Hallo, from what I understand, Your Nic is already working in the sense, the kernel detects it. As soon as Your kernel discovers "eth0" You've no longer any need to upgrade the kernel in order to get the network running. Instead try looking what went wrong with Your basic network configuration, that is, "ifconfig" and "route" together with their man pages are Your friends at the moment. Additionally You might want to have a look into /etc/network/interfaces (it also comes with a nice man page). As long as Your NIC is not setup by dhcp, You'll have to add the defaultrout through Your gateway by hand. IIRC the command there ist route add default gw "router-ip-address" but I could be wrong there. The steps, You should go through is a) get the interface correct so You can ping local devices including Your router b) get the route right to be able to ping some internet connected computer (by IP address!) c) get dns running (in that case, You'll have to look into /etv/resolv.conf). Best regards, js
>Hi!Jonathan, > >Thanks your reply! > >It's said that the NIC network cards of EPOX-8rda3g MB would be in function under kernel 2.4.20. >should I upgrade the current woody kernel to sarge and thus to set up networking and complet my debian installation? > >then from sarge , upgrading debian to Kernel 2.6.3? >should I download the kernel at (http://www.kernel.org)to make compilings?or elsewhere? > >Best regards! > >Tom >7/3/2004 >---------------------------------------------------------- > > >======================================================================== >To: [EMAIL PROTECTED] >Subject: Re: base system, no x windows yet,HOW? >From: Jonathan Schmitt <[EMAIL PROTECTED]> >Date: Fri, 5 Mar 2004 18:12:07 +0100 >In-reply-to: <[EMAIL PROTECTED]> >Message-id: <[EMAIL PROTECTED]> >Old-return-path: <[EMAIL PROTECTED]> >References: <[EMAIL PROTECTED]> >User-agent: KMail/1.6 > >Hallo, > >>At first I ventured into debian installation ( via networking)again, >>the embeded LAN chips(RTL8201BL , RTL8101L) of current EPOX-8RDA3G >> motherboard (nforce2 Ultra 400 +MCP chipsets) can't be detected whatever >> kernel driver modules I set on. > >There is one driver in the current 2.6.3 Kernel, it's called "reverese >engineered nforce ethernet support" which is most likely, what You've got. > >>Now it's only a base system, I can login under console.... >>no x windows yet , what left packages should I download & install under >>console ?is it possible to make networking chips work and make rest of >>installation via network and upgrade kernel to latest 2.6.3? and how to do it >>under console with commands? > >The general idea would be to first install 2.6.3 by hand and have networking >afterwards. However it is NOT suggested to do so, especially not with debian >woody, as debian woody is not prepared for 2.6 series. In that case, it is >suggested to update to debian testing (sarge) which is prepared. >downloading kernel sources by hand will not do the trick. You will need at >least the bzip2 package along with the ncurses5-dev to run at least >menuconfig (or face some sort of hell using make config). To find out, mark a >2.4 kernel source in dselect and watch the dependencies it discoveres. >You could simplify Your live by getting to the next discounter and by a >(presumably 10$) Realtek 8139 ethernet board, solving Your problems. >If You do not know how to recompile a kernel, You should surf to www.tldp.org >and look there (or the appropriate document at debian.org, telling You how to >do it the debian way). >Once again, do NOT use 2.6 with woody unless You exactly know, what You're >doing. > js > >>do help me out! >>do write me back ASAP! >these are considered rather unpolite... >-- >I've got a very bad feeling about this. >-- Han Solo > > >-- >To UNSUBSCRIBE, email to [EMAIL PROTECTED] >with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED] > > > -- ... TheysaidDoyouseethebiggreenglowinthedarkhouseuponthehill?andIsaidYesIsee thebiggreenglowinthedarkhouseuponthehillTheresabigdarkforestbetweenmeandthe biggreenglowinthedarkhouseuponthehillandalittleoldladyridingonaHoovervacuum cleanersayingIllgetyoumyprettyandyourlittledogTototoo ... I don't even *HAVE* a dog Toto... -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
