On Fri, Sep 09, 2005 at 10:34:08PM +0200, Alessandro Di Rubbo wrote: > Package: kernel-image-2.6.8-2-k7 > Version: 2.6.8-16 > Followup-For: Bug #312255 > > > If I boot the system using kernel 2.6, after the message "Starting GNOME > DISPLAY MANAGER: gdm", a messy image appears, similar to my desktop > background: except for the mouse, everything is blocked. To go on I have > to reset: mysteriously, after the reboot I can use kernel 2.6 (sometimes > I have to repeat this procedure many times). > Kernel 2.4, instead, works fine. > > I installed the kernel-image-2.6.8-2-k7 package after the installation > of Debian 3.1 "sarge" with kernel-image-2.4.27-2-386. > > I use an AMD Athlon XP 1800+ CPU and an ATI Radeon 7000 graphic card on > an ASUS A7V880 motherboard (VIA KT880/VT8237 chipset).
Hi, I wonder if this might be a bug in X, though it could be just as easily a problem with the kernel. I've CCed the X maintainers, they may have some insight. > -------- > > "lspci -v" output: > > > 0000:00:00.0 Host bridge: VIA Technologies, Inc.: Unknown device 0269 > (rev 80) > Subsystem: Asustek Computer, Inc.: Unknown device 8122 > Flags: bus master, 66MHz, medium devsel, latency 64 > Memory at e0000000 (32-bit, prefetchable) [size=256M] > Capabilities: [80] AGP version 3.5 > Capabilities: [50] Power Management version 2 > > 0000:00:00.1 Host bridge: VIA Technologies, Inc.: Unknown device 1269 > Subsystem: Asustek Computer, Inc.: Unknown device 8122 > Flags: bus master, medium devsel, latency 0 > > 0000:00:00.2 Host bridge: VIA Technologies, Inc.: Unknown device 2269 > Subsystem: Asustek Computer, Inc.: Unknown device 8122 > Flags: bus master, medium devsel, latency 0 > > 0000:00:00.3 Host bridge: VIA Technologies, Inc.: Unknown device 3269 > Subsystem: Asustek Computer, Inc.: Unknown device 8122 > Flags: bus master, medium devsel, latency 0 > > 0000:00:00.4 Host bridge: VIA Technologies, Inc.: Unknown device 4269 > Subsystem: Asustek Computer, Inc.: Unknown device 8122 > Flags: bus master, medium devsel, latency 0 > > 0000:00:00.7 Host bridge: VIA Technologies, Inc.: Unknown device 7269 > Subsystem: Asustek Computer, Inc.: Unknown device 8122 > Flags: bus master, medium devsel, latency 0 > > 0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI Bridge > (prog-if 00 [Normal decode]) > Flags: bus master, 66MHz, medium devsel, latency 0 > Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 > I/O behind bridge: 0000d000-0000dfff > Memory behind bridge: fe100000-fe4fffff > Prefetchable memory behind bridge: 9ff00000-afefffff > Capabilities: [70] Power Management version 2 > > 0000:00:0f.0 RAID bus controller: VIA Technologies, Inc. VIA VT6420 SATA > RAID Controller (rev 80) > Subsystem: Asustek Computer, Inc. A7V600 motherboard > Flags: bus master, medium devsel, latency 64, IRQ 20 > I/O ports at eff0 [size=8] > I/O ports at efe4 [size=4] > I/O ports at efa8 [size=8] > I/O ports at efe0 [size=4] > I/O ports at ef90 [size=16] > I/O ports at e800 [size=256] > Capabilities: [c0] Power Management version 2 > > 0000:00:0f.1 IDE interface: VIA Technologies, Inc. > VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) > (prog-if 8a [Master SecP PriP]) > Subsystem: Asustek Computer, Inc. A7V600 motherboard > Flags: bus master, medium devsel, latency 32, IRQ 20 > I/O ports at fc00 [size=16] > Capabilities: [c0] Power Management version 2 > > 0000:00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB > 1.1 Controller (rev 81) (prog-if 00 [UHCI]) > Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 > Controller > Flags: bus master, medium devsel, latency 64, IRQ 21 > I/O ports at eec0 [size=32] > Capabilities: [80] Power Management version 2 > > 0000:00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB > 1.1 Controller (rev 81) (prog-if 00 [UHCI]) > Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 > Controller > Flags: bus master, medium devsel, latency 64, IRQ 21 > I/O ports at ef00 [size=32] > Capabilities: [80] Power Management version 2 > > 0000:00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB > 1.1 Controller (rev 81) (prog-if 00 [UHCI]) > Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 > Controller > Flags: bus master, medium devsel, latency 64, IRQ 21 > I/O ports at ef20 [size=32] > Capabilities: [80] Power Management version 2 > > 0000:00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB > 1.1 Controller (rev 81) (prog-if 00 [UHCI]) > Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 > Controller > Flags: bus master, medium devsel, latency 64, IRQ 21 > I/O ports at ef40 [size=32] > Capabilities: [80] Power Management version 2 > > 0000:00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86) > (prog-if 20 [EHCI]) > Subsystem: VIA Technologies, Inc. USB 2.0 > Flags: bus master, medium devsel, latency 64, IRQ 21 > Memory at fe900000 (32-bit, non-prefetchable) [size=256] > Capabilities: [80] Power Management version 2 > > 0000:00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge > [K8T800 South] Subsystem: Asustek Computer, Inc. A7V600 > motherboard > Flags: bus master, medium devsel, latency 0 > Capabilities: [c0] Power Management version 2 > > 0000:00:11.5 Multimedia audio controller: VIA Technologies, Inc. > VT8233/A/8235/8237 AC97 Audio Controller (rev 60) > Subsystem: Asustek Computer, Inc.: Unknown device 810d > Flags: medium devsel, IRQ 22 > I/O ports at e000 [size=256] > Capabilities: [c0] Power Management version 2 > > 0000:00:13.0 Ethernet controller: Realtek Semiconductor Co., Ltd. > RTL-8139/8139C/8139C+ (rev 10) > Subsystem: Realtek Semiconductor Co., Ltd. RT8139 > Flags: bus master, medium devsel, latency 64, IRQ 18 > I/O ports at e400 [size=256] > Memory at feb00000 (32-bit, non-prefetchable) [size=256] > Capabilities: [50] Power Management version 2 > > 0000:01:00.0 VGA compatible controller: ATI Technologies Inc Radeon > RV200 QW [Radeon 7500] (prog-if 00 [VGA]) > Subsystem: PC Partner Limited Radeon RV200 QW [Radeon 7500 LE] > Flags: bus master, stepping, 66MHz, medium devsel, latency 64, > IRQ 16 > Memory at a0000000 (32-bit, prefetchable) [size=128M] > I/O ports at d000 [size=256] > Memory at fe400000 (32-bit, non-prefetchable) [size=64K] > Expansion ROM at fe300000 [disabled] [size=128K] > Capabilities: [58] AGP version 2.0 > Capabilities: [50] Power Management version 2 > > -------- > > > "dmesg" output using kernel 2.4: > > > Linux version 2.4.27-2-386 ([EMAIL PROTECTED]) (gcc > version 3.3.5 (Debian 1:3.3.5-12)) #1 Mon May 16 16:47:51 JST 2005 > BIOS-provided physical RAM map: > BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) > BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) > BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved) > BIOS-e820: 0000000000100000 - 000000001ff40000 (usable) > BIOS-e820: 000000001ff40000 - 000000001ff50000 (ACPI data) > BIOS-e820: 000000001ff50000 - 0000000020000000 (ACPI NVS) > BIOS-e820: 00000000ff7c0000 - 0000000100000000 (reserved) > 511MB LOWMEM available. > found SMP MP-table at 000ff780 > hm, page 000ff000 reserved twice. > hm, page 00100000 reserved twice. > hm, page 000f0000 reserved twice. > hm, page 000f1000 reserved twice. > On node 0 totalpages: 130880 > zone(0): 4096 pages. > zone(1): 126784 pages. > zone(2): 0 pages. > ACPI: RSDP (v000 ACPIAM ) @ > 0x000f91a0 > ACPI: RSDT (v001 A M I OEMRSDT 0x09000424 MSFT 0x00000097) @ > 0x1ff40000 > ACPI: FADT (v002 A M I OEMFACP 0x09000424 MSFT 0x00000097) @ > 0x1ff40200 > ACPI: MADT (v001 A M I OEMAPIC 0x09000424 MSFT 0x00000097) @ > 0x1ff40300 > ACPI: OEMB (v001 A M I OEMBIOS 0x09000424 MSFT 0x00000097) @ > 0x1ff50040 > ACPI: DSDT (v001 A0008 A0008705 0x00000705 INTL 0x02002026) @ > 0x00000000 > ACPI: Local APIC address 0xfee00000 > ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) > Processor #0 Pentium(tm) Pro APIC version 16 > Using ACPI for processor (LAPIC) configuration information > Intel MultiProcessor Specification v1.1 > Virtual Wire compatibility mode. > OEM ID: ASUSTek Product ID: A7V880 APIC at: 0xFEE00000 > I/O APIC #1 Version 3 at 0xFEC00000. > Enabling APIC mode: Flat. Using 1 I/O APICs > Processors: 1 > Kernel command line: root=/dev/hda1 ro > Initializing CPU#0 > Detected 1533.449 MHz processor. > Console: colour VGA+ 80x25 > Calibrating delay loop... 3060.53 BogoMIPS > Memory: 511876k/523520k available (1069k kernel code, 11256k reserved, > 459k data, 96k init, 0k highmem) > Dentry cache hash table entries: 65536 (order: 7, 524288 bytes) > Inode cache hash table entries: 32768 (order: 6, 262144 bytes) > Mount cache hash table entries: 512 (order: 0, 4096 bytes) > Buffer cache hash table entries: 32768 (order: 5, 131072 bytes) > Page-cache hash table entries: 131072 (order: 7, 524288 bytes) > CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) > CPU: L2 Cache: 256K (64 bytes/line) > CPU: After generic, caps: 0383fbff c1c3fbff 00000000 00000000 > CPU: Common caps: 0383fbff c1c3fbff 00000000 00000000 > CPU: AMD Athlon(tm) XP 1800+ stepping 02 > Enabling fast FPU save and restore... done. > Enabling unmasked SIMD FPU exception support... done. > Checking 'hlt' instruction... OK. > Checking for popad bug... OK. > POSIX conformance testing by UNIFIX > enabled ExtINT on CPU#0 > ESR value before enabling vector: 00000080 > ESR value after enabling vector: 00000000 > ENABLING IO-APIC IRQs > Setting 1 in the phys_id_present_map > ....changing IO-APIC physical APIC ID to 1 ... ok. > init IO_APIC IRQs > IO-APIC (apicid-pin) 1-0, 1-17, 1-19, 1-23 not connected. > ...TIMER: vector=0x31 pin1=2 pin2=0 > number of MP IRQ sources: 25. > number of IO-APIC #1 registers: 24. > testing the IO APIC....................... > > IO APIC #1...... > ..... register #00: 01000000 > ........ : physical APIC id: 01 > ........ : Delivery Type: 0 > ........ : LTS : 0 > ..... register #01: 00178003 > ........ : max redirection entries: 0017 > ........ : PRQ implemented: 1 > ........ : IO APIC version: 0003 > ..... IRQ redirection table: > NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: > 00 000 00 1 0 0 0 0 0 0 00 > 01 001 01 0 0 0 0 0 1 1 39 > 02 001 01 0 0 0 0 0 1 1 31 > 03 001 01 0 0 0 0 0 1 1 41 > 04 001 01 0 0 0 0 0 1 1 49 > 05 001 01 0 0 0 0 0 1 1 51 > 06 001 01 0 0 0 0 0 1 1 59 > 07 001 01 0 0 0 0 0 1 1 61 > 08 001 01 0 0 0 0 0 1 1 69 > 09 001 01 0 0 0 0 0 1 1 71 > 0a 001 01 0 0 0 0 0 1 1 79 > 0b 001 01 0 0 0 0 0 1 1 81 > 0c 001 01 0 0 0 0 0 1 1 89 > 0d 001 01 0 0 0 0 0 1 1 91 > 0e 001 01 0 0 0 0 0 1 1 99 > 0f 001 01 0 0 0 0 0 1 1 A1 > 10 001 01 1 1 0 1 0 1 1 A9 > 11 000 00 1 0 0 0 0 0 0 00 > 12 001 01 1 1 0 1 0 1 1 B1 > 13 000 00 1 0 0 0 0 0 0 00 > 14 001 01 1 1 0 1 0 1 1 B9 > 15 001 01 1 1 0 1 0 1 1 C1 > 16 001 01 1 1 0 1 0 1 1 C9 > 17 000 00 1 0 0 0 0 0 0 00 > IRQ to pin mappings: > IRQ0 -> 0:2 > IRQ1 -> 0:1 > IRQ3 -> 0:3 > IRQ4 -> 0:4 > IRQ5 -> 0:5 > IRQ6 -> 0:6 > IRQ7 -> 0:7 > IRQ8 -> 0:8 > IRQ9 -> 0:9 > IRQ10 -> 0:10 > IRQ11 -> 0:11 > IRQ12 -> 0:12 > IRQ13 -> 0:13 > IRQ14 -> 0:14 > IRQ15 -> 0:15 > IRQ16 -> 0:16 > IRQ18 -> 0:18 > IRQ20 -> 0:20 > IRQ21 -> 0:21 > IRQ22 -> 0:22 > ..................................... done. > Using local APIC timer interrupts. > calibrating APIC timer ... > ...... CPU clock speed is 1533.4062 MHz. > ...... host bus clock speed is 266.6793 MHz. > cpu: 0, clocks: 2666793, slice: 1333396 > CPU0<T0:2666784,T1:1333376,D:12,S:1333396,C:2666793> > ACPI: Subsystem revision 20040326 > ACPI: Interpreter disabled. > PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=1 > PCI: Using configuration type 1 > PCI: Probing PCI hardware > PCI: ACPI tables contain no PCI IRQ routing entries > PCI: Probing PCI hardware (bus 00) > PCI: Using IRQ router default [1106/3227] at 00:11.0 > PCI->APIC IRQ transform: (B0,I15,P1) -> 20 > PCI->APIC IRQ transform: (B0,I15,P0) -> 20 > PCI->APIC IRQ transform: (B0,I16,P0) -> 21 > PCI->APIC IRQ transform: (B0,I16,P0) -> 21 > PCI->APIC IRQ transform: (B0,I16,P1) -> 21 > PCI->APIC IRQ transform: (B0,I16,P1) -> 21 > PCI->APIC IRQ transform: (B0,I16,P2) -> 21 > PCI->APIC IRQ transform: (B0,I17,P2) -> 22 > PCI->APIC IRQ transform: (B0,I19,P0) -> 18 > PCI->APIC IRQ transform: (B1,I0,P0) -> 16 > PCI: Via IRQ fixup for 00:10.3, from 3 to 5 > PCI: Via IRQ fixup for 00:10.2, from 3 to 5 > PCI: Via IRQ fixup for 00:10.1, from 11 to 5 > PCI: Via IRQ fixup for 00:10.0, from 11 to 5 > Linux NET4.0 for Linux 2.4 > Based upon Swansea University Computer Society NET3.039 > Initializing RT netlink socket > Starting kswapd > VFS: Disk quotas vdquot_6.5.1 > devfs: v1.12c (20020818) Richard Gooch ([EMAIL PROTECTED]) > devfs: boot_options: 0x0 > pty: 256 Unix98 ptys configured > Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT > SHARE_IRQ SERIAL_PCI enabled > ttyS00 at 0x03f8 (irq = 4) is a 16550A > COMX: driver version 0.85 (C) 1995-1999 ITConsult-Pro Co. <[EMAIL PROTECTED]> > RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize > Initializing Cryptographic API > NET4: Linux TCP/IP 1.0 for NET4.0 > IP: routing cache hash table of 4096 buckets, 32Kbytes > TCP: Hash tables configured (established 32768 bind 65536) > Linux IP multicast router 0.06 plus PIM-SM > RAMDISK: cramfs filesystem found at block 0 > RAMDISK: Loading 3692 blocks [1 disk] into ram disk... done. > Freeing initrd memory: 3692k freed > VFS: Mounted root (cramfs filesystem). > Freeing unused kernel memory: 96k freed > NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. > Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4 > ide: Assuming 33MHz system bus speed for PIO modes; override with > idebus=xx > ide: late registration of driver. > VP_IDE: IDE controller at PCI slot 00:0f.1 > VP_IDE: chipset revision 6 > VP_IDE: not 100% native mode: will probe irqs later > ide: Assuming 33MHz system bus speed for PIO modes; override with > idebus=xx > VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci00:0f.1 > ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio > ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:DMA > hda: Maxtor 6E040L0, ATA DISK drive > blk: queue e0825b60, I/O limit 4095Mb (mask 0xffffffff) > hdc: LITEON DVD-ROM LTD-165H, ATAPI CD/DVD-ROM drive > hdd: TSSTcorpCD/DVDW TS-H552U, ATAPI CD/DVD-ROM drive > ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 > ide1 at 0x170-0x177,0x376 on irq 15 > hda: attached ide-disk driver. > hda: 80293248 sectors (41110 MB) w/2048KiB Cache, CHS=79656/16/63, > UDMA(133) > Partition check: > /dev/ide/host0/bus0/target0/lun0: [PTBL] [4998/255/63] p1 p2 < p5 p6 > > Journalled Block Device driver loaded > kjournald starting. Commit interval 5 seconds > EXT3-fs: mounted filesystem with ordered data mode. > Adding Swap: 979924k swap-space (priority -1) > EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,1), internal journal > Real Time Clock Driver v1.10f > hdc: attached ide-cdrom driver. > hdc: ATAPI 48X DVD-ROM drive, 256kB Cache > Uniform CD-ROM driver Revision: 3.12 > hdd: attached ide-cdrom driver. > hdd: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33) > kjournald starting. Commit interval 5 seconds > EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,6), internal journal > EXT3-fs: mounted filesystem with ordered data mode. > lp: driver loaded but no devices found > 8139too Fast Ethernet driver 0.9.26 > eth0: RealTek RTL8139 at 0xe400, 00:40:95:32:59:60, IRQ 18 > eth0: Identified 8139 chip type 'RTL-8139C' > 8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004) > via82xx: Assuming DXS channels with 48k fixed sample rate. > Please try dxs_support=1 or dxs_support=4 option > and report if it works on your machine. > PCI: Setting latency timer of device 00:11.5 to 64 > ALSA ../alsa-kernel/pci/via82xx.c:582: codec_read: codec 0 is not valid > [0x107e5368] > ALSA ../alsa-kernel/pci/via82xx.c:582: codec_read: codec 0 is not valid > [0x107e5368] > ALSA ../alsa-kernel/pci/via82xx.c:582: codec_read: codec 0 is not valid > [0x107e5368] > ALSA ../alsa-kernel/pci/via82xx.c:582: codec_read: codec 0 is not valid > [0x107e5368] > usb.c: registered new driver usbdevfs > usb.c: registered new driver hub > ehci_hcd 00:10.4: VIA Technologies, Inc. USB 2.0 > ehci_hcd 00:10.4: irq 21, pci mem e09c9000 > usb.c: new USB bus registered, assigned bus number 1 > ehci_hcd 00:10.4: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29/2.4 > hub.c: USB hub found > hub.c: 8 ports detected > uhci.c: USB Universal Host Controller Interface driver v1.1 > uhci.c: USB UHCI at I/O 0xef40, IRQ 21 > usb.c: new USB bus registered, assigned bus number 2 > hub.c: USB hub found > hub.c: 2 ports detected > uhci.c: USB UHCI at I/O 0xef20, IRQ 21 > usb.c: new USB bus registered, assigned bus number 3 > hub.c: USB hub found > hub.c: 2 ports detected > uhci.c: USB UHCI at I/O 0xef00, IRQ 21 > usb.c: new USB bus registered, assigned bus number 4 > hub.c: USB hub found > hub.c: 2 ports detected > uhci.c: USB UHCI at I/O 0xeec0, IRQ 21 > usb.c: new USB bus registered, assigned bus number 5 > hub.c: USB hub found > hub.c: 2 ports detected > SCSI subsystem driver Revision: 1.00 > libata version 1.02 loaded. > sata_via version 0.20 > sata_via(00:0f.0): routed to hard irq line 4 > ata1: SATA max UDMA/133 cmd 0xEFF0 ctl 0xEFE6 bmdma 0xEF90 irq 20 > ata2: SATA max UDMA/133 cmd 0xEFA8 ctl 0xEFE2 bmdma 0xEF98 irq 20 > ata1: no device found (phy stat 00000000) > ata2: no device found (phy stat 00000000) > scsi0 : sata_via > scsi1 : sata_via > pci_hotplug: PCI Hot Plug PCI Core version: 0.5 > shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x1001 > hub.c: new USB device 00:10.0-1, assigned address 2 > usb.c: USB device 2 (vend/prod 0x3f0/0x7304) is not claimed by any > active driver. > pci_hotplug: PCI Hot Plug PCI Core version: 0.5 > pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x1001 > usb.c: registered new driver usblp > printer.c: usblp0: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 > vid 0x03F0 pid 0x7304 > printer.c: v0.13: USB Printer Device Class driver > eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 > apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16) > [drm] Initialized radeon 1.7.0 20020828 on minor 0 > [drm:radeon_unlock] *ERROR* Process 1400 using kernel context 0 > > -------- > > > "dmesg" output using kernel 2.6: > > > : 126784 pages, LIFO batch:16 > HighMem zone: 0 pages, LIFO batch:1 > DMI 2.3 present. > ACPI: RSDP (v000 ACPIAM ) @ > 0x000f91a0 > ACPI: RSDT (v001 A M I OEMRSDT 0x09000424 MSFT 0x00000097) @ > 0x1ff40000 > ACPI: FADT (v002 A M I OEMFACP 0x09000424 MSFT 0x00000097) @ > 0x1ff40200 > ACPI: MADT (v001 A M I OEMAPIC 0x09000424 MSFT 0x00000097) @ > 0x1ff40300 > ACPI: OEMB (v001 A M I OEMBIOS 0x09000424 MSFT 0x00000097) @ > 0x1ff50040 > ACPI: DSDT (v001 A0008 A0008705 0x00000705 INTL 0x02002026) @ > 0x00000000 > ACPI: PM-Timer IO Port: 0x808 > ACPI: Local APIC address 0xfee00000 > ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) > Processor #0 6:6 APIC version 16 > ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) > IOAPIC[0]: Assigned apic_id 1 > IOAPIC[0]: apic_id 1, version 3, address 0xfec00000, GSI 0-23 > ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) > ACPI: IRQ0 used by override. > ACPI: IRQ2 used by override. > ACPI: IRQ9 used by override. > Enabling APIC mode: Flat. Using 1 I/O APICs > Using ACPI (MADT) for SMP configuration information > Built 1 zonelists > Kernel command line: root=/dev/hda1 ro > Initializing CPU#0 > PID hash table entries: 2048 (order 11: 16384 bytes) > Detected 1533.339 MHz processor. > Using pmtmr for high-res timesource > Console: colour VGA+ 80x25 > Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) > Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) > Memory: 510708k/523520k available (1536k kernel code, 12028k reserved, > 697k data, 148k init, 0k highmem) > Checking if this processor honours the WP bit even in supervisor mode... > Ok. > Calibrating delay loop... 3031.04 BogoMIPS > Security Scaffold v1.0.0 initialized > Mount-cache hash table entries: 512 (order: 0, 4096 bytes) > CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000 > CPU: After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000 > CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) > CPU: L2 Cache: 256K (64 bytes/line) > CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000020 > Intel machine check architecture supported. > Intel machine check reporting enabled on CPU#0. > CPU: AMD Athlon(tm) XP 1800+ stepping 02 > Enabling fast FPU save and restore... done. > Enabling unmasked SIMD FPU exception support... done. > Checking 'hlt' instruction... OK. > enabled ExtINT on CPU#0 > ESR value before enabling vector: 00000080 > ESR value after enabling vector: 00000000 > ENABLING IO-APIC IRQs > init IO_APIC IRQs > IO-APIC (apicid-pin) 1-0, 1-16, 1-17, 1-18, 1-19, 1-20, 1-21, 1-22, > 1-23 not connected. > ...TIMER: vector=0x31 pin1=2 pin2=-1 > Using local APIC timer interrupts. > calibrating APIC timer ... > ...... CPU clock speed is 1533.0239 MHz. > ...... host bus clock speed is 266.0650 MHz. > checking if image is initramfs...it isn't (ungzip failed); looks like an > initrd > Freeing initrd memory: 4468k freed > NET: Registered protocol family 16 > PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=1 > PCI: Using configuration type 1 > mtrr: v2.0 (20020519) > ACPI: Subsystem revision 20040326 > ACPI: Interpreter enabled > ACPI: Using IOAPIC for interrupt routing > ACPI: PCI Root Bridge [PCI0] (00:00) > PCI: Probing PCI hardware (bus 00) > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] > ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 14 15) > ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 5 7 10 11 14 15) > ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *10 11 14 15) > ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 7 10 11 14 15) > ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 14 15) *0, disabled. > ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 14 15) *0, disabled. > ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 14 15) *0, disabled. > ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 14 15) *0, disabled. > Linux Plug and Play Support v0.97 (c) Adam Belay > PnPBIOS: Scanning system for PnP BIOS support... > PnPBIOS: Found PnP BIOS installation structure at 0xc00f48a0 > PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x548a, dseg 0xf0000 > PNPBIOS fault.. attempting recovery. > PnPBIOS: Warning! Your PnP BIOS caused a fatal error. Attempting to > continue > PnPBIOS: You may need to reboot with the "nobiospnp" option to operate > stably > PnPBIOS: Check with your vendor for an updated BIOS > PnPBIOS: get_dev_node: unexpected status 0x28 > PnPBIOS: 6 nodes reported by PnP BIOS; 6 recorded by driver > PCI: Using ACPI for IRQ routing > ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 18 (level, low) -> IRQ 169 > ACPI: PCI interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 177 > ACPI: PCI interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 177 > ACPI: PCI interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 185 > ACPI: PCI interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 185 > ACPI: PCI interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 185 > ACPI: PCI interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 185 > ACPI: PCI interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 185 > ACPI: PCI interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 193 > ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 201 > number of MP IRQ sources: 15. > number of IO-APIC #1 registers: 24. > testing the IO APIC....................... > IO APIC #1...... > ..... register #00: 01000000 > ........ : physical APIC id: 01 > ........ : Delivery Type: 0 > ........ : LTS : 0 > ..... register #01: 00178003 > ........ : max redirection entries: 0017 > ........ : PRQ implemented: 1 > ........ : IO APIC version: 0003 > ..... IRQ redirection table: > NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: > 00 000 00 1 0 0 0 0 0 0 00 > 01 001 01 0 0 0 0 0 1 1 39 > 02 001 01 0 0 0 0 0 1 1 31 > 03 001 01 0 0 0 0 0 1 1 41 > 04 001 01 0 0 0 0 0 1 1 49 > 05 001 01 0 0 0 0 0 1 1 51 > 06 001 01 0 0 0 0 0 1 1 59 > 07 001 01 0 0 0 0 0 1 1 61 > 08 001 01 0 0 0 0 0 1 1 69 > 09 001 01 0 1 0 1 0 1 1 71 > 0a 001 01 0 0 0 0 0 1 1 79 > 0b 001 01 0 0 0 0 0 1 1 81 > 0c 001 01 0 0 0 0 0 1 1 89 > 0d 001 01 0 0 0 0 0 1 1 91 > 0e 001 01 0 0 0 0 0 1 1 99 > 0f 001 01 0 0 0 0 0 1 1 A1 > 10 001 01 1 1 0 1 0 1 1 C9 > 11 000 00 1 0 0 0 0 0 0 00 > 12 001 01 1 1 0 1 0 1 1 A9 > 13 000 00 1 0 0 0 0 0 0 00 > 14 001 01 1 1 0 1 0 1 1 B1 > 15 001 01 1 1 0 1 0 1 1 B9 > 16 001 01 1 1 0 1 0 1 1 C1 > 17 000 00 1 0 0 0 0 0 0 00 > Using vector-based indexing > IRQ to pin mappings: > IRQ0 -> 0:2 > IRQ1 -> 0:1 > IRQ3 -> 0:3 > IRQ4 -> 0:4 > IRQ5 -> 0:5 > IRQ6 -> 0:6 > IRQ7 -> 0:7 > IRQ8 -> 0:8 > IRQ9 -> 0:9 > IRQ10 -> 0:10 > IRQ11 -> 0:11 > IRQ12 -> 0:12 > IRQ13 -> 0:13 > IRQ14 -> 0:14 > IRQ15 -> 0:15 > IRQ201 -> 0:16 > IRQ169 -> 0:18 > IRQ177 -> 0:20 > IRQ185 -> 0:21 > IRQ193 -> 0:22 > ..................................... done. > VFS: Disk quotas dquot_6.5.1 > Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) > devfs: 2004-01-31 Richard Gooch ([EMAIL PROTECTED]) > devfs: boot_options: 0x0 > Initializing Cryptographic API > PCI: Via IRQ fixup for 0000:00:10.3, from 3 to 9 > PCI: Via IRQ fixup for 0000:00:10.2, from 3 to 9 > PCI: Via IRQ fixup for 0000:00:10.1, from 11 to 9 > PCI: Via IRQ fixup for 0000:00:10.0, from 11 to 9 > PCI: Via IRQ fixup for 0000:00:11.5, from 10 to 1 > isapnp: Scanning for PnP cards... > isapnp: No Plug & Play device found > Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing > enabled > ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A > RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize > serio: i8042 AUX port at 0x60,0x64 irq 12 > serio: i8042 KBD port at 0x60,0x64 irq 1 > input: AT Translated Set 2 keyboard on isa0060/serio0 > NET: Registered protocol family 2 > IP: routing cache hash table of 4096 buckets, 32Kbytes > TCP: Hash tables configured (established 32768 bind 65536) > NET: Registered protocol family 8 > NET: Registered protocol family 20 > ACPI: (supports S0 S1 S3 S4 S5) > RAMDISK: cramfs filesystem found at block 0 > RAMDISK: Loading 4468 blocks [1 disk] into ram disk... done. > VFS: Mounted root (cramfs filesystem) readonly. > Freeing unused kernel memory: 148k freed > vesafb: probe of vesafb0 failed with error -6 > NET: Registered protocol family 1 > SCSI subsystem initialized > libata version 1.02 loaded. > Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 > ide: Assuming 33MHz system bus speed for PIO modes; override with > idebus=xx > VP_IDE: IDE controller at PCI slot 0000:00:0f.1 > ACPI: PCI interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 177 > VP_IDE: chipset revision 6 > VP_IDE: not 100% native mode: will probe irqs later > VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1 > ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio > ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:DMA > hda: Maxtor 6E040L0, ATA DISK drive > Using anticipatory io scheduler > ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 > hda: max request size: 128KiB > hda: 80293248 sectors (41110 MB) w/2048KiB Cache, CHS=65535/16/63, > UDMA(133) > /dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 p6 > > hdc: LITEON DVD-ROM LTD-165H, ATAPI CD/DVD-ROM drive > hdd: TSSTcorpCD/DVDW TS-H552U, ATAPI CD/DVD-ROM drive > ide1 at 0x170-0x177,0x376 on irq 15 > EXT3-fs: INFO: recovery required on readonly filesystem. > EXT3-fs: write access will be enabled during recovery. > kjournald starting. Commit interval 5 seconds > EXT3-fs: recovery complete. > EXT3-fs: mounted filesystem with ordered data mode. > Adding 979924k swap on /dev/hda5. Priority:-1 extents:1 > EXT3 FS on hda1, internal journal > hdc: ATAPI 48X DVD-ROM drive, 256kB Cache > Uniform CD-ROM driver Revision: 3.20 > hdd: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33) > input: PS/2 Logitech Mouse on isa0060/serio1 > Capability LSM initialized > mice: PS/2 mouse device common for all mice > ts: Compaq touchscreen protocol output > kjournald starting. Commit interval 5 seconds > EXT3 FS on hda6, internal journal > EXT3-fs: mounted filesystem with ordered data mode. > ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 18 (level, low) -> IRQ 169 > sk98lin: Network Device Driver v6.23 > (C)Copyright 1999-2004 Marvell(R). > ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 18 (level, low) -> IRQ 169 > eth0: Yukon Gigabit Ethernet 10/100/1000Base-T Adapter > PrefPort:A RlmtMode:Check Link State > sata_via version 0.20 > ACPI: PCI interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 177 > sata_via(0000:00:0f.0): routed to hard irq line 10 > ata1: SATA max UDMA/133 cmd 0xEFF0 ctl 0xEFE6 bmdma 0xEF90 irq 177 > ata2: SATA max UDMA/133 cmd 0xEFA8 ctl 0xEFE2 bmdma 0xEF98 irq 177 > ata1: no device found (phy stat 00000000) > scsi0 : sata_via > ata2: no device found (phy stat 00000000) > scsi1 : sata_via > usbcore: registered new driver usbfs > usbcore: registered new driver hub > USB Universal Host Controller Interface driver v2.2 > ACPI: PCI interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 185 > uhci_hcd 0000:00:10.0: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 > Controller > uhci_hcd 0000:00:10.0: irq 185, io base 0000eec0 > uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1 > hub 1-0:1.0: USB hub found > hub 1-0:1.0: 2 ports detected > ACPI: PCI interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 185 > uhci_hcd 0000:00:10.1: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 > Controller (#2) > uhci_hcd 0000:00:10.1: irq 185, io base 0000ef00 > uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2 > hub 2-0:1.0: USB hub found > hub 2-0:1.0: 2 ports detected > ACPI: PCI interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 185 > uhci_hcd 0000:00:10.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 > Controller (#3) > uhci_hcd 0000:00:10.2: irq 185, io base 0000ef20 > uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3 > hub 3-0:1.0: USB hub found > hub 3-0:1.0: 2 ports detected > ACPI: PCI interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 185 > uhci_hcd 0000:00:10.3: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 > Controller (#4) > uhci_hcd 0000:00:10.3: irq 185, io base 0000ef40 > uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4 > hub 4-0:1.0: USB hub found > hub 4-0:1.0: 2 ports detected > usb 1-1: new full speed USB device using address 2 > ACPI: PCI interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 185 > ehci_hcd 0000:00:10.4: VIA Technologies, Inc. USB 2.0 > ehci_hcd 0000:00:10.4: irq 185, pci mem e08a1000 > ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5 > ehci_hcd 0000:00:10.4: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10 > hub 5-0:1.0: USB hub found > hub 5-0:1.0: 8 ports detected > drivers/usb/class/usblp.c: can't set desired altsetting 0 on interface 0 > usblp: probe of 1-1:1.0 failed with error -5 > usbcore: registered new driver usblp > drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver > usb 1-1: USB disconnect, address 2 > via82xx: Assuming DXS channels with 48k fixed sample rate. > Please try dxs_support=1 or dxs_support=4 option > and report if it works on your machine. > ACPI: PCI interrupt 0000:00:11.5[C] -> GSI 22 (level, low) -> IRQ 193 > PCI: Setting latency timer of device 0000:00:11.5 to 64 > codec_read: codec 0 is not valid [0x107e5368] > codec_read: codec 0 is not valid [0x107e5368] > codec_read: codec 0 is not valid [0x107e5368] > codec_read: codec 0 is not valid [0x107e5368] > usb 1-1: new full speed USB device using address 3 > drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 3 if 0 > alt 0 proto 2 vid 0x03F0 pid 0x7304 > Linux agpgart interface v0.100 (c) Dave Jones > agpgart: Detected VIA KT880 chipset > agpgart: Maximum main memory to use for agp memory: 439M > agpgart: AGP aperture is 256M @ 0xe0000000 > cpci_hotplug: CompactPCI Hot Plug Core version: 0.2 > pci_hotplug: PCI Hot Plug PCI Core version: 0.5 > pciehp: PCI Express Hot Plug Controller Driver version: 0.4 > shpchp: shpc_init : shpc_cap_offset == 0 > shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 > Real Time Clock Driver v1.12 > NET: Registered protocol family 17 > eth0: network connection up using port A > speed: 100 > autonegotiation: yes > duplex mode: full > flowctrl: none > irq moderation: disabled > scatter-gather: enabled > lp: driver loaded but no devices found > NET: Registered protocol family 10 > Disabled Privacy Extensions on device c02fc1a0(lo) > IPv6 over IPv4 tunneling driver > [drm] Initialized radeon 1.11.0 20020828 on minor 0: ATI Technologies > Inc Radeon RV200 QW [Radeon 7500] > agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0. > agpgart: Device is in legacy mode, falling back to 2.x > agpgart: Putting AGP V2 device at 0000:00:00.0 into 0x mode > agpgart: Putting AGP V2 device at 0000:01:00.0 into 0x mode > eth0: no IPv6 routers present > > > -- System Information: > Debian Release: 3.1 > Architecture: i386 (i686) > Kernel: Linux 2.4.27-2-386 > Locale: [EMAIL PROTECTED], [EMAIL PROTECTED] (charmap=ISO-8859-15) > > Versions of packages kernel-image-2.6.8-2-k7 depends on: > ii coreutils [fileutils] 5.2.1-2 The GNU core utilities > ii initrd-tools 0.1.81.1 tools to create initrd image for > p > ii module-init-tools 3.2-pre1-2 tools for managing Linux kernel > mo > > -- no debconf information > > > -- > To UNSUBSCRIBE, email to [EMAIL PROTECTED] > with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED] -- Horms -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
