I use Etch, and I hibernate my computer with userspace suspend (uswsusp) and hibernate packages. It generally works, but sometimes after the computer resumed, networking restarts. ( and my X session, too). What is the problem? Thanks.
dmesg: [...] Freezing cpus ... Stopping tasks: ============================================================== ==============================================================================| Shrinking memory... done (107919 pages freed) pnp: Device 00:0c disabled. pnp: Device 00:08 disabled. pnp: Device 00:07 disabled. ACPI: PCI interrupt for device 0000:00:1f.5 disabled ACPI: PCI interrupt for device 0000:00:1f.4 disabled ACPI: PCI interrupt for device 0000:00:1f.2 disabled .... swsusp: Need to copy 111050 pages Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU0: Intel P4/Xeon Extended MCE MSRs (12) available CPU0: Thermal monitoring enabled swsusp: Restoring Highmem ACPI: Unable to turn cooling device [c18fbf04] 'on' PCI: Setting latency timer of device 0000:00:1e.0 to 64 PCI: Enabling device 0000:00:1f.2 (0000 -> 0001) ACPI: PCI Interrupt 0000:00:1f.2[D] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:00:1f.2 to 64 PCI: Enabling device 0000:00:1f.4 (0000 -> 0001) ACPI: PCI Interrupt 0000:00:1f.4[C] -> Link [LNK1] -> GSI 9 (level, low) -> IRQ 9 PCI: Setting latency timer of device 0000:00:1f.4 to 64 PM: Writing back config space on device 0000:00:1f.5 at offset 1 (was 2800005, writing 2800000) PCI: Enabling device 0000:00:1f.5 (0000 -> 0001) ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 7 (level, low) -> IRQ 7 PCI: Setting latency timer of device 0000:00:1f.5 to 64 PM: Writing back config space on device 0000:02:01.0 at offset 1 (was 2100007, writing 2100000) pnp: Device 00:07 activated. pnp: Device 00:08 activated. pnp: Failed to activate device 00:09. pnp: Failed to activate device 00:0a. pnp: Device 00:0c activated. Restarting tasks... done Thawing cpus ... via-rhine.c:v1.10-LK1.4.1 July-24-2006 Written by Donald Becker PCI: Enabling device 0000:02:01.0 (0000 -> 0003) ACPI: PCI Interrupt 0000:02:01.0[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11 eth0: VIA Rhine II at 0x1c000, 00:e0:4c:99:08:13, IRQ 11. eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 41e1. logips2pp: Detected unknown logitech mouse model 0 ACPI: Power Button (FF) [PWRF] ACPI: Power Button (CM) [PWRB] input: ImPS/2 Logitech Wheel Mouse as /class/input/input9 eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 bridge-eth0: enabling the bridge bridge-eth0: up eth0: no IPv6 routers present [...] -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
