On Thu 18 Aug 2016 at 12:51:08 (+0200), Pascal Hambourg wrote:
> Le 18/08/2016 à 01:26, Henrique de Moraes Holschuh a écrit :
> >
> >Too bad it is WinXP, otherwise you'd have instant connectivity via IPv6
> >SLAAC.
>
> Windows XP supports IPv6. It is just disabled by default, so you
> need to enable it with something like "ipv6 enable". Even Windows
> 2000 could have experimental basic IPv6 support.
>
> SLAAC (stateless address autoconfiguration) requires a properly
> configured IPv6 router sending RA's (router advertisements). Debian
> running radvd can do this.
>
> Or do you mean link local addresses (fe80::/10) ? They're not the
> most convenient for everyday use.
The latter is certainly what I meant earlier. I find it very
convenient, just by using an alias and function (which I deliberately
avoid below). Here's the networking on my laptop as normally
configured wirelessly (with uname -a; /sbin/ifconfig -a;
ip route show; ip neigh show) and then when I connect to a
host with cat5 cable, and back again. (I edited out the lo
interface for brevity):
--
Laptop connected normally by wireless:
Linux west 3.16.0-4-686-pae #1 SMP Debian 3.16.7-ckt25-2+deb8u3 (2016-07-02)
i686 GNU/Linux
eth0 Link encap:Ethernet HWaddr 00:1c:23:3b:9f:34
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:18
wlan0 Link encap:Ethernet HWaddr 00:1c:bf:d5:28:76
inet addr:192.168.1.15 Bcast:192.168.1.255
Mask:255.255.255.0
inet6 addr: fe80::21c:bfff:fed5:2876/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:284407 errors:0 dropped:0 overruns:0 frame:0
TX packets:147975 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:430082452 (410.1 MiB) TX bytes:13065473 (12.4 MiB)
default via 192.168.1.1 dev wlan0
192.168.1.0/24 dev wlan0 proto kernel scope link src 192.168.1.15
192.168.1.19 dev wlan0 lladdr 00:13:72:83:0e:66 REACHABLE
192.168.1.1 dev wlan0 lladdr 44:94:fc:39:1f:ce REACHABLE
--
Remove 192.168.1.19's ethernet cable from wall and plug into laptop:
Linux west 3.16.0-4-686-pae #1 SMP Debian 3.16.7-ckt25-2+deb8u3 (2016-07-02)
i686 GNU/Linux
eth0 Link encap:Ethernet HWaddr 00:1c:23:3b:9f:34
inet6 addr: fe80::21c:23ff:fe3b:9f34/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:47 errors:0 dropped:0 overruns:0 frame:0
TX packets:48 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:10259 (10.0 KiB) TX bytes:10392 (10.1 KiB)
Interrupt:18
wlan0 Link encap:Ethernet HWaddr 00:1c:bf:d5:28:76
inet addr:192.168.1.15 Bcast:192.168.1.255
Mask:255.255.255.0
inet6 addr: fe80::21c:bfff:fed5:2876/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:322207 errors:0 dropped:0 overruns:0 frame:0
TX packets:166891 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:486912567 (464.3 MiB) TX bytes:14726418 (14.0 MiB)
default via 192.168.1.1 dev wlan0
192.168.1.0/24 dev wlan0 proto kernel scope link src 192.168.1.15
fe80::213:72ff:fe83:e66 dev eth0 lladdr 00:13:72:83:0e:66 REACHABLE
192.168.1.19 dev wlan0 lladdr 00:13:72:83:0e:66 STALE
192.168.1.1 dev wlan0 lladdr 44:94:fc:39:1f:ce REACHABLE
--
Log in to 192.168.1.19:
$ ssh -X fe80::213:72ff:fe83:e66%eth0
Linux alum 3.2.0-4-686-pae #1 SMP Debian 3.2.81-1 i686
[...]
You have new mail.
Last login: Thu Aug 18 10:08:12 2016 from west
$
--
Transfer file from 192.168.1.19 back to the laptop:
$ scp -p a_file david@[fe80::21c:23ff:fe3b:9f34%eth0]:/tmp/
a_file 100% 1280KB 1.3MB/s 00:01
$
--
Log out of 192.168.1.19:
$ [typed ^D]
Connection to fe80::213:72ff:fe83:e66%eth0 closed.
$
--
Transfer a file from laptop to 192.168.1.19:
$ scp -p a_file david@[fe80::213:72ff:fe83:e66%eth0]:/tmp/
a_file 100% 1280KB 1.3MB/s 00:01
$
--
Reconnect 192.168.1.19 to the wall socket:
Linux west 3.16.0-4-686-pae #1 SMP Debian 3.16.7-ckt25-2+deb8u3 (2016-07-02)
i686 GNU/Linux
eth0 Link encap:Ethernet HWaddr 00:1c:23:3b:9f:34
inet6 addr: fe80::21c:23ff:fe3b:9f34/64 Scope:Link
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:1385 errors:0 dropped:0 overruns:0 frame:0
TX packets:1495 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1457798 (1.3 MiB) TX bytes:1464872 (1.3 MiB)
Interrupt:18
wlan0 Link encap:Ethernet HWaddr 00:1c:bf:d5:28:76
inet addr:192.168.1.15 Bcast:192.168.1.255
Mask:255.255.255.0
inet6 addr: fe80::21c:bfff:fed5:2876/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:324108 errors:0 dropped:0 overruns:0 frame:0
TX packets:167844 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:489469428 (466.7 MiB) TX bytes:14814545 (14.1 MiB)
default via 192.168.1.1 dev wlan0
192.168.1.0/24 dev wlan0 proto kernel scope link src 192.168.1.15
fe80::213:72ff:fe83:e66 dev eth0 lladdr 00:13:72:83:0e:66 STALE
192.168.1.19 dev wlan0 lladdr 00:13:72:83:0e:66 REACHABLE
192.168.1.1 dev wlan0 lladdr 44:94:fc:39:1f:ce REACHABLE
--
Note that if you copy this method, you'll add lines to your
~/.ssh/known_hosts file.
Cheers,
David.
