have you tried accessing the device? the dmesg seems ok.... it looks like for some reason modprobe trys to load tuner.o twice...
Albert On Sun, 26 Oct 2003 11:03:46 -0500 stan <[EMAIL PROTECTED]> wrote: ... > And then I run into troubles :-( > > cogenvs:~# modprobe bttv > Using /lib/modules/2.4.22/kernel/drivers/media/video/tuner.o > insmod: a module named tuner already exists > /lib/modules/2.4.22/kernel/drivers/media/video/bttv.o: post-install > bttv failed/lib/modules/2.4.22/kernel/drivers/media/video/bttv.o: > insmod bttv failed cogenvs:~# exit > > Script done on Sun Oct 26 10:43:48 2003 > > dmesg after this: > > apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16) > i2c-core.o: i2c core module > i2c-algo-bit.o: i2c bit algorithm module > bttv: driver version 0.7.107 loaded > bttv: using 4 buffers with 2080k (8320k total) for capture > bttv: Host bridge is Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host > bridge bttv: Host bridge needs ETBF enabled. > bttv: Bt8xx card found (0). > PCI: Found IRQ 9 for device 00:0d.0 > PCI: Sharing IRQ 9 with 00:0d.1 > bttv0: Bt878 (rev 2) at 00:0d.0, irq: 9, latency: 64, mmio: 0xfeddf000 > bttv0: detected: Hauppauge WinTV [card=10], PCI subsystem ID is > 0070:13eb bttv0: using: BT878(Hauppauge (bt878)) > [card=10,autodetected] bttv0: enabling ETBF (430FX/VP3 compatibilty) > bttv0: Hauppauge/Voodoo msp34xx: reset line init [5] > i2c-core.o: adapter bt848 #0 registered as adapter 0. > bttv0: Hauppauge eeprom: model=61001, tuner=Philips FI1236 MK2 (2), > radio=no > bttv0: using tuner=2 > bttv0: i2c: checking for MSP34xx @ 0x80... not found > bttv0: i2c: checking for TDA9875 @ 0xb0... not found > bttv0: i2c: checking for TDA7432 @ 0x8a... not found > tvaudio: TV audio decoder + audio/video mux driver > tvaudio: known chips: > tda9840,tda9873h,tda9874h/a,tda9850,tda9855,tea6300,tea642 > 0,tda8425,pic16c54 (PV951),ta8874z > i2c-core.o: driver generic i2c audio driver registered. > i2c-core.o: driver i2c TV tuner driver registered. > tuner: chip found @ 0xc2 > tuner: type set to 2 (Philips NTSC (FI1236,FM1236 and compatibles)) > i2c-core.o: client [Philips NTSC (FI1236,FM1236 and] registered to > adapter[bt84 > 8 #0](pos. 0). > bttv0: PLL: 28636363 => 35468950 .. ok > bttv0: registered device video0 > bttv0: registered device vbi0 > > And an lsmod: > > Module Size Used by Not tainted > tuner 10888 1 (autoclean) > tvaudio 14408 0 (autoclean) (unused) > bttv 97376 0 (unused) > i2c-algo-bit 7560 1 [bttv] > i2c-core 13892 0 [tuner tvaudio bttv i2c-algo-bit] > apm 10600 0 (autoclean) > soundcore 4292 0 (autoclean) [bttv] > ide-scsi 10448 0 > agpgart 36608 0 (unused) > parport_pc 13732 1 (autoclean) > lp 6656 0 (autoclean) > parport 16096 1 (autoclean) [parport_pc lp] > keybdev 2116 0 (unused) > usbkbd 3676 0 (unused) > input 3744 0 [keybdev usbkbd] > usb-uhci 24592 0 (unused) > usbcore 65228 0 [usbkbd usb-uhci] > > What am I doing wrong? > > -- > "They that would give up essential liberty for temporary safety > deserve neither liberty nor safety." > -- Benjamin Franklin > > > -- > To UNSUBSCRIBE, email to [EMAIL PROTECTED] > with a subject of "unsubscribe". Trouble? Contact > [EMAIL PROTECTED] -- Albert Dengg <[EMAIL PROTECTED]> -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
