The device information cannot be gotten correctly before
the configuration is set. Because on some NICs the
information has dependence on the configuration.
Fixes: 3be82f5cc5e3 ("ethdev: support PMD-tuned Tx/Rx parameters")
Signed-off-by: Wenzhuo Lu <wenzhuo...@intel.com>
---
lib/librte_ethdev/rte_ethdev.c | 47 +++++++++++++++++++++---------------------
1 file changed, 24 insertions(+), 23 deletions(-)
diff --git a/lib/librte_ethdev/rte_ethdev.c b/lib/librte_ethdev/rte_ethdev.c
index 3d556a8..9d60bea 100644
--- a/lib/librte_ethdev/rte_ethdev.c
+++ b/lib/librte_ethdev/rte_ethdev.c
@@ -1017,28 +1017,6 @@ struct rte_eth_dev *
RTE_ETH_VALID_PORTID_OR_ERR_RET(port_id, -EINVAL);
- dev = &rte_eth_devices[port_id];
-
- RTE_FUNC_PTR_OR_ERR_RET(*dev->dev_ops->dev_infos_get, -ENOTSUP);
- RTE_FUNC_PTR_OR_ERR_RET(*dev->dev_ops->dev_configure, -ENOTSUP);
-
- rte_eth_dev_info_get(port_id, &dev_info);
-
- /* If number of queues specified by application for both Rx and Tx is
- * zero, use driver preferred values. This cannot be done individually
- * as it is valid for either Tx or Rx (but not both) to be zero.
- * If driver does not provide any preferred valued, fall back on
- * EAL defaults.
- */
- if (nb_rx_q == 0 && nb_tx_q == 0) {
- nb_rx_q = dev_info.default_rxportconf.nb_queues;
- if (nb_rx_q == 0)
- nb_rx_q = RTE_ETH_DEV_FALLBACK_RX_NBQUEUES;
- nb_tx_q = dev_info.default_txportconf.nb_queues;
- if (nb_tx_q == 0)
- nb_tx_q = RTE_ETH_DEV_FALLBACK_TX_NBQUEUES;
- }
-
if (nb_rx_q > RTE_MAX_QUEUES_PER_PORT) {
RTE_ETHDEV_LOG(ERR,
"Number of RX queues requested (%u) is greater than max
supported(%d)\n",
@@ -1053,6 +1031,11 @@ struct rte_eth_dev *
return -EINVAL;
}
+ dev = &rte_eth_devices[port_id];
+
+ RTE_FUNC_PTR_OR_ERR_RET(*dev->dev_ops->dev_infos_get, -ENOTSUP);
+ RTE_FUNC_PTR_OR_ERR_RET(*dev->dev_ops->dev_configure, -ENOTSUP);
+
if (dev->data->dev_started) {
RTE_ETHDEV_LOG(ERR,
"Port %u must be stopped to allow configuration\n",
@@ -1060,8 +1043,26 @@ struct rte_eth_dev *
return -EBUSY;
}
- /* Copy the dev_conf parameter into the dev structure */
+ /* Copy the dev_conf parameter into the dev structure,
+ * then get the info.
+ */
memcpy(&dev->data->dev_conf, &local_conf, sizeof(dev->data->dev_conf));
+ rte_eth_dev_info_get(port_id, &dev_info);
+
+ /* If number of queues specified by application for both Rx and Tx is
+ * zero, use driver preferred values. This cannot be done individually
+ * as it is valid for either Tx or Rx (but not both) to be zero.
+ * If driver does not provide any preferred valued, fall back on
+ * EAL defaults.
+ */
+ if (nb_rx_q == 0 && nb_tx_q == 0) {
+ nb_rx_q = dev_info.default_rxportconf.nb_queues;
+ if (nb_rx_q == 0)
+ nb_rx_q = RTE_ETH_DEV_FALLBACK_RX_NBQUEUES;
+ nb_tx_q = dev_info.default_txportconf.nb_queues;
+ if (nb_tx_q == 0)
+ nb_tx_q = RTE_ETH_DEV_FALLBACK_TX_NBQUEUES;
+ }
/*
* Check that the numbers of RX and TX queues are not greater
--
1.9.3
