On 9/14/23 03:17, Vincent Lefevre wrote:
On 2023-09-13 20:52:43 -0700, David Christensen wrote:
On 9/13/23 04:54, Vincent Lefevre wrote:
Hi,
I need to use ddrescue on the root partition of my laptop.
So I need to have the root partition mounted in read-only mode.
How can I do that?
Note that "mount -o remount,ro /" gives an error "mount point is busy"
apparently because various log files are open in write mode.
Using the recovery mode via GRUB (which mounts / in read-only mode)
is useless because the system remounts it later as rw.
Or is there a way to force a remount in read-only mode?
(I could probably trigger a disk error to make the kernel remount /
as read-only, but well...)
What symptom(s) is your laptop exhibiting that make you think that you need
to use ddrescue(1) on the root partition?
I get UNC errors like
2023-09-10T11:50:59.858670+0200 zira kernel: ata1.00: exception Emask 0x0 SAct
0xc00 SErr 0x40000 action 0x0
2023-09-10T11:51:00.117366+0200 zira kernel: ata1.00: irq_stat 0x40000008
2023-09-10T11:51:00.117431+0200 zira kernel: ata1: SError: { CommWake }
2023-09-10T11:51:00.117474+0200 zira kernel: ata1.00: failed command: READ
FPDMA QUEUED
2023-09-10T11:51:00.117511+0200 zira kernel: ata1.00: cmd
60/00:50:b8:12:c5/02:00:1f:00:00/40 tag 10 ncq dma 262144 in
res
41/40:00:90:13:c5/00:02:1f:00:00/00 Emask 0x409 (media error) <F>
2023-09-10T11:51:00.117537+0200 zira kernel: ata1.00: status: { DRDY ERR }
2023-09-10T11:51:00.117560+0200 zira kernel: ata1.00: error: { UNC }
2023-09-10T11:51:00.117583+0200 zira kernel: ata1.00: supports DRM functions
and may not be fully accessible
2023-09-10T11:51:00.117614+0200 zira kernel: ata1.00: supports DRM functions
and may not be fully accessible
2023-09-10T11:51:00.117651+0200 zira kernel: ata1.00: configured for UDMA/133
2023-09-10T11:51:00.117681+0200 zira kernel: sd 0:0:0:0: [sda] tag#10 FAILED
Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=0s
2023-09-10T11:51:00.117953+0200 zira kernel: sd 0:0:0:0: [sda] tag#10 Sense Key
: Medium Error [current]
2023-09-10T11:51:00.118165+0200 zira kernel: sd 0:0:0:0: [sda] tag#10 Add.
Sense: Unrecovered read error - auto reallocate failed
2023-09-10T11:51:00.118366+0200 zira kernel: sd 0:0:0:0: [sda] tag#10 CDB:
Read(10) 28 00 1f c5 12 b8 00 02 00 00
2023-09-10T11:51:00.118557+0200 zira kernel: I/O error, dev sda, sector
533009296 op 0x0:(READ) flags 0x80700 phys_seg 37 prio class 2
2023-09-10T11:51:00.118582+0200 zira kernel: ata1: EH complete
2023-09-10T11:51:00.118608+0200 zira kernel: ata1.00: Enabling
discard_zeroes_data
What is the make and model of the laptop?
What is the make and model of the disk drive?
When and where do you see the above error messages?
and after these errors, the kernel remount the root partition as
read-only.
That sounds like a reasonable boot loader response to an OS drive error
during boot.
Due to these errors, some files are unreadable.
badblocks says that there are 25252 bad blocks.
I'm using ddrescue before doing anything else (mainly in case things
would go worse), but I would essentially be interested in knowing
which files are affected.
Was the computer working correctly in the past?
When did you first notice the error messages? What was the computer
doing at the time?
Did you make any changes to the computer (hardware, software,
configuration, apps, other) immediately prior to the start of the error
messages?
Does the computer now generate error messages? Consistently? What is
it doing when the error messages are generated?
The laptop is in the process of being replaced, so I don't plan to
replace the disk (unless things get really wrong).
Then perhaps you should get the replacement and decommission the olde
laptop (remove the disk drive, have it shredded, and resell, recycle, or
reuse the laptop).
Have you read the "GNU ddrescue Manual"?
https://www.gnu.org/software/ddrescue/manual/ddrescue_manual.html
Yes.
Okay.
It sounds like you are booting a computer with OS drive issues and
attempting to use that computer to trouble-shoot itself. If the issue
seems minor, or is familiar, I might do the same. Otherwise, I do one
or more of the following:
* Browse the disk drive manufacturer's web site for a bootable drive
diagnostic tool. If available, I download the tool, burn it to media,
and use it to trouble-shoot the disk drive.
* I install Debian with Xfce onto a good USB 3.0 flash drive. I then
install my favorite system administration and trouble-shooting packages.
I boot the USB flash drive in suitable computers and use it to
trouble-shoot the computer and/or components (including disk drives).
* I remove the disk from the computer, install it another computer, and
use the other computer to trouble-shoot the disk.
David
