On Mon, 08 Aug 2011 14:54:26 -0400, Wayne Topa wrote: > On 08/08/2011 02:02 PM, Wayne Topa wrote:
(...) >>> I will re-do the question... Do you think the above error has >>> something to do with udev/kernel not detecting the printer? >>> >> It is not detecting the usb to parallel interface, yes. But it is listed and visible when you run "lsusb" :-? >>> "mtp-probe" sounds to me like another thing (used on/for USB media >>> players): >> >> That error was from wheezy when i plugged in the usb printer cable. >> >> Here is what I see in Squeeze when I plug in that cable: >> Aug 8 13:52:38 dj kernel: [14830.023088] usb 3-1: New USB device strings: >> Mfr=1, Product=2, SerialNumber=0 >> Aug 8 13:52:38 dj kernel: [14830.023092] usb 3-1: Product: IEEE-1284 >> Controller >> Aug 8 13:52:38 dj kernel: [14830.023095] usb 3-1: Manufacturer: Prolific >> Technology Inc. >> Aug 8 13:52:38 dj kernel: [14830.034204] usblp1: USB Bidirectional printer >> dev 3 if 0 alt 1 proto 2 vid 0x067B pid 0x2305 Looks good... (...) >>> What's the full (I mean, the relevant part for USB stack) dmesg output >>> when you connect the printer? What about "lsusb"? Do other USB devices >>> work? > > following is from wheezy > Pulled Printer cable then reinserted > > Aug 8 14:08:47 dj kernel: [ 317.212264] usb 3-1: USB disconnect, device > number 2 > Aug 8 14:08:47 dj kernel: [ 317.212532] usblp1: removed > Aug 8 14:08:52 dj anacron[2389]: Job `cron.daily' started > Aug 8 14:08:54 dj kernel: [ 324.940051] usb 3-1: new full speed USB device > number 3 using ohci_hcd > Aug 8 14:08:55 dj kernel: [ 325.107129] usb 3-1: New USB device found, > idVendor=067b, idProduct=2305 > Aug 8 14:08:55 dj kernel: [ 325.107138] usb 3-1: New USB device strings: > Mfr=1, Product=2, SerialNumber=0 > Aug 8 14:08:55 dj kernel: [ 325.107145] usb 3-1: Product: IEEE-1284 > Controller > Aug 8 14:08:55 dj kernel: [ 325.107150] usb 3-1: Manufacturer: Prolific > Technology Inc. > Aug 8 14:08:55 dj kernel: [ 325.118268] usblp1: USB Bidirectional printer > dev 3 if 0 alt 1 proto 2 vid 0x067B pid 0x2305 Device seems to be there (usblp1). How about "ls -l /dev/usblp1"? > Aug 8 14:08:55 dj mtp-probe: checking bus 3, device 3: > "/sys/devices/pci0000:00/0000:00:12.0/usb3/3-1" > Aug 8 14:08:55 dj mtp-probe: bus: 3, device: 3 was not an MTP device And this looks like an informative message, I mean, like if it were telling you "hey, I have detected an USB device but is not suitable to setting it as an MTP". Have you tried to set the printer from CUPS web interface? Greetings, -- Camaleón -- To UNSUBSCRIBE, email to debian-user-requ...@lists.debian.org with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org Archive: http://lists.debian.org/pan.2011.08.09.14.54...@gmail.com
