Hi all- I've got a weird problem with a recently acquired Dell Inspiron 2650 laptop's Synaptics touchpad I'm hoping someone can shed light on. I can provide more info on request, just the basics here.
I installed the recent Lenny netinstall and immediately noticed that the touchpad was quite sluggish. Worse, it seems to "click" buttons and "select" menus in an out-of-control fashion, without my touching the pad's two buttons, just the touchpad XY surface. Installed kSynaptics to no effect, removed gpm to no effect. I thought it must be a worn-out touchpad and actually bought another one, but serendipitously, as I was booting a FireWire CD-ROM burner via a FireWire PCMCIA card, the touchpad worked flawlessly. The mount of the FireWire burner actually failed gracefully, as I think I need SCSI CD-ROM support or something in the kernel. The touchpad only works flawlessly when I boot the failing burner. A working FireWire disk, successfully mounted, lets the touchpad be its old bad self. So I'm really unclear what the presence of failing FireWire device might have on the touchpad's behavior. An inspection of the /proc, etc. areas that are suggested in much of the synaptics trouble/configuration help around the net don't reveal anything out of the ordinary. Here is the DIFF of the dmesg file of the two boots: one with the failing 1394 device that causes the touchpad to behave, the other a boot where the touchpad works crazily. (On this boot, the main HD was checked by fsck) Anyone have any thoughts on how to proceed with this? Many thanks in advance! Charles . . . . . 1c1 < 0000:02:01.0: 3Com PCI 3c905C Tornado at d481c000. --- > 0000:02:01.0: 3Com PCI 3c905C Tornado at d4816000. 22d21 < ACPI: PCI Interrupt 0000:03:00.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10 48c47 < audit(1191602477.648:1): initialized --- > audit(1191603389.648:1): initialized 65c64 < Calibrating delay using timer specific routine.. 3194.26 BogoMIPS (lpj=6388522) --- > Calibrating delay using timer specific routine.. 3194.31 BogoMIPS (lpj=6388622) 99,103d97 < cs: memory probe 0x20000000-0x25ffffff: excluding 0x20000000-0x25ffffff < cs: memory probe 0x60000000-0x60ffffff: excluding 0x60000000-0x60ffffff < cs: memory probe 0xa0000000-0xa0ffffff: excluding 0xa0000000-0xa0ffffff < cs: memory probe 0xe8000000-0xe80fffff: excluding 0xe8000000-0xe80fffff < cs: warning: no high memory space available! 106c100 < Detected 1595.327 MHz processor. --- > Detected 1595.340 MHz processor. 120,121d113 < eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0) < EXT3-fs: INFO: recovery required on readonly filesystem. 124,125d115 < EXT3-fs: recovery complete. < EXT3-fs: write access will be enabled during recovery. 153,155d142 < ieee1394: Error parsing configrom for node 0-00:1023 < ieee1394: Host added: ID:BUS[0-01:1023] GUID[0011060000003445] < ieee1394: Initialized config rom entry `ip1394' 165c152 < intel8x0_measure_ac97_clock: measured 55364 usecs --- > intel8x0_measure_ac97_clock: measured 55347 usecs 210d196 < ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[10] MMIO=[28000000-280007ff] Max Packet=[1024] IR/IT contexts=[4/8] 214d199 < pccard: CardBus card inserted into slot 0 220d204 < PCI: Enabling device 0000:03:00.0 (0080 -> 0083) 234d217 < PCI: Setting latency timer of device 0000:03:00.0 to 64 274c257 < Socket status: 30000821 --- > Socket status: 30000007 308c291 < Yenta: ISA IRQ mask 0x0038, PCI irq 10 --- > Yenta: ISA IRQ mask 0x00b8, PCI irq 10 -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
