> On Sep 25, 2017, at 10:25 AM, Jimmy Johnson <field.engin...@gmail.com> wrote:
>
> On 09/23/2017 08:56 PM, Rick Thomas wrote:
>> I have two machines (out of a group of ten) that will not bring up their
>> ethernet interface at boot time if the interfaces is of type
>> �allow-hotplug�. When I change that to �auto� the interface comes up at
>> boot with no problem�
>> The remaining eight machines have no problem with allow-hotplug. (which is
>> the default as setup by the d-i)
>> It does not seem to correlate to kernel version. The two �auto� machines
>> are running 4.12 and 4.9; The �allow-hotplug� machines are running anything
>> between 3.16 and 4.12.
>> Nor does it seem to correlate with static vs dhcp. The two �auto� machines
>> are both using dhcp. The �allow-hotplug� machines are using a mixture of
>> static and dhcp.
>> Anybody have a clue as to what�s going on?
>> Thanks in advance�
>> Rick
>
> Hi, Rick
>
> As you have pointed out, things have changed, have you ran #ifconfig -a
> to get the name of your device? I'm thinking the name you are using is not
> the same name the system is using and why hotplug is not working?
OK:
root@macpro:~# ifconfig -a
enP1p3s15f0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 192.168.1.148 netmask 255.255.240.0 broadcast 192.168.15.255
inet6 fe80::211:24ff:fe38:1048 prefixlen 64 scopeid 0x20<link>
ether 00:11:24:38:10:48 txqueuelen 1000 (Ethernet)
RX packets 4450 bytes 4876801 (4.6 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 2649 bytes 246222 (240.4 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
So the interface name is “enP1p3s15f0"
I haven’t done anything to change the name from the original one assigned by
the installer.
Here’s what’s in /e/n/interfaces:
root@macpro:~# cat /etc/network/interfaces
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
source /etc/network/interfaces.d/*
# The loopback network interface
auto lo
iface lo inet loopback
# The primary network interface
auto enP1p3s15f0
iface enP1p3s15f0 net dhcp
I had to change “allow-hotplug” to “auto” to get it to come up on reboot:
root@macpro:~# diff /etc/network/interfaces.ORIG /etc/network/interfaces
11c11
< allow-hotplug enP1p3s15f0
---
> auto enP1p3s15f0
If there’s some place that’s mistakenly expecting a name like “eth0”, where
might it be located?
> --
> Jimmy Johnson
Rick
Linux user since 1987
