As a matter of order, I have until Saturday afternoon, right? I am seeing
reasonably good results so far but I need to find time to test in an
advanced zone with security groups and zone wide primary storage as we use
in Leaseweb. (tentative +1)
On Fri, Jan 22, 2016 at 10:35 AM, Remi Bergsma <rberg...@schubergphilis.com>
wrote:
> Hi all,
>
> My vote: +1 (binding) based on the integration tests below. These were
> tested against a 2-node KVM cluster based on CentOS7 (RPMs from the RC
> branch). The management server also runs CentOS7.
>
> In our employee cloud we run the same code against 2 XenServer 6.5
> clusters. All works fine. Especially the router vm’s are much faster
> compared to 4.6.x and 4.7.0.
>
> I will now continue testing on 4.8.0.
>
> Regards,
> Remi
>
>
> ```
> nosetests --with-marvin --marvin-config=${marvinCfg} -s -a
> tags=advanced,required_hardware=true \
> component/test_vpc_redundant.py \
> component/test_routers_iptables_default_policy.py \
> component/test_routers_network_ops.py \
> component/test_vpc_router_nics.py \
> smoke/test_loadbalance.py \
> smoke/test_internal_lb.py \
> smoke/test_ssvm.py \
> smoke/test_network.py
>
> ```
> Result:
>
> ```
> Check the password file in the Router VM ... === TestName:
> test_isolate_network_password_server | Status : SUCCESS ===
> ok
> Create a redundant VPC with two networks with two VMs in each network ...
> === TestName: test_01_create_redundant_VPC_2tiers_4VMs_4IPs_4PF_ACL |
> Status : SUCCESS ===
> ok
> Create a redundant VPC with two networks with two VMs in each network and
> check default routes ... === TestName: test_02_redundant_VPC_default_routes
> | Status : SUCCESS ===
> ok
> Create a redundant VPC with two networks with two VMs in each network ...
> === TestName:
> test_03_create_redundant_VPC_1tier_2VMs_2IPs_2PF_ACL_reboot_routers |
> Status : SUCCESS ===
> ok
> Create a redundant VPC with 1 Tier, 1 VM, 1 ACL, 1 PF and test Network GC
> Nics ... === TestName: test_04_rvpc_network_garbage_collector_nics | Status
> : SUCCESS ===
> ok
> Create a redundant VPC with 1 Tier, 1 VM, 1 ACL, 1 PF and test Network GC
> Nics ... === TestName: test_05_rvpc_multi_tiers | Status : SUCCESS ===
> ok
> Test iptables default INPUT/FORWARD policy on RouterVM ... === TestName:
> test_02_routervm_iptables_policies | Status : SUCCESS ===
> ok
> Test iptables default INPUT/FORWARD policies on VPC router ... ===
> TestName: test_01_single_VPC_iptables_policies | Status : SUCCESS ===
> ok
> Test redundant router internals ... === TestName:
> test_01_isolate_network_FW_PF_default_routes_egress_true | Status : SUCCESS
> ===
> ok
> Test redundant router internals ... === TestName:
> test_02_isolate_network_FW_PF_default_routes_egress_false | Status :
> SUCCESS ===
> ok
> Test redundant router internals ... === TestName:
> test_01_RVR_Network_FW_PF_SSH_default_routes_egress_true | Status : SUCCESS
> ===
> ok
> Test redundant router internals ... === TestName:
> test_02_RVR_Network_FW_PF_SSH_default_routes_egress_false | Status :
> SUCCESS ===
> ok
> Test redundant router internals ... === TestName:
> test_03_RVR_Network_check_router_state | Status : SUCCESS ===
> ok
> Create a VPC with two networks with one VM in each network and test nics
> after destroy ... === TestName: test_01_VPC_nics_after_destroy | Status :
> SUCCESS ===
> ok
> Create a VPC with two networks with one VM in each network and test
> default routes ... === TestName: test_02_VPC_default_routes | Status :
> SUCCESS ===
> ok
> Check that the /etc/dhcphosts.txt doesn't contain duplicate IPs ... ===
> TestName: test_router_dhcphosts | Status : SUCCESS ===
> ok
> Test to create Load balancing rule with source NAT ... === TestName:
> test_01_create_lb_rule_src_nat | Status : SUCCESS ===
> ok
> Test to create Load balancing rule with non source NAT ... === TestName:
> test_02_create_lb_rule_non_nat | Status : SUCCESS ===
> ok
> Test for assign & removing load balancing rule ... === TestName:
> test_assign_and_removal_lb | Status : SUCCESS ===
> ok
> Test create, assign, remove of an Internal LB with roundrobin http traffic
> to 3 vm's in a Single VPC ... === TestName:
> test_01_internallb_roundrobin_1VPC_3VM_HTTP_port80 | Status : SUCCESS ===
> ok
> Test create, assign, remove of an Internal LB with roundrobin http traffic
> to 3 vm's in a Redundant VPC ... === TestName:
> test_02_internallb_roundrobin_1RVPC_3VM_HTTP_port80 | Status : SUCCESS ===
> ok
> Test to verify access to loadbalancer haproxy admin stats page ... ===
> TestName: test_03_vpc_internallb_haproxy_stats_on_all_interfaces | Status :
> SUCCESS ===
> ok
> Test to verify access to loadbalancer haproxy admin stats page ... ===
> TestName: test_04_rvpc_internallb_haproxy_stats_on_all_interfaces | Status
> : SUCCESS ===
> ok
> Test SSVM Internals ... === TestName: test_03_ssvm_internals | Status :
> SUCCESS ===
> ok
> Test CPVM Internals ... === TestName: test_04_cpvm_internals | Status :
> SUCCESS ===
> ok
> Test stop SSVM ... === TestName: test_05_stop_ssvm | Status : SUCCESS ===
> ok
> Test stop CPVM ... === TestName: test_06_stop_cpvm | Status : SUCCESS ===
> ok
> Test reboot SSVM ... === TestName: test_07_reboot_ssvm | Status : SUCCESS
> ===
> ok
> Test reboot CPVM ... === TestName: test_08_reboot_cpvm | Status : SUCCESS
> ===
> ok
> Test destroy SSVM ... === TestName: test_09_destroy_ssvm | Status :
> SUCCESS ===
> ok
> Test destroy CPVM ... === TestName: test_10_destroy_cpvm | Status :
> SUCCESS ===
> ok
> test_01_vpc_privategw_acl
> (integration.smoke.test_privategw_acl.TestPrivateGwACL) ... === TestName:
> test_01_vpc_privategw_acl | Status : SUCCESS ===
> ok
> test_02_vpc_privategw_static_routes
> (integration.smoke.test_privategw_acl.TestPrivateGwACL) ... === TestName:
> test_02_vpc_privategw_static_routes | Status : SUCCESS ===
> ok
> test_03_vpc_privategw_restart_vpc_cleanup
> (integration.smoke.test_privategw_acl.TestPrivateGwACL) ... === TestName:
> test_03_vpc_privategw_restart_vpc_cleanup | Status : SUCCESS ===
> ok
> test_04_rvpc_privategw_static_routes
> (integration.smoke.test_privategw_acl.TestPrivateGwACL) ... === TestName:
> test_04_rvpc_privategw_static_routes | Status : SUCCESS ===
> ok
> Test for port forwarding on source NAT ... === TestName:
> test_01_port_fwd_on_src_nat | Status : SUCCESS ===
> ok
> Test for port forwarding on non source NAT ... === TestName:
> test_02_port_fwd_on_non_src_nat | Status : SUCCESS ===
> ok
> Test for reboot router ... === TestName: test_reboot_router | Status :
> SUCCESS ===
> ok
> Test for Router rules for network rules on acquired public IP ... ===
> TestName: test_network_rules_acquired_public_ip_1_static_nat_rule | Status
> : SUCCESS ===
> ok
> Test for Router rules for network rules on acquired public IP ... ===
> TestName: test_network_rules_acquired_public_ip_2_nat_rule | Status :
> SUCCESS ===
> ok
> Test for Router rules for network rules on acquired public IP ... ===
> TestName: test_network_rules_acquired_public_ip_3_Load_Balancer_Rule |
> Status : SUCCESS ===
> ok
>
> ----------------------------------------------------------------------
> Ran 41 tests in 22198.895s
>
> OK
> ```
>
>
> And:
>
> ```
> nosetests --with-marvin --marvin-config=${marvinCfg} -s -a
> tags=advanced,required_hardware=false \
> smoke/test_routers.py \
> smoke/test_network_acl.py \
> smoke/test_privategw_acl.py \
> smoke/test_reset_vm_on_reboot.py \
> smoke/test_vm_life_cycle.py \
> smoke/test_vpc_vpn.py \
> smoke/test_service_offerings.py \
> component/test_vpc_offerings.py \
> component/test_vpc_routers.py
> ```
>
> Result:
>
> ```
> Test router internal advanced zone ... === TestName:
> test_02_router_internal_adv | Status : SUCCESS ===
> ok
> Test restart network ... === TestName: test_03_restart_network_cleanup |
> Status : SUCCESS ===
> ok
> Test router basic setup ... === TestName: test_05_router_basic | Status :
> SUCCESS ===
> ok
> Test router advanced setup ... === TestName: test_06_router_advanced |
> Status : SUCCESS ===
> ok
> Test stop router ... === TestName: test_07_stop_router | Status : SUCCESS
> ===
> ok
> Test start router ... === TestName: test_08_start_router | Status :
> SUCCESS ===
> ok
> Test reboot router ... === TestName: test_09_reboot_router | Status :
> SUCCESS ===
> ok
> Test reset virtual machine on reboot ... === TestName:
> test_01_reset_vm_on_reboot | Status : SUCCESS ===
> ok
> Test advanced zone virtual router ... === TestName:
> test_advZoneVirtualRouter | Status : SUCCESS ===
> ok
> Test Deploy Virtual Machine ... === TestName: test_deploy_vm | Status :
> SUCCESS ===
> ok
> Test Multiple Deploy Virtual Machine ... === TestName:
> test_deploy_vm_multiple | Status : SUCCESS ===
> ok
> Test Stop Virtual Machine ... === TestName: test_01_stop_vm | Status :
> SUCCESS ===
> ok
> Test Start Virtual Machine ... === TestName: test_02_start_vm | Status :
> SUCCESS ===
> ok
> Test Reboot Virtual Machine ... === TestName: test_03_reboot_vm | Status :
> SUCCESS ===
> ok
> Test destroy Virtual Machine ... === TestName: test_06_destroy_vm | Status
> : SUCCESS ===
> ok
> Test recover Virtual Machine ... === TestName: test_07_restore_vm | Status
> : SUCCESS ===
> ok
> Test migrate VM ... === TestName: test_08_migrate_vm | Status : SUCCESS ===
> ok
> Test destroy(expunge) Virtual Machine ... === TestName: test_09_expunge_vm
> | Status : SUCCESS ===
> ok
> Test to create service offering ... === TestName:
> test_01_create_service_offering | Status : SUCCESS ===
> ok
> Test to update existing service offering ... === TestName:
> test_02_edit_service_offering | Status : SUCCESS ===
> ok
> Test to delete service offering ... === TestName:
> test_03_delete_service_offering | Status : SUCCESS ===
> ok
> Test for delete account ... === TestName: test_delete_account | Status :
> SUCCESS ===
> ok
> Test for Associate/Disassociate public IP address for admin account ...
> === TestName: test_public_ip_admin_account | Status : SUCCESS ===
> ok
> Test for Associate/Disassociate public IP address for user account ... ===
> TestName: test_public_ip_user_account | Status : SUCCESS ===
> ok
> Test for release public IP address ... === TestName: test_releaseIP |
> Status : SUCCESS ===
> ok
> Test create VPC offering ... === TestName: test_01_create_vpc_offering |
> Status : SUCCESS ===
> ok
> Test VPC offering without load balancing service ... === TestName:
> test_03_vpc_off_without_lb | Status : SUCCESS ===
> ok
> Test VPC offering without static NAT service ... === TestName:
> test_04_vpc_off_without_static_nat | Status : SUCCESS ===
> ok
> Test VPC offering without port forwarding service ... === TestName:
> test_05_vpc_off_without_pf | Status : SUCCESS ===
> ok
> Test VPC offering with invalid services ... === TestName:
> test_06_vpc_off_invalid_services | Status : SUCCESS ===
> ok
> Test update VPC offering ... === TestName: test_07_update_vpc_off | Status
> : SUCCESS ===
> ok
> Test list VPC offering ... === TestName: test_08_list_vpc_off | Status :
> SUCCESS ===
> ok
> test_09_create_redundant_vpc_offering
> (integration.component.test_vpc_offerings.TestVPCOffering) ... ===
> TestName: test_09_create_redundant_vpc_offering | Status : SUCCESS ===
> ok
> Test start/stop of router after addition of one guest network ... ===
> TestName: test_01_start_stop_router_after_addition_of_one_guest_network |
> Status : SUCCESS ===
> ok
> Test reboot of router after addition of one guest network ... ===
> TestName: test_02_reboot_router_after_addition_of_one_guest_network |
> Status : SUCCESS ===
> ok
> Test to change service offering of router after addition of one guest
> network ... === TestName:
> test_04_chg_srv_off_router_after_addition_of_one_guest_network | Status :
> SUCCESS ===
> ok
> Test destroy of router after addition of one guest network ... ===
> TestName: test_05_destroy_router_after_addition_of_one_guest_network |
> Status : SUCCESS ===
> ok
> Test to stop and start router after creation of VPC ... === TestName:
> test_01_stop_start_router_after_creating_vpc | Status : SUCCESS ===
> ok
> Test to reboot the router after creating a VPC ... === TestName:
> test_02_reboot_router_after_creating_vpc | Status : SUCCESS ===
> ok
> Tests to change service offering of the Router after ... === TestName:
> test_04_change_service_offerring_vpc | Status : SUCCESS ===
> ok
> Test to destroy the router after creating a VPC ... === TestName:
> test_05_destroy_router_after_creating_vpc | Status : SUCCESS ===
> ok
>
> ----------------------------------------------------------------------
> Ran 41 tests in 9416.577s
>
> OK
> ```
>
>
>
>
>
> On 20/01/16 23:27, "Remi Bergsma" <rberg...@schubergphilis.com> wrote:
>
> >Hi all,
> >
> >I've created a 4.7.1 release candidate, with the following artifacts up
> for a vote:
> >
> >Git Branch and Commit SH:
> >
> https://git-wip-us.apache.org/repos/asf?p=cloudstack.git;a=shortlog;h=4.7.1-RC20160120T2318
> >
> >Commit: 5ea07dc93799f28dd6c268b17514867d92dc53f7
> >
> >Source release (checksums and signatures are available at the same
> location):
> >https://dist.apache.org/repos/dist/dev/cloudstack/4.7.1/
> >
> >PGP release keys (signed using A47DDC4F):
> >https://dist.apache.org/repos/dist/release/cloudstack/KEYS
> >
> >Vote will be open for at least 72 hours.
> >
> >For sanity in tallying the vote, can PMC members please be sure to
> indicate "(binding)" with their vote?
> >
> >[ ] +1 approve
> >[ ] +0 no opinion
> >[ ] -1 disapprove (and reason why)
> >
>
--
Daan
