PMD is combined of 'PM' - a thread model and 'D' - a user space driver. DPDK provides optimized RX and TX in Driver on fast path. DPDK provides a single thread core affinity model to demonstrate the best IO with minimum noisy penalty. They are not tight coupling as Venky said.
In some cases, you may only pick up the RX/TX but give up the thread model DPDK provided. Just take care to well handle the penalty may exist in the specific thread model. For DPDK, we do think on it, and start to deal with the negative factor. In another perspective, the more cycles we gain on 'D' side the more we could spend on 'PM' side to cancel the penalty out. Maybe a sample using RX/TX without dead polling is a good start. But cannot expect more on user space wake up latency so far. Regards, Liang Cunming > -----Original Message----- > From: dev [mailto:dev-bounces at dpdk.org] On Behalf Of Venkatesan, Venky > Sent: Wednesday, August 27, 2014 10:54 PM > To: dev at dpdk.org > Subject: Re: [dpdk-dev] overcommitting CPUs > > DPDK currently isn't exactly poll mode - it has an API that receives and > transmits packets. How you enter that API could be interrupt or polled > -we've left that up to the application to decide, rather than force a > interrupt/NAPI type architecture. I do agree with Alex in that > implementing a interrupt/load driven entry point as an option will make > it usable more widely. There are multiple challenges here - managing the > latency of an interrupt driven scheme in a user-space context, not to > mention very high jitter rates to mention a few. > > That said, overcommitment of CPUs can be achieved in other ways as well. > You could allocate and enforce CPU sharing via cgroups, and allocate x% > of a core to the DPDK pthread. It does introduce a degree of > indeterminism to when the DPDK pthread gets scheduled back in (depending > on how many other threads are running on that core). But it is another > option ... > > Regards, > -Venky > > On 8/27/2014 1:40 AM, Alex Markuze wrote: > > IMHO adding "Interrupt Mode" to dpdk is important as this can open > > DPDK to a larger public of consumers, I can easily imagine someone > > trying to find user space networking solution (And deciding against > > verbs - RDMA) for the obvious reasons and not needing deterministic > > latency. > > > > A few thoughts: > > > > Deterministic Latency: Its a fiction in a sence that this something > > you will be able to see only in a small controlled environment. As > > network latencies in Data Centres(DC) are dominated by switch queuing > > (One good reference is http://fastpass.mit.edu that Vincent shared a > > few days back). > > > > Virtual environments: In virtual environments this is especially > > interesting as the NIC driver(Hypervisor) is working in IRQ mode which > > unless the Interrupts are pinned to different cpus then the VM will > > have a disruptive effect on the VM's performance. Moving to interrupt > > mode mode in paravirtualised environments makes sense as in any > > environment that is not carefully crafted you should not expect any > > deterministic guaranties and would opt for a simpler programming model > > - like interrupt mode. > > > > NAPI: With 10G NICs Most CPUs poll rate is faster then the NIC message > > rate resulting in 1:1 napi_poll callback to IRQ ratio this is true > > even with small packets. In some cases where the CPU is working slower > > - for example when intel_iommu=on,strict is set , you can actually see > > a performance inversion where the "slower" CPU can reach higher B/W > > because the slowdown makes NAPI work with the kernel effectively > > moving to polling mode. > > > > I think that a smarter DPDK-NAPI is important, but it is a next step > > IFF the interrupt mode is adopted. > > > > On Wed, Aug 27, 2014 at 8:48 AM, Patel, Rashmin N > > <rashmin.n.patel at intel.com> wrote: > >> You're right and I've felt the same harder part of determinism with other > hypervisors' soft switch solutions as well. I think it's worth thinking about. > >> > >> Thanks, > >> Rashmin > >> > >> On Aug 26, 2014 9:15 PM, Stephen Hemminger > <stephen at networkplumber.org> wrote: > >> The way to handle switch between out of poll mode is to use IRQ coalescing > >> parameters. > >> You want to hold off IRQ until there are a couple packets or a short delay. > >> Going out of poll mode > >> is harder to determine. > >> > >> > >> On Tue, Aug 26, 2014 at 9:59 AM, Zhou, Danny <danny.zhou at intel.com> > wrote: > >> > >>>> -----Original Message----- > >>>> From: dev [mailto:dev-bounces at dpdk.org] On Behalf Of Stephen > Hemminger > >>>> Sent: Wednesday, August 27, 2014 12:39 AM > >>>> To: Michael Marchetti > >>>> Cc: dev at dpdk.org > >>>> Subject: Re: [dpdk-dev] overcommitting CPUs > >>>> > >>>> On Tue, 26 Aug 2014 16:27:14 +0000 > >>>> "Michael Marchetti" <mmarchetti at sandvine.com> wrote: > >>>> > >>>>> Hi, has there been any consideration to introduce a non-spinning > >>> network driver (interrupt based), for the purpose of overcommitting > >>>> CPUs in a virtualized environment? This would obviously have reduced > >>> high-end performance but would allow for increased guest > >>>> density (sharing of physical CPUs) on a host. > >>>>> I am interested in adding support for this kind of operation, is there > >>> any interest in the community? > >>>>> Thanks, > >>>>> > >>>>> Mike. > >>>> Better to implement a NAPI like algorithm that adapts from poll to > >>> interrupt. > >>> > >>> Agreed, but DPDK is currently pure poll-mode based, so unlike the NAPI' > >>> simple algorithm, the new heuristic algorithm should not switch from > >>> poll-mode to interrupt-mode immediately once there is no packet in the > >>> recent poll. Otherwise, mode switching will be too frequent which brings > >>> serious negative performance impact to DPDK. > >>>
