I have a problem with my Debian Woody. I have the 2.4.18-bf2.4 kernel.
My computer set up is the following:
Asus A7S266-VM/U2
AMP XP 2400+
hda: 60 gb hard drive
hdc: creative cdrom 52X
hdd: samsung cdrw
I have two nic cards.
My motherboard's specs are:
North Bridge: SiS 740
South Bridge: SiS 962L
Integrated 4X AGP Graphics
2 x UltraDMA/133/100/66
C-Media 4-channel CODEC
S/PDIF-out interface
Lan: SiS 962L integrated 10/100Mbps Fast Ethernet with Realtek external PHY
My problem is the following:
Scenario 1:
I got my nic cards working and my sound to work if i add in the append section
of my lilo.conf file.
This is the line: append= "hdd=ide-scsi pci=bios"
But I can't get linux to detect the existence of my cdrom and cdrw (the bios
settings are correct, since they work perfectly under win98).
This is my dmesg output:
Linux version 2.4.18-bf2.4 ([EMAIL PROTECTED]) (gcc version 2.95.4 20011002 (Debian
prerelease)) #1 Son Apr 14 09:53:28 CEST 2002
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000dffc000 (usable)
BIOS-e820: 000000000dffc000 - 000000000dfff000 (ACPI data)
BIOS-e820: 000000000dfff000 - 000000000e000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
On node 0 totalpages: 57340
zone(0): 4096 pages.
zone(1): 53244 pages.
zone(2): 0 pages.
Found and enabled local APIC!
Kernel command line: BOOT_IMAGE=Linux ro root=306 hdd=ide-scsi
pci=bios,biosirq
ide_setup: hdd=ide-scsi
Initializing CPU#0
Detected 1513.504 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 3021.20 BogoMIPS
Memory: 222432k/229360k available (1783k kernel code, 6540k reserved, 549k
data, 280k init, 0k highmem)
Dentry-cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
CPU: Before vendor init, caps: 0383fbff c1c3fbff 00000000, vendor = 2
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After vendor init, caps: 0383fbff c1c3fbff 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383fbff c1c3fbff 00000000 00000000
CPU: Common caps: 0383fbff c1c3fbff 00000000 00000000
CPU: AMD Athlon(TM) XP 2400+ stepping 01
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1513.5281 MHz.
..... host bus clock speed is 201.8038 MHz.
cpu: 0, clocks: 2018038, slice: 1009019
CPU0<T0:2018032,T1:1009008,D:5,S:1009019,C:2018038>
mtrr: v1.40 (20010327) Richard Gooch ([EMAIL PROTECTED])
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xf18e0, last bus=1
PCI: Probing PCI hardware
PCI: Using IRQ router default [1039/0962] at 00:02.0
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Diskquotas version dquot_6.4.0 initialized
Journalled Block Device driver loaded
vga16fb: initializing
vga16fb: mapped to 0xc00a0000
Console: switching to colour frame buffer device 80x30
fb0: VGA16 VGA frame buffer device
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI
enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10e
block: 128 slots per queue, batch=32
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SIS5513: IDE controller on PCI bus 00 dev 15
SIS5513: chipset revision 0
SIS5513: not 100% native mode: will probe irqs later
SiS740
ide0: BM-DMA at 0xa400-0xa407, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xa408-0xa40f, BIOS settings: hdc:DMA, hdd:DMA
hda: WDC WD600AB-00BVA0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: 117231408 sectors (60022 MB) w/2048KiB Cache, CHS=7297/255/63, UDMA(100)
ide-floppy driver 0.97.sv
Partition check:
hda: hda1 hda2 < hda5 hda6 hda7 hda8 hda9 hda10 > hda3 hda4
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Loading I2O Core - (c) Copyright 1999 Red Hat Software
I2O configuration manager v 0.04.
(C) Copyright 1999 Red Hat Software
loop: loaded (max 8 devices)
Compaq CISS Driver (v 2.4.5)
8139cp 10/100 PCI Ethernet driver v0.0.6 (Nov 19, 2001)
8139cp: pci dev 00:10.0 (id 10ec:8139 rev 10) is not an 8139C+ compatible chip
8139cp: Try the "8139too" driver instead.
8139too Fast Ethernet driver 0.9.24
eth0: D-Link DFE-538TX (RealTek RTL8139) at 0xce81a000, 00:40:05:0c:f1:56, IRQ
11
eth0: Identified 8139 chip type 'RTL-8139C'
eth1: RealTek RTL8139 Fast Ethernet at 0xce81c000, 00:e0:7d:d6:4d:e7, IRQ 7
eth1: Identified 8139 chip type 'RTL-8139C'
HDLC support module revision 1.02 for Linux 2.4
Cronyx Ltd, Synchronous PPP and CISCO HDLC (c) 1994
Linux port (c) 1998 Building Number Three Ltd & Jan "Yenya" Kasprzak.
ide-floppy driver 0.97.sv
Promise Fasttrak(tm) Softwareraid driver 0.03beta: No raid array found
Highpoint HPT370 Softwareraid driver for linux version 0.01
No raid array found
SCSI subsystem driver Revision: 1.00
Red Hat/Adaptec aacraid driver, Apr 14 2002
DC390: 0 adapters found
3ware Storage Controller device driver for Linux v1.02.00.016.
3w-xxxx: No cards with valid units found.
request_module[scsi_hostadapter]: Root fs not mounted
request_module[scsi_hostadapter]: Root fs not mounted
i2o_scsi.c: Version 0.0.1
chain_pool: 0 bytes @ cdff8be0
(512 byte buffers X 4 can_queue X 0 i2o controllers)
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 16384)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
cramfs: wrong magic
FAT: bogus logical sector size 0
reiserfs: checking transaction log (device 03:06) ...
Warning, log replay starting on readonly filesystem
Using r5 hash to sort names
ReiserFS version 3.6.25
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 280k freed
Adding Swap: 248936k swap-space (priority -1)
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-ohci.c: USB OHCI at membase 0xce8ff000, IRQ 5
usb-ohci.c: usb-00:03.0, Silicon Integrated Systems [SiS] 7001
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 3 ports detected
usb-ohci.c: USB OHCI at membase 0xce901000, IRQ 9
usb-ohci.c: usb-00:03.1, Silicon Integrated Systems [SiS] 7001 (#2)
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 3 ports detected
usb.c: registered new driver keyboard
usbkbd.c: :USB HID Boot Protocol keyboard driver
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8 Andreas Gal, Vojtech Pavlik <[EMAIL PROTECTED]>
hid-core.c: USB HID support drivers
Intel 810 + AC97 Audio, version 0.21, 10:28:09 Apr 14 2002
i810: SiS 7012 found at IO 0x9000 and 0x9400, IRQ 10
i810_audio: Audio Controller supports 6 channels.
ac97_codec: AC97 codec, id: 0x434d:0x4941 (Unknown)
i810_audio: only 48Khz playback available.
i810_audio: AC'97 codec 0 Unable to map surround DAC's (or DAC's not present),
total channels = 2
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
reiserfs: checking transaction log (device 03:07) ...
Using r5 hash to sort names
ReiserFS version 3.6.25
reiserfs: checking transaction log (device 03:08) ...
Using r5 hash to sort names
ReiserFS version 3.6.25
reiserfs: checking transaction log (device 03:09) ...
Using r5 hash to sort names
ReiserFS version 3.6.25
reiserfs: checking transaction log (device 03:0a) ...
Using r5 hash to sort names
ReiserFS version 3.6.25
reiserfs: checking transaction log (device 03:04) ...
spurious 8259A interrupt: IRQ7.
Using r5 hash to sort names
ReiserFS version 3.6.25
eth0: Setting half-duplex based on auto-negotiated partner ability 0000.
eth1: Setting half-duplex based on auto-negotiated partner ability 0000.
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack (1791 buckets, 14328 max)
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
lp: driver loaded but no devices found
eth0: Promiscuous mode enabled.
device eth0 entered promiscuous mode
Warning: Remapping obsolete /dev/fb* minor 32 to 1
Warning: Remapping obsolete /dev/fb* minor 64 to 2
Warning: Remapping obsolete /dev/fb* minor 96 to 3
Warning: Remapping obsolete /dev/fb* minor 128 to 4
Warning: Remapping obsolete /dev/fb* minor 160 to 5
Warning: Remapping obsolete /dev/fb* minor 192 to 6
Warning: Remapping obsolete /dev/fb* minor 224 to 7
This is my lspci -vv output:
henry:/home/henry# lspci -vv
00:00.0 Host bridge: Silicon Integrated Systems [SiS]: Unknown device 0740
(rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 32
Region 0: Memory at e8000000 (32-bit, non-prefetchable) [size=64M]
Capabilities: [c0] AGP version 2.0
Status: RQ=16 SBA+ 64bit- FW+ Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
00:01.0 PCI bridge: Silicon Integrated Systems [SiS] 5591/5592 AGP (prog-if 00
[Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: e7800000-e7ffffff
Prefetchable memory behind bridge: f0000000-febfffff
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
00:02.0 ISA bridge: Silicon Integrated Systems [SiS]: Unknown device 0962 (rev
25)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (prog-if 8a
[Master SecP PriP])
Subsystem: Asustek Computer, Inc.: Unknown device 8084
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 16
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at <ignored>
Region 1: I/O ports at <ignored>
Region 2: I/O ports at <ignored>
Region 3: I/O ports at <ignored>
Region 4: I/O ports at a400 [size=16]
00:02.7 Multimedia audio controller: Silicon Integrated Systems [SiS] SiS7012
PCI Audio Accelerator (rev a0)
Subsystem: Asustek Computer, Inc.: Unknown device 8091
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (13000ns min, 2750ns max)
Interrupt: pin C routed to IRQ 10
Region 0: I/O ports at 9400 [size=256]
Region 1: I/O ports at 9000 [size=128]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=55mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:03.0 USB Controller: Silicon Integrated Systems [SiS] 7001 (rev 0f)
(prog-if 10 [OHCI])
Subsystem: Asustek Computer, Inc.: Unknown device 8084
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (20000ns max), cache line size 08
Interrupt: pin A routed to IRQ 5
Region 0: Memory at e7000000 (32-bit, non-prefetchable) [size=4K]
00:03.1 USB Controller: Silicon Integrated Systems [SiS] 7001 (rev 0f)
(prog-if 10 [OHCI])
Subsystem: Asustek Computer, Inc.: Unknown device 8084
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (20000ns max), cache line size 08
Interrupt: pin B routed to IRQ 9
Region 0: Memory at e6800000 (32-bit, non-prefetchable) [size=4K]
00:03.3 USB Controller: Silicon Integrated Systems [SiS]: Unknown device 7002
(prog-if 20)
Subsystem: Asustek Computer, Inc.: Unknown device 8084
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (20000ns max), cache line size 08
Interrupt: pin D routed to IRQ 9
Region 0: Memory at e6000000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0d.0 Ethernet controller: D-Link System Inc RTL8139 Ethernet (rev 10)
Subsystem: D-Link System Inc: Unknown device 1301
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 8400 [size=256]
Region 1: Memory at e5000000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139 (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 7
Region 0: I/O ports at 8000 [size=256]
Region 1: Memory at e4800000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: Silicon Integrated Systems [SiS]: Unknown
device 6325 (prog-if 00 [VGA])
Subsystem: Asustek Computer, Inc.: Unknown device 80a0
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
BIST result: 00
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
Region 1: Memory at e7800000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at d800 [size=128]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] AGP version 2.0
Status: RQ=15 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
This also might help:
henry:/home/henry# cat /proc/devices
Character devices:
1 mem
2 pty
3 ttyp
4 ttyS
5 cua
6 lp
7 vcs
10 misc
13 input
14 sound
29 fb
128 ptm
136 pts
162 raw
180 usb
Block devices:
1 ramdisk
2 fd
3 ide0
7 loop
114 ataraid
Now if I change the line in my lilo.conf file to:
append= "hdd=ide-scsi pci=biosirq"
Linux sees the cdrom and cdrw, but then the two nic cards dont work and I get
no sound.
I've also tried:
append= "hdd=ide-scsi pci=bios,biosirq"
The result is the same as the first scenario. I get the two nic cards to work
correctly and the sound. But I can't get my cdrom and cdrw to work.
Can anyone tell me what to do. I've read A LOT and I can't figure out how to
solve this. Should I change my kernel?? Is there another option to append???
I need help please.
Thank you.
Henry
PS: Sorry about the long mail.
--
To UNSUBSCRIBE, email to [EMAIL PROTECTED]
with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
