Hi, What kind of CD-RW media is that? Is it a High-Speed media? Because if not, you can only write them up to 4x speed
Martin On Thu, 2003-09-25 at 14:35, Dan Bowtell wrote: > I've just installed an ASUS CRW-5224A CD writer in my debian computer > and I've got it running under scsi emulation. I've just attempted to > burn a CD at the moment but it took 15 minutes to get about 10% through > and then aborted. The log for it is below. The writer works fine running > under windows, I burned the debian installation cds using it. > > Thanks in advance, > Dan > > Calling: /usr/lib/xcdroast/bin/xcdrwrap CDRECORD dev= "0,0,0" > gracetime=2 fs=5120k driveropts=burnfree -v -useinfo speed=24 -dao > -eject -pad -data "/home/vrih/track-01.img" ... > > scsidev: '0,0,0' > scsibus: 0 target: 0 lun: 0 > Linux sg driver version: 3.1.25 > SCSI buffer size: 64512 > Cdrecord-Clone 2.01a18 (i686-pc-linux-gnu) Copyright (C) 1995-2003 Jörg > Schilling > TOC Type: 1 = CD-ROM > Using libscg version 'schily-0.7' > Driveropts: 'burnfree' > atapi: 1 > Device type : Removable CD-ROM > Version : 0 > Response Format: 1 > Vendor_info : 'ASUS ' > Identifikation : 'CRW-5224A ' > Revision : '1.35' > Device seems to be: Generic mmc CD-RW. > Current: 0x000A > Profile: 0x000A (current) > Profile: 0x0009 > Profile: 0x0008 > Profile: 0x0002 (current) > Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr). > Driver flags : MMC-3 SWABAUDIO BURNFREE > Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P > RAW/R96R > Drive buf size : 1951488 = 1905 KB > FIFO size : 5242880 = 5120 KB > cdrecord.mmap: Operation not permitted. WARNING: Cannot set RR-scheduler > cdrecord.mmap: Permission denied. WARNING: Cannot set priority using > setpriority(). > cdrecord.mmap: WARNING: This causes a high risk for buffer underruns. > pregap1: -1 > Track 01: data 161 MB padsize: 30 KB > Total size: 185 MB (18:19.96) = 82497 sectors > Lout start: 185 MB (18:21/72) = 82497 sectors > Current Secsize: 2048 > ATIP info from disk: > Indicated writing power: 1 > Reference speed: 0 > Is not unrestricted > Is erasable > Disk sub type: Ultra High speed Rewritable media (2) > ATIP start of lead in: -11076 (97:34/24) > ATIP start of lead out: 336075 (74:43/00) > 1T speed low: 16 1T speed high: 16 > 2T speed low: 8 2T speed high: 24 > power mult factor: 4 5 > recommended erase/write power: 1 > A1 values: 66 4A 99 > A2 values: 38 80 00 > A3 values: 04 C4 A0 > Disk type: Phase change > Manuf. index: 11 > Manufacturer: Mitsubishi Chemical Corporation > Blocks total: 336075 Blocks current: 336075 Blocks remaining: 253578 > Starting to write CD/DVD at speed 24 in real SAO mode for single > session. > Waiting for reader process to fill input buffer ... > input buffer ready. > BURN-Free is ON. > Performing OPC... > Sending CUE sheet... > cdrecord.mmap: WARNING: Drive returns wrong startsec (0) using -150 > Writing pregap for track 1 at -150 > Starting new track at sector: 0 > cdrecord.mmap: Input/output error. write_g1: scsi sendcmd: retryable > error > CDB: 2A 00 00 00 1C 18 00 00 1F 00 > status: 0x0 (GOOD STATUS) > cmd finished after 200.619s timeout 200s > cdrecord.mmap: A write error occured. > cdrecord.mmap: Please properly read the error message above. > > cdrecord.mmap: Input/output error. test unit ready: scsi sendcmd: no > error > write track data: error after 14729216 bytes > CDB: 00 00 00 00 00 00 > Writing time: 1040.990s > status: 0x2 (CHECK CONDITION) > Average write speed 1.1x. > Sense Bytes: 70 00 06 00 00 00 00 0A 00 00 00 00 29 00 00 00 > Min drive buffer fill was 0% > Sense Key: 0x6 Unit Attention, Segment 0 > Total of 3 possible drive buffer underruns predicted. > Sense Code: 0x29 Qual 0x00 (power on, reset, or bus device reset > occurred) Fru 0x0 > Fixating... > Sense flags: Blk 0 (not valid) > Fixating time: 0.001s > cmd finished after 0.340s timeout 200s > BURN-Free was 8 times used. > cdrecord.mmap: fifo had 312 puts and 233 gets. > cdrecord.mmap: fifo was 0 times empty and 61 times full, min fill was > 92%. > -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
