Hi there, new to the list.
I'm trying to run squeeze/amd64/gnome on a compaq 6820S .
Video card is a mobile radeon 1350 :
01:00.0 VGA compatible controller: ATI Technologies Inc RV516 [Mobility Radeon
X1350]
Driver in use in "radeon", and it seems is using kms
r...@nb-pablo:/home/pablo# lsmod | grep radeon
radeon 573612 2
ttm 40002 1 radeon
drm_kms_helper 20065 1 radeon
drm 142375 4 radeon,ttm,drm_kms_helper
i2c_algo_bit 4225 1 radeon
i2c_core 15712 4 radeon,drm_kms_helper,drm,i2c_algo_bit
The thing takes ages (like 5 minutes) to load and all around dmesg are :
[ 156.031447] [drm:edid_is_valid] *ERROR* Raw EDID:
[ 156.031450] <3>00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
................
[ 156.031452] <3>00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
................
[ 156.031454] <3>00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
................
[ 156.031455] <3>00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
................
[ 156.031457] <3>00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
................
[ 156.031459] <3>00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
................
[ 156.031461] <3>00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
................
[ 156.031463] <3>00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
................
[ 156.031465]
[ 156.031467] radeon 0000:01:00.0: DVI-I-1: EDID invalid.
[ 156.031478] [drm:radeon_dvi_detect] *ERROR* DVI-I-1: probed a monitor but
no|invalid EDID
The monitor is :
r...@nb-pablo:/home/pablo# get-edid | parse-edid
parse-edid: parse-edid version 2.0.0
get-edid: get-edid version 2.0.0
Performing real mode VBE call
Interrupt 0x10 ax=0x4f00 bx=0x0 cx=0x0
Function supported
Call successful
VBE version 300
VBE string at 0xc0254 "ATI ATOMBIOS"
VBE/DDC service about to be called
Report DDC capabilities
Performing real mode VBE call
Interrupt 0x10 ax=0x4f15 bx=0x0 cx=0x0
Function supported
Call successful
Monitor and video card combination does not support DDC1 transfers
Monitor and video card combination supports DDC2 transfers
0 seconds per 128 byte EDID block transfer
Screen is not blanked during DDC transfer
Reading next EDID block
VBE/DDC service about to be called
Read EDID
Performing real mode VBE call
Interrupt 0x10 ax=0x4f15 bx=0x1 cx=0x0
Function supported
Call successful
parse-edid: EDID checksum passed.
# EDID version 1 revision 3
Section "Monitor"
# Block type: 2:0 3:f
# Block type: 2:0 3:fe
# Block type: 2:0 3:fe
Identifier "SEC:4738"
VendorName "SEC"
ModelName "SEC:4738"
# Block type: 2:0 3:f
# Block type: 2:0 3:fe
# Block type: 2:0 3:fe
# DPMS capabilities: Active off:no Suspend:no Standby:no
Mode "1440x900" # vfreq 60.002Hz, hfreq 54.722kHz
DotClock 96.310000
HTimings 1440 1504 1536 1760
VTimings 900 903 906 912
Flags "-HSync" "-VSync"
EndMode
# Block type: 2:0 3:f
# Block type: 2:0 3:fe
# Block type: 2:0 3:fe
EndSection
which correctly states it has a resolution of 1440x900 .
It worked fine with lenny/amd64 on the same machine, also con ubuntu 9.10/amd64
.
I tried using xserver-xorg-video-radeonhd and works almost fine (no monitor
detected but
behaves properly) , but no 3d accel .
So, i'd like to get it working with xserver-xorg-video-radeon , nicely.
That is, i'm requesting some help ...
Regards.
Pablo Sánchez.
--
To UNSUBSCRIBE, email to debian-user-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
Archive: http://lists.debian.org/4ce6f9d3.7090...@adinet.com.uy
