This may point you in the right direction: http://forums13.itrc.hp.com/service/forums/questionanswer.do?admit=109447627+1263982812391+28353475&threadId=760337
Looks like you might need to update the card's firmware, try it in another PCI-X slot, or remove all the other PCI/X cards to see if there is a conflict. I don't have any direct experience with FC cards and Linux, only VMware ESX. I have seen situations where drivers fail when the card is not attached to a switch. Way back in the day I've seen SCSI drivers fail during boot if there were no drives attached. Goofy stuff. I'm betting you're in a similar goofy situation. That card and driver combo appear to be finicky. -- Stan Marco Vaschetto put forth on 1/20/2010 2:36 AM: > Stan Hoeppner ha scritto: >> Can we get some relevant dmesg and /var/log/boot output? Also, are >> you loading >> libfc? You'll need it in addition to lpfc. >> >> Have you tried building a custom kernel with all the stuff built in, >> not as modules? >> >> > No, in fact I didn't try whit a compiled kernel but only precompiled > kernel, > > the version I have try is 2.6.26-2-686 and 2.6.32-trunk-686, but steal > now is not work > > now I will give you the output of a "clean" based system of Debian > Lenny kernel 2.6.26-2-686 and to day I will try your suggestion > > of use a recompiled kernel; and no, is without the libfc. I will try to > fix that. > > so this is the output on the bootstrap: > > the file log of boot is empty > > LSAXYZAEYY:~# cat /var/log/boot (Nothing has been logged yet.) > > this is the output of dmesg (complete)of a new installation: > > LSAXYZAEYY:/# dmesg > [ 0.000000] Initializing cgroup subsys cpuset > [ 0.000000] Initializing cgroup subsys cpu > [ 0.000000] Linux version 2.6.26-2-686 (Debian 2.6.26-19lenny2) > (da...@debian.org) (gcc version 4.1.3 20080704 (prerelease) (Debian > 4.1.2-25)) #1 SMP Wed Nov 4 20:45:37 UTC 2009 > [ 0.000000] BIOS-provided physical RAM map: > [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f400 (usable) > [ 0.000000] BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved) > [ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) > [ 0.000000] BIOS-e820: 0000000000100000 - 000000008fffa000 (usable) > [ 0.000000] BIOS-e820: 000000008fffa000 - 0000000090000000 (ACPI data) > [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) > [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved) > [ 0.000000] BIOS-e820: 00000000ffc00000 - 0000000100000000 (reserved) > [ 0.000000] 1407MB HIGHMEM available. > [ 0.000000] 896MB LOWMEM available. > [ 0.000000] found SMP MP-table at [c00f4fd0] 000f4fd0 > [ 0.000000] Entering add_active_range(0, 0, 589818) 0 entries of 256 > used > [ 0.000000] Zone PFN ranges: > [ 0.000000] DMA 0 -> 4096 > [ 0.000000] Normal 4096 -> 229376 > [ 0.000000] HighMem 229376 -> 589818 > [ 0.000000] Movable zone start PFN for each node > [ 0.000000] early_node_map[1] active PFN ranges > [ 0.000000] 0: 0 -> 589818 > [ 0.000000] On node 0 totalpages: 589818 > [ 0.000000] DMA zone: 32 pages used for memmap > [ 0.000000] DMA zone: 0 pages reserved > [ 0.000000] DMA zone: 4064 pages, LIFO batch:0 > [ 0.000000] Normal zone: 1760 pages used for memmap > [ 0.000000] Normal zone: 223520 pages, LIFO batch:31 > [ 0.000000] HighMem zone: 2816 pages used for memmap > [ 0.000000] HighMem zone: 357626 pages, LIFO batch:31 > [ 0.000000] Movable zone: 0 pages used for memmap > [ 0.000000] DMI 2.3 present. > [ 0.000000] ACPI: RSDP 000F4F70, 0014 (r0 COMPAQ) > [ 0.000000] ACPI: RSDT 8FFFA000, 0030 (r1 COMPAQ D15 > 2 Ò 162E) > [ 0.000000] ACPI: FACP 8FFFA040, 0074 (r1 COMPAQ D15 > 2 Ò 162E) > [ 0.000000] ACPI: DSDT 8FFFA240, 22F1 (r1 COMPAQ DSDT 1 > MSFT 100000B) > [ 0.000000] ACPI: FACS 8FFFA0C0, 0040 > [ 0.000000] ACPI: APIC 8FFFA100, 00AC (r1 COMPAQ 00000083 > 2 Ò 162E) > [ 0.000000] ACPI: SPCR 8FFFA1C0, 0050 (r1 COMPAQ SPCRRBSU > 1 Ò 162E) > [ 0.000000] ACPI: PM-Timer IO Port: 0x920 > [ 0.000000] ACPI: Local APIC address 0xfee00000 > [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) > [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled) > [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x04] disabled) > [ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x06] disabled) > [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) > [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled) > [ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x05] disabled) > [ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x07] disabled) > [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1]) > [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) > [ 0.000000] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI > 0-15 > [ 0.000000] ACPI: IOAPIC (id[0x03] address[0xfec01000] gsi_base[16]) > [ 0.000000] IOAPIC[1]: apic_id 3, version 17, address 0xfec01000, GSI > 16-31 > [ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec02000] gsi_base[32]) > [ 0.000000] IOAPIC[2]: apic_id 4, version 17, address 0xfec02000, GSI > 32-47 > [ 0.000000] ACPI: IOAPIC (id[0x05] address[0xfec03000] gsi_base[48]) > [ 0.000000] IOAPIC[3]: apic_id 5, version 17, address 0xfec03000, GSI > 48-63 > [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge) > [ 0.000000] ACPI: IRQ0 used by override. > [ 0.000000] ACPI: IRQ2 used by override. > [ 0.000000] ACPI: IRQ9 used by override. > [ 0.000000] Enabling APIC mode: Flat. Using 4 I/O APICs > [ 0.000000] Using ACPI (MADT) for SMP configuration information > [ 0.000000] Allocating PCI resources starting at 98000000 (gap: > 90000000:6ec00000) > [ 0.000000] PM: Registered nosave memory: 000000000009f000 - > 00000000000a0000 > [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - > 00000000000f0000 > [ 0.000000] PM: Registered nosave memory: 00000000000f0000 - > 0000000000100000 > [ 0.000000] SMP: Allowing 8 CPUs, 6 hotplug CPUs > [ 0.000000] PERCPU: Allocating 37992 bytes of per cpu data > [ 0.000000] NR_CPUS: 8, nr_cpu_ids: 8 > [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. > Total pages: 585210 > [ 0.000000] Kernel command line: > BOOT_IMAGE=/boot/vmlinuz-2.6.26-2-686 root=/dev/cciss/c0d0p1 ro > [ 0.000000] mapped APIC to ffffb000 (fee00000) > [ 0.000000] mapped IOAPIC to ffffa000 (fec00000) > [ 0.000000] mapped IOAPIC to ffff9000 (fec01000) > [ 0.000000] mapped IOAPIC to ffff8000 (fec02000) > [ 0.000000] mapped IOAPIC to ffff7000 (fec03000) > [ 0.000000] Enabling fast FPU save and restore... done. > [ 0.000000] Enabling unmasked SIMD FPU exception support... done. > [ 0.000000] Initializing CPU#0 > [ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes) > [ 0.000000] Detected 3065.986 MHz processor. > [ 0.004000] Console: colour VGA+ 80x25 > [ 0.004000] console [tty0] enabled > [ 0.004000] Dentry cache hash table entries: 131072 (order: 7, 524288 > bytes) > [ 0.004000] Inode-cache hash table entries: 65536 (order: 6, 262144 > bytes) > [ 0.004000] Memory: 2333484k/2359272k available (1770k kernel code, > 24676k reserved, 750k data, 244k init, 1441768k highmem) > [ 0.004000] virtual kernel memory layout: > [ 0.004000] fixmap : 0xfff4c000 - 0xfffff000 ( 716 kB) > [ 0.004000] pkmap : 0xff800000 - 0xffc00000 (4096 kB) > [ 0.004000] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) > [ 0.004000] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) > [ 0.004000] .init : 0xc037f000 - 0xc03bc000 ( 244 kB) > [ 0.004000] .data : 0xc02baaa1 - 0xc0376620 ( 750 kB) > [ 0.004000] .text : 0xc0100000 - 0xc02baaa1 (1770 kB) > [ 0.004000] Checking if this processor honours the WP bit even in > supervisor mode...Ok. > [ 0.004000] CPA: page pool initialized 1 of 1 pages preallocated > [ 0.084008] Calibrating delay using timer specific routine.. 6137.22 > BogoMIPS (lpj=12274457) > [ 0.084159] Security Framework initialized > [ 0.084223] SELinux: Disabled at boot. > [ 0.084280] Capability LSM initialized > [ 0.084353] Mount-cache hash table entries: 512 > [ 0.084640] Initializing cgroup subsys ns > [ 0.084699] Initializing cgroup subsys cpuacct > [ 0.084754] Initializing cgroup subsys devices > [ 0.084833] CPU: Trace cache: 12K uops, L1 D cache: 8K > [ 0.084923] CPU: L2 cache: 512K > [ 0.084976] CPU: Physical Processor ID: 0 > [ 0.085033] Intel machine check architecture supported. > [ 0.085091] Intel machine check reporting enabled on CPU#0. > [ 0.085146] CPU0: Intel P4/Xeon Extended MCE MSRs (12) available > [ 0.085205] CPU0: Thermal monitoring enabled > [ 0.085276] Checking 'hlt' instruction... OK. > [ 0.101415] ACPI: Core revision 20080321 > [ 0.112007] ENABLING IO-APIC IRQs > [ 0.112007] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 > [ 0.151663] CPU0: Intel(R) Xeon(TM) CPU 3.06GHz stepping 09 > [ 0.152009] Booting processor 1/1 ip 6000 > [ 0.160010] Initializing CPU#1 > [ 0.160010] Calibrating delay using timer specific routine.. 6131.91 > BogoMIPS (lpj=12263831) > [ 0.160010] CPU: Trace cache: 12K uops, L1 D cache: 8K > [ 0.160010] CPU: L2 cache: 512K > [ 0.160010] CPU: Physical Processor ID: 0 > [ 0.160010] Intel machine check architecture supported. > [ 0.160010] Intel machine check reporting enabled on CPU#1. > [ 0.160010] CPU1: Intel P4/Xeon Extended MCE MSRs (12) available > [ 0.160010] CPU1: Thermal monitoring enabled > [ 0.239895] CPU1: Intel(R) Xeon(TM) CPU 3.06GHz stepping 09 > [ 0.240015] checking TSC synchronization [CPU#0 -> CPU#1]: passed. > [ 0.244015] Brought up 2 CPUs > [ 0.244015] Total of 2 processors activated (12269.14 BogoMIPS). > [ 0.244015] CPU0 attaching sched-domain: > [ 0.244015] domain 0: span 0-1 > [ 0.244015] groups: 0 1 > [ 0.244015] domain 1: span 0-1 > [ 0.244015] groups: 0-1 > [ 0.244015] CPU1 attaching sched-domain: > [ 0.244015] domain 0: span 0-1 > [ 0.244015] groups: 1 0 > [ 0.244015] domain 1: span 0-1 > [ 0.244015] groups: 0-1 > [ 0.244015] net_namespace: 660 bytes > [ 0.244015] Booting paravirtualized kernel on bare hardware > [ 0.244015] NET: Registered protocol family 16 > [ 0.244015] ACPI: bus type pci registered > [ 0.256016] PCI: PCI BIOS revision 2.10 entry at 0xf0094, last bus=2 > [ 0.256016] PCI: Using configuration type 1 for base access > [ 0.256016] Setting up standard PCI resources > [ 0.264016] ACPI: EC: Look up EC in DSDT > [ 0.267115] ACPI: Interpreter enabled > [ 0.267175] ACPI: (supports S0 S4 S5) > [ 0.267343] ACPI: Using IOAPIC for interrupt routing > [ 0.272017] ACPI: PCI Root Bridge [PCI0] (0000:00) > [ 0.272017] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] > [ 0.276017] ACPI: PCI Interrupt Link [IUSB] (IRQs 4 5 7 10 11 15) *3 > [ 0.276017] ACPI: PCI Interrupt Link [RAID] (IRQs 11) *0, disabled. > [ 0.276017] ACPI: PCI Interrupt Link [IN18] (IRQs 4 5 7 10 *11 15) > [ 0.276017] ACPI: PCI Interrupt Link [IN19] (IRQs *4 5 7 10 11 15) > [ 0.276017] ACPI: PCI Interrupt Link [IN21] (IRQs 4 *5 7 10 11 15) > [ 0.276017] ACPI: PCI Interrupt Link [IN22] (IRQs 4 5 7 10 11 15) *0, > disabled. > [ 0.276017] ACPI: PCI Interrupt Link [IN23] (IRQs 4 5 7 10 *11 15) > [ 0.276487] ACPI: PCI Interrupt Link [IN24] (IRQs 4 5 *7 10 11 15) > [ 0.276951] ACPI: PCI Interrupt Link [IN25] (IRQs 4 5 7 *10 11 15) > [ 0.277419] ACPI: PCI Interrupt Link [IN26] (IRQs 4 5 7 10 *11 15) > [ 0.280017] ACPI: PCI Interrupt Link [IN27] (IRQs 4 5 7 *10 11 15) > [ 0.280481] ACPI: PCI Interrupt Link [IN28] (IRQs 4 5 7 10 11 15) *0, > disabled. > [ 0.282147] Linux Plug and Play Support v0.97 (c) Adam Belay > [ 0.282147] pnp: PnP ACPI init > [ 0.282147] ACPI: bus type pnp registered > [ 0.286148] pnp: PnP ACPI: found 10 devices > [ 0.286148] ACPI: ACPI bus type pnp unregistered > [ 0.286148] PnPBIOS: Disabled by ACPI PNP > [ 0.286148] PCI: Using ACPI for IRQ routing > [ 0.295447] system 00:01: ioport range 0xf50-0xf58 has been reserved > [ 0.295507] system 00:01: ioport range 0x408-0x40f has been reserved > [ 0.295564] system 00:01: ioport range 0x900-0x903 has been reserved > [ 0.295622] system 00:01: ioport range 0x904-0x904 has been reserved > [ 0.295680] system 00:01: ioport range 0x910-0x911 has been reserved > [ 0.295738] system 00:01: ioport range 0x920-0x923 has been reserved > [ 0.295796] system 00:01: ioport range 0x930-0x937 has been reserved > [ 0.295853] system 00:01: ioport range 0x940-0x947 has been reserved > [ 0.295911] system 00:01: ioport range 0x950-0x957 has been reserved > [ 0.295969] system 00:01: ioport range 0xc06-0xc08 has been reserved > [ 0.296027] system 00:01: ioport range 0xc14-0xc14 has been reserved > [ 0.296085] system 00:01: ioport range 0xc49-0xc4a has been reserved > [ 0.296142] system 00:01: ioport range 0xc50-0xc52 has been reserved > [ 0.296199] system 00:01: ioport range 0xc6c-0xc6f has been reserved > [ 0.296258] system 00:01: ioport range 0x230-0x233 has been reserved > [ 0.296315] system 00:01: ioport range 0x260-0x267 has been reserved > [ 0.296373] system 00:01: ioport range 0x4d0-0x4d1 has been reserved > [ 0.296431] system 00:01: ioport range 0x700-0x713 has been reserved > [ 0.296487] system 00:01: ioport range 0x800-0x81f has been reserved > [ 0.296545] system 00:01: ioport range 0xc80-0xc83 has been reserved > [ 0.298424] system 00:01: ioport range 0xcd4-0xcd7 has been reserved > [ 0.298482] system 00:01: ioport range 0xcf9-0xcf9 could not be reserved > [ 0.298542] system 00:01: ioport range 0x1900-0x1903 has been reserved > [ 0.329947] PCI: Bridge: 0000:00:07.0 > [ 0.330004] IO window: 3000-3fff > [ 0.330061] MEM window: 0xf7800000-0xf7bfffff > [ 0.330117] PREFETCH window: disabled. > [ 0.330174] PCI: Bridge: 0000:00:08.0 > [ 0.330227] IO window: 4000-4fff > [ 0.330283] MEM window: 0xf7c00000-0xf7ffffff > [ 0.330339] PREFETCH window: disabled. > [ 0.330459] NET: Registered protocol family 2 > [ 0.341936] IP route cache hash table entries: 32768 (order: 5, > 131072 bytes) > [ 0.342413] TCP established hash table entries: 131072 (order: 8, > 1048576 bytes) > [ 0.344098] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) > [ 0.344306] TCP: Hash tables configured (established 131072 bind 65536) > [ 0.344306] TCP reno registered > [ 0.349538] NET: Registered protocol family 1 > [ 0.349763] checking if image is initramfs... it is > [ 0.487730] Freeing initrd memory: 1838k freed > [ 0.489138] platform rtc_cmos: registered platform RTC device (no PNP > device found) > [ 0.493115] audit: initializing netlink socket (disabled) > [ 0.493115] type=2000 audit(1263974814.484:1): initialized > [ 0.493115] highmem bounce pool size: 64 pages > [ 0.493115] Total HugeTLB memory allocated, 0 > [ 0.493115] VFS: Disk quotas dquot_6.5.1 > [ 0.493115] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) > [ 0.493115] msgmni has been set to 1746 > [ 0.493115] Block layer SCSI generic (bsg) driver version 0.4 loaded > (major 253) > [ 0.493115] io scheduler noop registered > [ 0.493115] io scheduler anticipatory registered > [ 0.493115] io scheduler deadline registered > [ 0.493115] io scheduler cfq registered (default) > [ 0.493115] pci 0000:00:00.0: MSI quirk detected; MSI disabled > [ 0.493115] pci 0000:00:00.1: MSI quirk detected; MSI disabled > [ 0.493115] pci 0000:00:03.0: Boot video device > [ 0.507092] pci 0000:01:04.0: Firmware left e100 interrupts enabled; > disabling > [ 0.507177] pci 0000:01:05.0: Firmware left e100 interrupts enabled; > disabling > [ 0.507262] pci 0000:02:04.0: Firmware left e100 interrupts enabled; > disabling > [ 0.507346] pci 0000:02:05.0: Firmware left e100 interrupts enabled; > disabling > [ 0.509114] isapnp: Scanning for PnP cards... > [ 0.818524] isapnp: No Plug & Play device found > [ 0.821109] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ > sharing enabled > [ 0.821109] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A > [ 0.821109] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A > [ 0.825106] brd: module loaded > [ 0.825106] PNP: PS/2 Controller [PNP0303:KBD,PNP0f0e:PS2M] at > 0x60,0x64 irq 1,12 > [ 0.826135] serio: i8042 KBD port at 0x60,0x64 irq 1 > [ 0.826197] serio: i8042 AUX port at 0x60,0x64 irq 12 > [ 0.828749] mice: PS/2 mouse device common for all mice > [ 0.828749] rtc_cmos rtc_cmos: rtc core: registered rtc_cmos as rtc0 > [ 0.828749] rtc0: alarms up to one day > [ 0.831691] Switched to high resolution mode on CPU 1 > [ 0.832804] Switched to high resolution mode on CPU 0 > [ 0.844745] input: AT Translated Set 2 keyboard as /class/input/input0 > [ 0.844745] cpuidle: using governor ladder > [ 0.844745] cpuidle: using governor menu > [ 0.844745] No iBFT detected. > [ 0.844745] TCP cubic registered > [ 0.844745] NET: Registered protocol family 17 > [ 0.844745] Using IPI No-Shortcut mode > [ 0.844745] registered taskstats version 1 > [ 0.844745] rtc_cmos rtc_cmos: setting system clock to 2010-01-20 > 08:06:55 UTC (1263974815) > [ 0.844745] Freeing unused kernel memory: 244k freed > [ 0.912745] SCSI subsystem initialized > [ 0.916762] HP CISS Driver (v 3.6.20) > [ 0.916762] ACPI: PCI Interrupt 0000:00:06.0[A] -> GSI 21 (level, > low) -> IRQ 21 > [ 0.958551] cciss0: <0x46> at PCI 0000:00:06.0 IRQ 21 using DAC > [ 0.969814] blocks= 71119755 block_size= 512 > [ 0.973801] heads=255, sectors=63, cylinders=4427 > [ 0.973803] > [ 0.975277] blocks= 71119755 block_size= 512 > [ 0.975277] heads=255, sectors=63, cylinders=4427 > [ 0.975277] > [ 0.975277] cciss/c0d0: p1 p2 < p5 > > [ 1.003291] ACPI: ACPI0007:00 is registered as cooling_device0 > [ 1.003291] ACPI: ACPI0007:01 is registered as cooling_device1 > [ 1.007286] ACPI: LNXTHERM:01 is registered as thermal_zone0 > [ 1.007286] ACPI: Thermal Zone [THM0] (8 C) > [ 1.371292] PM: Starting manual resume from disk > [ 1.402844] kjournald starting. Commit interval 5 seconds > [ 1.402844] EXT3-fs: mounted filesystem with ordered data mode. > [ 2.517164] udevd version 125 started > [ 3.429486] Linux agpgart interface v0.103 > [ 3.461501] tg3.c:v3.92.1 (June 9, 2008) > [ 3.461591] ACPI: PCI Interrupt 0000:00:04.0[A] -> GSI 19 (level, > low) -> IRQ 19 > [ 3.504207] eth0: Tigon3 [partno(N/A) rev 1002 PHY(5703)] > (PCI:33MHz:32-bit) 10/100/1000Base-T Ethernet 00:11:85:69:7b:9a > [ 3.504315] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] > WireSpeed[1] TSOcap[1] > [ 3.504411] eth0: dma_rwctrl[763f0000] dma_mask[64-bit] > [ 3.516651] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 > [ 3.526127] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 > [ 3.605524] No dock devices found. > [ 3.654713] Emulex LightPulse Fibre Channel SCSI driver 8.2.6 > [ 3.654781] Copyright(c) 2004-2008 Emulex. All rights reserved. > [ 3.654902] ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 27 (level, > low) -> IRQ 27 > [ 3.696556] scsi0 : on PCI bus 00 device 48 irq 27 > [ 5.722476] libata version 3.00 loaded. > [ 5.736537] input: PC Speaker as /class/input/input1 > [ 5.814374] usbcore: registered new interface driver usbfs > [ 5.814485] usbcore: registered new interface driver hub > [ 5.857757] usbcore: registered new device driver usb > [ 5.862214] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller > (OHCI) Driver > [ 5.908648] input: Power Button (FF) as /class/input/input2 > [ 5.954659] ACPI: Power Button (FF) [PWRF] > [ 6.369720] input: ImPS/2 Generic Wheel Mouse as /class/input/input3 > [ 6.477188] Floppy drive(s): fd0 is 1.44M > [ 6.494944] FDC 0 is a National Semiconductor PC87306 > [ 6.589343] e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI > [ 6.589415] e100: Copyright(c) 1999-2006 Intel Corporation > [ 6.609750] Error: Driver 'pcspkr' is already registered, aborting... > [ 6.774218] parport_pc 00:07: reported by Plug and Play ACPI > [ 6.774218] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE] > [ 13.751240] lpfc 0000:00:09.0: 0:0442 Adapter failed to init, mbxCmd > x88 CONFIG_PORT, mbxStatus x12 Data: x0 > [ 18.555926] lpfc 0000:00:09.0: 0:0442 Adapter failed to init, mbxCmd > x88 CONFIG_PORT, mbxStatus x12 Data: x0 > [ 18.559835] ACPI: PCI interrupt for device 0000:00:09.0 disabled > [ 18.559835] piix4_smbus 0000:00:0f.0: Found 0000:00:0f.0 device > [ 18.924658] ACPI: PCI Interrupt Link [IUSB] enabled at IRQ 10 > [ 18.924754] ACPI: PCI Interrupt 0000:00:0f.2[A] -> Link [IUSB] -> GSI > 10 (level, low) -> IRQ 10 > [ 18.924962] ohci_hcd 0000:00:0f.2: OHCI Host Controller > [ 18.925500] ohci_hcd 0000:00:0f.2: new USB bus registered, assigned > bus number 1 > [ 18.925603] ohci_hcd 0000:00:0f.2: irq 10, io mem 0xf5f50000 > [ 18.981950] usb usb1: configuration #1 chosen from 1 choice > [ 18.982048] hub 1-0:1.0: USB hub found > [ 18.982115] hub 1-0:1.0: 4 ports detected > [ 19.093719] usb usb1: New USB device found, idVendor=1d6b, > idProduct=0001 > [ 19.093719] usb usb1: New USB device strings: Mfr=3, Product=2, > SerialNumber=1 > [ 19.093722] usb usb1: Product: OHCI Host Controller > [ 19.093776] usb usb1: Manufacturer: Linux 2.6.26-2-686 ohci_hcd > [ 19.093831] usb usb1: SerialNumber: 0000:00:0f.2 > [ 19.101835] ACPI: PCI Interrupt 0000:01:04.0[A] -> GSI 23 (level, > low) -> IRQ 23 > [ 19.201851] e100: eth1: e100_probe: addr 0xf7bf0000, irq 23, MAC addr > 00:02:a5:8e:ce:a6 > [ 19.201851] ACPI: PCI Interrupt 0000:01:05.0[A] -> GSI 24 (level, > low) -> IRQ 24 > [ 19.297833] e100: eth2: e100_probe: addr 0xf79f0000, irq 24, MAC addr > 00:02:a5:8e:ce:a7 > [ 19.297866] ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 25 (level, > low) -> IRQ 25 > [ 19.397831] e100: eth3: e100_probe: addr 0xf7ff0000, irq 25, MAC addr > 00:02:a5:89:86:92 > [ 19.397831] ACPI: PCI Interrupt 0000:02:05.0[A] -> GSI 26 (level, > low) -> IRQ 26 > [ 19.497848] e100: eth4: e100_probe: addr 0xf7df0000, irq 26, MAC addr > 00:02:a5:89:86:93 > [ 19.497848] Uniform Multi-Platform E-IDE driver > [ 19.497934] ide: Assuming 33MHz system bus speed for PIO modes; > override with idebus=xx > [ 19.507840] SvrWks CSB6: IDE controller (0x1166:0x0217 rev 0xa0) at > PCI slot 0000:00:0e.0 > [ 19.507840] SvrWks CSB6: not 100% native mode: will probe irqs later > [ 19.507840] ide2: BM-DMA at 0x2000-0x2007 > [ 19.507840] Probing IDE interface ide2... > [ 20.762833] hdf: LITE-ON DVD SOHD-16P9S, ATAPI CD/DVD-ROM drive > [ 21.150606] hdf: host max PIO4 wanted PIO255(auto-tune) selected PIO4 > [ 21.150690] hdf: UDMA/44 mode selected > [ 21.150881] ide2 at 0x1f0-0x1f7,0x3f6 on irq 14 > [ 21.234227] hdf: ATAPI 48X DVD-ROM drive, 254kB Cache > [ 21.234227] Uniform CD-ROM driver Revision: 3.20 > [ 21.875344] Adding 1510068k swap on /dev/cciss/c0d0p5. Priority:-1 > extents:1 across:1510068k > [ 22.220130] EXT3 FS on cciss/c0d0p1, internal journal > [ 22.690017] loop: module loaded > [ 24.737362] NET: Registered protocol family 10 > [ 24.738441] lo: Disabled Privacy Extensions > [ 24.738660] ADDRCONF(NETDEV_UP): eth0: link is not ready > [ 24.942663] tg3: eth0: Link is up at 100 Mbps, full duplex. > [ 24.942663] tg3: eth0: Flow control is on for TX and on for RX. > [ 24.942924] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready > [ 36.889054] eth0: no IPv6 routers present > > -- To UNSUBSCRIBE, email to debian-user-requ...@lists.debian.org with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
