Had a panic moment when it appeared my i1pro meter had stopped working.
It seems I had not used it since upgrading to 18.04.LTS when I started
having problems with this issue. As I plugged the unit in gnome-control-
center opens at the device colour profile page. When I open a terminal
and try to use chartread I get:
Read Target Test Chart, Version 2.0.0
Author: Graeme W. Gill, licensed under the AGPL Version 3
usage: chartread [-options] outfile
-v Verbose mode
-c listno Set communication port from the following list (default 1)
** No ports found **
etc
or with chartread -D I get:
Read Target Test Chart, Version 2.0.0
Author: Graeme W. Gill, licensed under the AGPL Version 3
usage: chartread [-options] outfile
-v Verbose mode
-c listno Set communication port from the following list (default 1)
Argyll 'V2.0.0' Build 'Linux 64 bit' System 'Linux #81-Ubuntu SMP Tue Nov 26
12:20:02 UTC 2019 4.15.0-72-generic x86_64'
usb_check_and_add: failed to open '/dev/bus/usb/004/025'
** No ports found **
As a last resort I uninstalled gnome-control-center with synaptic and
the device (after unplug and plug in) is available again to chartread -D
:
Read Target Test Chart, Version 2.0.0
Author: Graeme W. Gill, licensed under the AGPL Version 3
usage: chartread [-options] outfile
-v Verbose mode
-c listno Set communication port from the following list (default 1)
1 = '/dev/bus/usb/004/008 (GretagMacbeth i1 Pro)'
I re-installed and it's back to no-go. It's as though gnome-control-center is
grabbing the device and not allowing access even when the window is closed.
--
You received this bug notification because you are a member of Desktop
Packages, which is subscribed to gnome-control-center in Ubuntu.
https://bugs.launchpad.net/bugs/1855615
Title:
Device colour profiles - on / off button not working Ubuntu 18.04.3LTS
Status in gnome-control-center package in Ubuntu:
New
Bug description:
I've been trying to calibrate my printer in Ubuntu 18.04.3LTS with
gnome-control-center:
Installed: 1:3.28.2-0ubuntu0.18.04.5
Candidate: 1:3.28.2-0ubuntu0.18.04.5
Version table:
*** 1:3.28.2-0ubuntu0.18.04.5 500
The least documented part of printer profiling is printing the target. Every
guide says turn off printer profile calibration, but no-one tells you how.
Through trial, error and a lot of paper and ink it seems to me as though the
on / off button next to the printer description does nothing.
If the user deletes all existing profiles the field reads Not calibrated and
no button is displayed, though on a reboot this changes to a button showing
colour management (CMS) on and two default profiles are displayed (default RGB
and default grey) with RGB selected. The output of these two states is
identical. If the setting is default RGB profile with no others loaded, then
changing Cups in a browser to Colour Correction: uncorrected refreshes the
state to Not Calibrated, though this is the only time I could force this.
Setting Cups to Colour Correction: high accuracy does result in an altered
output from the printer. I am guessing this is no colour profiling being
applied.
However if Cups Colour Correction: uncorrected is set, and a profile is
loaded in Device Colour Profiles the output from the printer is the same
whether or not the CMS on /off button is pressed. I think this is the result of
the profile applied by Device Colour Profiles in either case.
Similarly, using Cups Colour Correction: High Accuracy and a profile loaded
in Device Colour Profiles, the printer output is the same whether or not the
CMS on /off button is pressed, though the output is different from the
preceding example. I presume this is the result of two colour transformations
being carried out.
The attached images of my printer output should hopefully help explain this
situation.
To manage notifications about this bug go to:
https://bugs.launchpad.net/ubuntu/+source/gnome-control-center/+bug/1855615/+subscriptions
--
Mailing list: https://launchpad.net/~desktop-packages
Post to : [email protected]
Unsubscribe : https://launchpad.net/~desktop-packages
More help : https://help.launchpad.net/ListHelp
