forwarding cores=1 - nb forwarding ports=2
>> > RX queues=1 - RX desc=128 - RX free threshold=0
>> > RX threshold registers: pthresh=8 hthresh=8 wthresh=0
>> > TX queues=1 - TX desc=512 - TX free threshold=0
>> > TX threshold registers: pthresh=32 hthresh=0 wthresh=0
>> > TX RS bit threshold=0 - TXQ flags=0x0
>> >
>> >
>> > and ping from another box to this server.
>> > # ping6 -I eth2 ff02::1
>> >
>> > I got the below error message and no packet is received.
>> > I couldn't see any increase RX/TX count in testpmt statistics
>> >
>> > testpmd> show port stats 0
>> >
>> > ######################## NIC statistics for port 0
########################
>> > RX-packets: 6 RX-missed: 0 RX-bytes: 732
>> > RX-badcrc: 0 RX-badlen: 0 RX-errors: 0
>> > RX-nombuf: 0
>> > TX-packets: 0 TX-errors: 0 TX-bytes: 0
>> >
############################################################################
>> > testpmd> show port stats 0
>> >
>> > ######################## NIC statistics for port 0
########################
>> > RX-packets: 6 RX-missed: 0 RX-bytes: 732
>> > RX-badcrc: 0 RX-badlen: 0 RX-errors: 0
>> > RX-nombuf: 0
>> > TX-packets: 0 TX-errors: 0 TX-bytes: 0
>> >
############################################################################
>> >
>> >
>> > The fault addr in error message must be RX DMA descriptor
>> >
>> > error message
>> > [ 120.809635] dmar: DMAR:[DMA Read] Request device [21:00.0] fault
addr aa010000
>> >
>> > log in testpmd
>> > PMD: ixgbe_dev_rx_queue_setup(): sw_ring=0x7ffff54ea740
>> > hw_ring=0x7ffff4210000
dma_addr=0xaa010000
>> >
>> > I think the NIC received a packet in fifo and try to put into memory
with DMA.
>> > Before starting DMA, the NIC get the target address from RX
descriptors in RDBA register.
>> > But accessing RX descriptors failed in IOMMU unit and reported it to
the kernel.
>> >
>> > DMAR:[fault reason 02] Present bit in context entry is clear
>> >
>> > The error message looks there is no valid entry in IOMMU.
>> >
>> > I think the following issue is very similar, but using Ubuntu14.04
couldn't fix in my case.
>> > http://thread.gmane.org/gmane.comp.networking.dpdk.devel/2281
>> >
>> > I tried Ubuntu14.04.1 and got the below error.
>> >
>> > [ 199.710191] dmar: DRHD: handling fault status reg 2
>> > [ 199.710896] dmar: DMAR:[DMA Read] Request device [21:00.0] fault
addr 7c24df000
>> > [ 199.710896] DMAR:[fault reason 06] PTE Read access is not set
>> >
>> > Currently I could see this issue on HP ProLiant DL380p Gen8 only.
>> > Is there any idea?
>> > Has anyone noticed this issue?
>> >
>> > Note: we're thinking to use SR-IOV and DPDK app in the same box.
>> > The box has 2 NICs, one for SR-IOV and pass through to VM, one (no SR-
IOV) for DPDK app in host.
>> >
>> > thanks,
>> > Hiroshi
