Jack, With your pastebin information and the mdstat information (that last information in your mail and pastebins was critical good stuff) and I found this old posting from you too: :-)
http://lists.debian.org/debian-user/2009/10/msg00808.html With all of that I deduce the following: /dev/md125 /dev/sda1 /dev/sdc1 (10G) root partition with no lvm /dev/md126 /dev/sda5 /dev/sdc5 (288G) LVM for /home, /var, swap, ... /dev/md127 /dev/sdb /dev/sdd (465G) as yet unformatted Jack, If that is wrong please correct me. But I think that is right. The mdstat data showed that the arrays are sync'd. The UUIDs are as follows. ARRAY /dev/md/125_0 metadata=0.90 UUID=e45b34d8:50614884:1f1d6a6a:d9c6914c ARRAY /dev/md/126_0 metadata=0.90 UUID=c06c0ea6:5780b170:ea2fd86a:09558bd1 ARRAY /dev/md/Speeduke:2 metadata=1.2 name=Speeduke:2 UUID=91ae6046:969bad93:92136016:116577fd The desired state: /dev/md0 /dev/sda1 /dev/sdc1 (10G) root partition with no lvm /dev/md1 /dev/sda5 /dev/sdc5 (288G) LVM for /home, /var, swap, ... Will get to /dev/md2 later... > My thinking is that I should rerun mdadm and reassemble the arrays to > the original definitions... /md0 from sda1 & sdc1 > /md1 from sda5 & sdc5 note: sda2 &sdc2 > are legacy msdos extended partitions. > I would not build a md device with msdos extended partitions under LVM2 > at this time.. Agree? Agreed. You want to rename the arrays. Don't touch the msdos partitions. > Is the above doable? If I can figure the right mdadm commands...8-) Yes. It is doable. You can rename the array. First stop the array. Then assemble it again with the new desired name. Here is what you want to do. Tom, Henrique, others, Please double check me on these. mdadm --stop /dev/md125 mdadm --assemble /dev/md0 --update=super-minor /dev/sda1 /dev/sdc1 mdadm --stop /dev/126 mdadm --assemble /dev/md1 --update=super-minor /dev/sda5 /dev/sdc5 That should by itself be enough to get the arrays going. But, and this is an important but, did you previously add the new disk array to the LVM volume group on the above array? If so then you are not done yet. The LVM volume group won't be able to assemble without the new disk. If you did then you need to fix up LVM next. I think you should try to get back to where you were before when your system was working. Therefore I would remove the new disks from the LVM volume group. But I don't know if you did or did not add it yet. So I must stop here and wait for further information from you. I don't know if your rescue disk has lvm automatically configured or not. You may need to load the device mapper module dm_mod. I don't know. If you do then here is a hint: modprobe dm_mod To scan for volume groups: vgscan To activate a volume group: vgchange -ay To display the physical volumes associated with a volume group: pvdisplay If the new disks haven't been added to the volume group (I am hoping not) then you should be home free. But if they are then I think you will need to remove them first. I don't know if the LVM actions above are going to be needed. I am just trying to proactively give some possible hints. Bob
signature.asc
Description: Digital signature
