On 08/07/13 18:16, John McCardle wrote:
Thanks for the feedback, Glenn.
I adapted your block for a static IP for my network:
# The primary network interface
iface eth0 inet static
address 192.168.1.199
netmask 255.255.255.0
broadcast 192.168.1.255
network 192.168.1.0
gateway 192.168.1.1
This causes the system to take much longer to boot up, as it hangs at
the "Starting MTA" phase. Also, I'm no longer able to SSH into the
system via eth1, which is a USB ethernet adapter I use for
troubleshooting. On a semi-related note, upon attempting to plug a USB
keyboard into the system, the kernel crashes, which was not the case
when I was assembling the parts and installing the base OS. (These parts
are all brand new.)
To anyone googling this, save yourself the hassle: RMA whatever hardware
you have, and order something with a different brand of NIC on board.
Intel and Broadcom seem to be more sociable.
On Mon, Jul 8, 2013 at 2:05 AM, Glenn English <g...@slsware.com
<mailto:g...@slsware.com>> wrote:
On Jul 7, 2013, at 10:31 PM, John McCardle wrote:
> I am trying to use a realtek NIC under Linux (Debian 7.1). It is
the onboard ethernet in my Gigabyte 990FXA-UD3.
I'm sorry, I can't tell you how to make it go. But if it's any use,
I can tell you what a known working IPv4 1000baseT/Full looks like
on a Dell server I'm bringing up:
root@server:/etc/nsd3# lspci | egrep -i ethernet
04:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5722
Gigabit Ethernet PCI Express
root@server:/etc/nsd3# cat /etc/network/interfaces
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo eth0
iface lo inet loopback
allow-hotplug eth0
# The primary network interface
iface eth0 inet static
address 192.168.2.202
netmask 255.255.255.0
broadcast 192.168.2.255
network 192.168.2.0
gateway 192.168.2.1
# dns-* options are implemented by the resolvconf package,
if installed
root@server:/etc/nsd3# ifconfig eth0
eth0 Link encap:Ethernet HWaddr 00:26:b9:67:b6:ac
inet addr:192.168.2.202 Bcast:192.168.2.255
Mask:255.255.255.0
inet6 addr: fe80::226:b9ff:fe67:b6ac/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:7424 errors:0 dropped:0 overruns:0 frame:0
TX packets:7228 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:787352 (768.8 KiB) TX bytes:2108943 (2.0 MiB)
Interrupt:17
root@server:/etc/nsd3# ethtool eth0
Settings for eth0:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Supported pause frame use: No
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: Yes
Speed: 1000Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 1
Transceiver: internal
Auto-negotiation: on
MDI-X: Unknown
Supports Wake-on: g
Wake-on: d
Current message level: 0x000000ff (255)
drv probe link timer ifdown ifup
rx_err tx_err
Link detected: yes
root@server:/etc/nsd3# ethtool -i eth0
driver: tg3
version: 3.121
firmware-version: 5722-v3.10
bus-info: 0000:04:00.0
supports-statistics: yes
supports-test: yes
supports-eeprom-access: yes
supports-register-dump: yes
supports-priv-flags: no
What's that eth1 all about in your interfaces configuration? If eth0
is *the* onboard ethernet, might eth1 be confusing something?
--
Glenn English
One of my servers has an Intel miniITX motherboard DG41MJ, with the same
on-board ethernet hardware as yours:
$ lspci | grep -i ethernet
03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03)
$ sudo ethtool -i eth0
driver: r8169
version: 2.3LK-NAPI
firmware-version: rtl_nic/rtl8168d-1.fw
bus-info: 0000:03:00.0
supports-statistics: yes
supports-test: no
supports-eeprom-access: no
supports-register-dump: yes
supports-priv-flags: no
$ dmesg | grep -i r8169
r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
r8169 0000:03:00.0: setting latency timer to 64
r8169 0000:03:00.0: irq 43 for MSI/MSI-X
r8169 0000:03:00.0: eth0: RTL8168d/8111d at 0xffffc9000067a000,
00:27:0e:2b:3e:f1, XID 081000c0 IRQ 43
r8169 0000:03:00.0: eth0: jumbo features [frames: 9200 bytes, tx
checksumming: ko]
r8169 0000:03:00.0: firmware: agent loaded rtl_nic/rtl8168d-1.fw into memory
It's been working fine for two year or so, now running Wheezy. The one
difference to your 'ethtool' result I can see is that mine shows a
firmware version. Have you got the "firmware-realtek" package installed,
or is that not required for the Realtek 8168 driver?
--
Klaus
--
To UNSUBSCRIBE, email to debian-user-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
Archive: http://lists.debian.org/51db2400.1010...@gmail.com
