I am running a reasonably up-to-date Squeeze box (it has been a few days
since I did an aptitude update and safe-upgrade). This problem has
actually been occurring sporadically for a few weeks now. The system
will simply die. I leave the computer on 24/7, normally without
problems for weeks, or months, but lately that has not been working.
A few weeks back I had hard disk failure. After I replaced that disk
and reinstalled Squeeze (and /home and /usr/local from the old disk)
several problems started occurring. The dying system is the most
annoying. I will wake up, or come home from work and find the monitor
showing it's "No Signal" screen and the box is totally unresponsive. I
can not ssh in, or anything. The system is completely down. This
happenned every couple of days for a while and then it seemed to go
away. For at week, or more, I had no trouble. Then, yesterday evening
it died. After verifying that I could not ssh in, I rebooted. This
evening, I came home from work and spent a few minutes at the computer,
then had to go out at about 6:20PM. When I came back the system was
dead, again. I rebooted. This time I went through syslog and copied
out the parts just before the system died each of the last two times. I
generally try to avoid having to look at logs, but... I have inserted
those sections of log below. The only similarity that I can find is
that, in each case the last thing that shows in the log was running
cron.hourly. The only problem is that there is nothing in
/etc/cron.hourly/ (it is an empty directory). There are some entries
concerning the nouveau graphiocs driver. I know nothiong about drivers,
but I'm sure someone out there does. Is it pointing to a problem?
Anyway, here are the log snippets:
Jun 4 07:47:39 xander rsyslogd: [origin software="rsyslogd"
swVersion="4.6.4" x-pid="1246" x-info="http://www.rsyslog.com";] rsyslogd
was HUPed, type 'lightweight'.
Jun 4 07:47:44 xander anacron[23172]: Job `cron.daily' terminated
Jun 4 07:47:44 xander anacron[23172]: Normal exit (1 job run)
Jun 4 07:52:04 xander kernel: [755950.550970] [drm] nouveau
0000:01:00.0: Setting dpms mode 3 on vga encoder (output 0)
Jun 4 08:17:01 xander /USR/SBIN/CRON[23483]: (root) CMD ( cd / &&
run-parts --report /etc/cron.hourly)
Jun 4 08:31:09 xander kernel: [758296.121147] [drm] nouveau
0000:01:00.0: Setting dpms mode 0 on vga encoder (output 0)
Jun 4 09:09:23 xander kernel: [760590.284707] [drm] nouveau
0000:01:00.0: Setting dpms mode 3 on vga encoder (output 0)
Jun 4 09:17:01 xander /USR/SBIN/CRON[23688]: (root) CMD ( cd / &&
run-parts --report /etc/cron.hourly)
Jun 4 10:17:01 xander /USR/SBIN/CRON[23854]: (root) CMD ( cd / &&
run-parts --report /etc/cron.hourly)
Jun 4 10:29:26 xander dhclient: DHCPREQUEST on eth0 to 192.168.1.1 port 67
Jun 4 10:29:26 xander dhclient: DHCPACK from 192.168.1.1
Jun 4 10:29:26 xander dhclient: bound to 192.168.1.2 -- renewal in
42208 seconds.
Jun 4 11:17:01 xander /USR/SBIN/CRON[24009]: (root) CMD ( cd / &&
run-parts --report /etc/cron.hourly)
Jun 4 12:17:01 xander /USR/SBIN/CRON[24169]: (root) CMD ( cd / &&
run-parts --report /etc/cron.hourly)
Jun 4 13:17:01 xander /USR/SBIN/CRON[24300]: (root) CMD ( cd / &&
run-parts --report /etc/cron.hourly)
Jun 4 18:30:00 xander kernel: imklog 4.6.4, log source = /proc/kmsg
started.
Jun 4 18:30:00 xander rsyslogd: [origin software="rsyslogd"
swVersion="4.6.4" x-pid="1276" x-info="http://www.rsyslog.com";] (re)start
and
Jun 5 08:04:41 xander rsyslogd: [origin software="rsyslogd"
swVersion="4.6.4" x-pid="1276" x-info="http://www.rsyslog.com";] rsyslogd
was HUPed, type 'lightweight'.
Jun 5 08:04:41 xander rsyslogd: [origin software="rsyslogd"
swVersion="4.6.4" x-pid="1276" x-info="http://www.rsyslog.com";] rsyslogd
was HUPed, type 'lightweight'.
Jun 5 08:05:08 xander anacron[6109]: Job `cron.daily' terminated
Jun 5 08:05:08 xander anacron[6109]: Normal exit (1 job run)
Jun 5 08:17:01 xander /USR/SBIN/CRON[6504]: (root) CMD ( cd / &&
run-parts --report /etc/cron.hourly)
Jun 5 08:31:48 xander kernel: [50534.578689] [drm] nouveau
0000:01:00.0: Setting dpms mode 3 on vga encoder (output 0)
Jun 5 09:17:01 xander /USR/SBIN/CRON[6716]: (root) CMD ( cd / &&
run-parts --report /etc/cron.hourly)
Jun 5 10:17:01 xander /USR/SBIN/CRON[6929]: (root) CMD ( cd / &&
run-parts --report /etc/cron.hourly)
Jun 5 11:17:01 xander /USR/SBIN/CRON[7114]: (root) CMD ( cd / &&
run-parts --report /etc/cron.hourly)
Jun 5 12:17:01 xander /USR/SBIN/CRON[7287]: (root) CMD ( cd / &&
run-parts --report /etc/cron.hourly)
Jun 5 13:17:01 xander /USR/SBIN/CRON[7458]: (root) CMD ( cd / &&
run-parts --report /etc/cron.hourly)
Jun 5 14:17:01 xander /USR/SBIN/CRON[7508]: (root) CMD ( cd / &&
run-parts --report /etc/cron.hourly)
Jun 5 15:17:01 xander /USR/SBIN/CRON[7557]: (root) CMD ( cd / &&
run-parts --report /etc/cron.hourly)
Jun 5 16:12:35 xander dhclient: DHCPREQUEST on eth0 to 192.168.1.1 port 67
Jun 5 16:12:35 xander dhclient: DHCPACK from 192.168.1.1
Jun 5 16:12:35 xander dhclient: bound to 192.168.1.2 -- renewal in
34670 seconds.
Jun 5 16:17:01 xander /USR/SBIN/CRON[7608]: (root) CMD ( cd / &&
run-parts --report /etc/cron.hourly)
Jun 5 16:31:21 xander kernel: [79307.749897] [drm] nouveau
0000:01:00.0: Setting dpms mode 0 on vga encoder (output 0)
Jun 5 17:17:01 xander /USR/SBIN/CRON[7663]: (root) CMD ( cd / &&
run-parts --report /etc/cron.hourly)
Jun 5 18:11:30 xander kernel: [85317.130389] [drm] nouveau
0000:01:00.0: Setting dpms mode 3 on vga encoder (output 0)
Jun 5 18:11:30 xander kernel: [85317.150673] [drm] nouveau
0000:01:00.0: Setting dpms mode 0 on vga encoder (output 0)
Jun 5 18:11:30 xander kernel: [85317.150685] [drm] nouveau
0000:01:00.0: Output VGA-1 is running on CRTC 0 using output A
Jun 5 18:11:30 xander kernel: [85317.324416] [drm] nouveau
0000:01:00.0: Load detected on output A
Jun 5 18:11:31 xander kernel: [85317.551962] [drm] nouveau
0000:01:00.0: Setting dpms mode 3 on vga encoder (output 0)
Jun 5 18:11:31 xander kernel: [85317.572244] [drm] nouveau
0000:01:00.0: Setting dpms mode 0 on vga encoder (output 0)
Jun 5 18:11:31 xander kernel: [85317.572251] [drm] nouveau
0000:01:00.0: Output VGA-1 is running on CRTC 0 using output A
Jun 5 18:17:01 xander /USR/SBIN/CRON[7767]: (root) CMD ( cd / &&
run-parts --report /etc/cron.hourly)
Jun 5 18:54:21 xander kernel: [87887.751760] [drm] nouveau
0000:01:00.0: Setting dpms mode 3 on vga encoder (output 0)
Jun 5 19:17:01 xander /USR/SBIN/CRON[7873]: (root) CMD ( cd / &&
run-parts --report /etc/cron.hourly)
Jun 5 21:08:47 xander kernel: imklog 4.6.4, log source = /proc/kmsg
started.
Jun 5 21:08:47 xander rsyslogd: [origin software="rsyslogd"
swVersion="4.6.4" x-pid="1259" x-info="http://www.rsyslog.com";] (re)start
If there is anything here that points to a problem, please let me know.
If there is any other data that would help diagnose this, I will do my
best to provide it.
Thank you for any help.
Marc
--
To UNSUBSCRIBE, email to debian-user-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
Archive: http://lists.debian.org/4fcee739.1040...@gmail.com
