I cannot catch the user space output on the broken machine
To get netconsole going I have edited
/usr/share/initramfs-tools/scripts/init-top/udev
First to load the network module.
2nd to load the netconsole:
---snip----
echo modprobe comes next ...
sleep 9
set -x
modprobe r8169
lsmod|grep r8169
modprobe netconsole
netconsole="6666@192.168.178.62/enp3s0,6666@192.168.178.54/04:92:26:d9:4e:9e"
res=$?
if [ "$res" -eq 0 ]; then
echo modprobe worked
else
echo modprobe failed eith $res
fi
---snap----
The netconsole output from the kernel:
[ 28.109866] r8169 0000:03:00.0: firmware: direct-loading firmware
rtl_nic/rtl8125b-2.fw
[ 28.141085] RTL8226B_RTL8221B 2.5Gbps PHY r8169-0-300:00: attached PHY
driver (mii_bus:phy_addr=r8169-0-300:00, irq=MAC)
[ 28.341236] r8169 0000:03:00.0 enp3s0: Link is Down
[ 30.013941] r8169 0000:03:00.0 enp3s0: Link is Up - 100Mbps/Full - flow
control rx/tx
[ 30.014760] IPv6: ADDRCONF(NETDEV_CHANGE): enp3s0: link becomes ready
[ 30.021222] printk: console [netcon0] enabled
[ 30.024682] netconsole: network logging started
[ 68.102701] input: Sleep Button as
/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input0
[ 68.102771] ACPI: button: Sleep Button [SLPB]
[ 68.102874] input: Power Button as
/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
[ 68.102964] ACPI: button: Power Button [PWRB]
[ 68.103014] input: Power Button as
/devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 68.103079] ACPI: button: Power Button [PWRF]
[ 68.158125] i801_smbus 0000:00:1f.4: SMBus using PCI interrupt
[ 68.160436] i2c i2c-0: 4/4 memory slots populated (from DMI)
[ 68.160795] i2c i2c-0: Successfully instantiated SPD at 0x50
[ 68.161131] i2c i2c-0: Successfully instantiated SPD at 0x51
[ 68.161513] i2c i2c-0: Successfully instantiated SPD at 0x52
[ 68.161895] i2c i2c-0: Successfully instantiated SPD at 0x53
[ 68.166974] ACPI: bus type USB registered
[ 68.166994] usbcore: registered new interface driver usbfs
[ 68.166998] usbcore: registered new interface driver hub
[ 68.167054] usbcore: registered new device driver usb
[ 68.170281] SCSI subsystem initialized
[ 68.183217] cryptd: max_cpu_qlen set to 1000
[ 68.183493] ACPI: bus type drm_connector registered
[ 68.195886] nvme nvme0: pci function 0000:02:00.0
[ 68.196051] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 68.196193] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus
number 1
[ 68.196443] nvme nvme1: pci function 0000:04:00.0
[ 68.197314] libata version 3.00 loaded.
[ 68.197503] xhci_hcd 0000:00:14.0: hcc params 0x20007fc1 hci version 0x120
quirks 0x0000000200009810
[ 68.197931] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 68.198112] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus
number 2
[ 68.198305] xhci_hcd 0000:00:14.0: Host supports USB 3.2 Enhanced SuperSpeed
[ 68.198544] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002,
bcdDevice= 6.04
[ 68.198762] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 68.198986] usb usb1: Product: xHCI Host Controller
[ 68.199214] usb usb1: Manufacturer: Linux 6.4.0-3-amd64 xhci-hcd
[ 68.199452] usb usb1: SerialNumber: 0000:00:14.0
[ 68.199775] AVX2 version of gcm_enc/dec engaged.
[ 68.200044] AES CTR mode by8 optimization enabled
[ 68.200049] hub 1-0:1.0: USB hub found
[ 68.200580] hub 1-0:1.0: 16 ports detected
[ 68.200680] nvme nvme0: missing or invalid SUBNQN field.
[ 68.200681] nvme nvme1: missing or invalid SUBNQN field.
[ 68.200757] nvme nvme1: Shutdown timeout set to 10 seconds
[ 68.202337] nvme nvme1: 8/0/0 default/read/poll queues
[ 68.203130] nvme nvme1: Ignoring bogus Namespace Identifiers
[ 68.204269] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003,
bcdDevice= 6.04
[ 68.204570] usb usb2: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 68.204625] nvme1n1: p1 p2 p3 p4 p5 p6
[ 68.204875] usb usb2: Product: xHCI Host Controller
[ 68.205508] usb usb2: Manufacturer: Linux 6.4.0-3-amd64 xhci-hcd
[ 68.205837] usb usb2: SerialNumber: 0000:00:14.0
[ 68.206236] hub 2-0:1.0: USB hub found
[ 68.206585] hub 2-0:1.0: 6 ports detected
[ 68.224577] nvme nvme0: 12/0/0 default/read/poll queues
[ 68.229866] nvme0n1: p1
[ 68.235064] ahci 0000:00:17.0: version 3.0
[ 68.245738] ahci 0000:00:17.0: AHCI 0001.0301 32 slots 6 ports 6 Gbps 0x3f
impl SATA mode
[ 68.246127] ahci 0000:00:17.0: flags: 64bit ncq sntf clo only pio slum part
ems deso sadm sds
[ 68.309605] scsi host0: ahci
[ 68.310264] scsi host1: ahci
[ 68.310866] scsi host2: ahci
[ 68.311437] scsi host3: ahci
[ 68.312021] scsi host4: ahci
[ 68.312594] scsi host5: ahci
[ 68.313025] ata1: SATA max UDMA/133 abar m2048@0x81402000 port 0x81402100
irq 148
[ 68.313454] ata2: SATA max UDMA/133 abar m2048@0x81402000 port 0x81402180
irq 148
[ 68.313869] ata3: SATA max UDMA/133 abar m2048@0x81402000 port 0x81402200
irq 148
[ 68.314272] ata4: SATA max UDMA/133 abar m2048@0x81402000 port 0x81402280
irq 148
[ 68.314665] ata5: SATA max UDMA/133 abar m2048@0x81402000 port 0x81402300
irq 148
[ 68.315049] ata6: SATA max UDMA/133 abar m2048@0x81402000 port 0x81402380
irq 148
[ 68.461091] usb 1-3: new low-speed USB device number 2 using xhci_hcd
[ 68.549897] Console: switching to colour dummy device 80x25
[ 68.550154] i915 0000:00:02.0: vgaarb: changed VGA decodes:
olddecodes=io+mem,decodes=none:owns=io+mem
[ 68.550195] i915 0000:00:02.0: firmware: direct-loading firmware
i915/kbl_dmc_ver1_04.bin
[ 68.550693] i915 0000:00:02.0: [drm] Finished loading DMC firmware
i915/kbl_dmc_ver1_04.bin (v1.4)
[ 68.552138] [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0
[ 68.552868] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no
post: no)
[ 68.553270] input: Video Bus as
/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input3
[ 68.565172] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes
[ 68.628180] ata2: SATA link down (SStatus 4 SControl 300)
[ 68.628223] ata5: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 68.628265] ata6: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 68.629030] ata5.00: ATA-9: CT480BX300SSD1, M2CR010, max UDMA/133
[ 68.629074] ata6.00: ATA-9: CT480BX300SSD1, M2CR010, max UDMA/133
[ 68.629090] ata5.00: 937703088 sectors, multi 1: LBA48 NCQ (depth 32), AA
[ 68.629174] ata6.00: 937703088 sectors, multi 1: LBA48 NCQ (depth 32), AA
[ 68.629625] ata5.00: Features: Dev-Sleep
[ 68.629641] usb 1-3: New USB device found, idVendor=045e, idProduct=00db,
bcdDevice= 1.73
[ 68.629657] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 68.629664] usb 1-3: Product: Natural® Ergonomic Keyboard 4000
[ 68.629670] usb 1-3: Manufacturer: Microsoft
[ 68.629705] ata6.00: Features: Dev-Sleep
[ 68.630350] ata6.00: configured for UDMA/133
[ 68.630371] ata5.00: configured for UDMA/133
[ 68.631892] ata4: SATA link down (SStatus 4 SControl 300)
[ 68.631934] ata3: SATA link down (SStatus 4 SControl 300)
[ 68.631952] ata1: SATA link down (SStatus 4 SControl 300)
[ 68.633155] scsi 4:0:0:0: Direct-Access ATA CT480BX300SSD1 010
PQ: 0 ANSI: 5
[ 68.633604] scsi 5:0:0:0: Direct-Access ATA CT480BX300SSD1 010
PQ: 0 ANSI: 5
[ 68.635890] hid: raw HID events driver (C) Jiri Kosina
[ 68.638070] sd 5:0:0:0: [sda] 937703088 512-byte logical blocks: (480 GB/447
GiB)
[ 68.638076] sd 5:0:0:0: [sda] 4096-byte physical blocks
[ 68.638092] sd 5:0:0:0: [sda] Write Protect is off
[ 68.638098] sd 5:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 68.638115] sd 5:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 68.638134] sd 5:0:0:0: [sda] Preferred minimum I/O size 4096 bytes
[ 68.638161] sd 4:0:0:0: [sdb] 937703088 512-byte logical blocks: (480 GB/447
GiB)
[ 68.638190] sd 4:0:0:0: [sdb] 4096-byte physical blocks
[ 68.638252] sd 4:0:0:0: [sdb] Write Protect is off
[ 68.638258] sd 4:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 68.638304] sd 4:0:0:0: [sdb] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 68.638324] sd 4:0:0:0: [sdb] Preferred minimum I/O size 4096 bytes
[ 68.639878] sda: sda1
[ 68.639926] sd 5:0:0:0: [sda] Attached SCSI disk
[ 68.640097] sdb: sdb1
[ 68.640139] sd 4:0:0:0: [sdb] Attached SCSI disk
[ 68.647111] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes
[ 68.654680] usbcore: registered new interface driver usbhid
[ 68.654685] usbhid: USB HID core driver
[ 68.657704] input: Microsoft Natural® Ergonomic Keyboard 4000 as
/devices/pci0000:00/0000:00:14.0/usb1/1-3/1-3:1.0/0003:045E:00DB.0001/input/input4
[ 68.659288] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes
[ 68.717243] microsoft 0003:045E:00DB.0001: input,hidraw0: USB HID v1.11
Keyboard [Microsoft Natural® Ergonomic Keyboard 4000] on
usb-0000:00:14.0-3/input0
[ 68.717576] input: Microsoft Natural® Ergonomic Keyboard 4000 as
/devices/pci0000:00/0000:00:14.0/usb1/1-3/1-3:1.1/0003:045E:00DB.0002/input/input5
[ 68.757125] usb 1-4: new full-speed USB device number 3 using xhci_hcd
[ 68.777340] microsoft 0003:045E:00DB.0002: input,hidraw1: USB HID v1.11
Device [Microsoft Natural® Ergonomic Keyboard 4000] on usb-0000:00:14.0-3/input1
[ 68.908309] usb 1-4: New USB device found, idVendor=145f, idProduct=026d,
bcdDevice= 1.00
[ 68.908339] usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 68.908354] usb 1-4: Product: GXT 144 Gaming Mouse
[ 68.908364] usb 1-4: Manufacturer: SINOWEALTH
[ 68.912256] input: SINOWEALTH GXT 144 Gaming Mouse as
/devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4:1.0/0003:145F:026D.0003/input/input6
[ 68.912547] hid-generic 0003:145F:026D.0003: input,hidraw2: USB HID v1.11
Mouse [SINOWEALTH GXT 144 Gaming Mouse] on usb-0000:00:14.0-4/input0
[ 68.917393] input: SINOWEALTH GXT 144 Gaming Mouse Keyboard as
/devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4:1.1/0003:145F:026D.0004/input/input7
[ 68.977606] hid-generic 0003:145F:026D.0004: input,hiddev0,hidraw3: USB HID
v1.11 Keyboard [SINOWEALTH GXT 144 Gaming Mouse] on usb-0000:00:14.0-4/input1
[ 69.105124] usb 1-9: new high-speed USB device number 4 using xhci_hcd
[ 69.254887] usb 1-9: New USB device found, idVendor=05e3, idProduct=0608,
bcdDevice=60.90
[ 69.254915] usb 1-9: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 69.254929] usb 1-9: Product: USB2.0 Hub
[ 69.256630] hub 1-9:1.0: USB hub found
[ 69.256981] hub 1-9:1.0: 4 ports detected
[ 69.258124] usb: port power management may be unreliable
[ 69.389128] usb 1-11: new full-speed USB device number 5 using xhci_hcd
[ 69.538356] usb 1-11: New USB device found, idVendor=1462, idProduct=7d18,
bcdDevice= 0.01
[ 69.538385] usb 1-11: New USB device strings: Mfr=1, Product=2,
SerialNumber=3
[ 69.538400] usb 1-11: Product: MYSTIC LIGHT
[ 69.538410] usb 1-11: Manufacturer: MSI
[ 69.538420] usb 1-11: SerialNumber: A02021081805
[ 69.541808] input: MSI MYSTIC LIGHT as
/devices/pci0000:00/0000:00:14.0/usb1/1-11/1-11:1.0/0003:1462:7D18.0005/input/input9
[ 69.542258] hid-generic 0003:1462:7D18.0005: input,hiddev1,hidraw4: USB HID
v1.10 Device [MSI MYSTIC LIGHT ] on usb-0000:00:14.0-11/input0
[ 69.669124] usb 1-14: new full-speed USB device number 6 using xhci_hcd
[ 69.819394] usb 1-14: New USB device found, idVendor=8087, idProduct=0026,
bcdDevice= 0.02
[ 69.819423] usb 1-14: New USB device strings: Mfr=0, Product=0,
SerialNumber=0
[ 182.141933] sd 5:0:0:0: [sda] Synchronizing SCSI cache
[ 182.142749] sd 4:0:0:0: [sdb] Synchronizing SCSI cache
The last USB device in this list is a bluetooth card. I have blacklisted btusb,
but this didn't help, still hangs.
At 182 seconds I pressed CRTL_ALT_DEL and the times without sleep statements
come down to like 11 seconds when it hangs.
-----Original-Nachricht-----
Betreff: Re: AW: Debugging initramfs, server hangs during boot process
Datum: 2023-08-28T11:42:19+0200
Von: "Michel Verdier" <mv...@free.fr>
An: "debian-user@lists.debian.org" <debian-user@lists.debian.org>
On 2023-08-28, thah...@t-online.de wrote:
> It hangs in /usr/share/initramfs-tools/scripts/init-top/udev
>
> The 2nd last udev call hangs my box
> udevadm trigger --type=devices --action=add
Perhaps add before
udevadm trigger --verbose --dry-run --type=devices --action=add
