Hello,
After the recent udev + hdparm problems, I'm thinking
of reconfiguring hdparm (hdparm currently is not
configured, just reinstalled, so I'm assuming it's
currently using default settings)
This is the output of `hdparm -v -i /dev/hda`:
/dev/hda:
multcount = 0 (off)
IO_support = 1 (32-bit)
unmaskirq = 1 (on)
using_dma = 0 (off)
keepsettings = 0 (off)
readonly = 0 (off)
readahead = 256 (on)
geometry = 65535/16/63, sectors = 78165360, start
= 0
Model=IC35L040AVER07-0, FwRev=ER4OA46A,
SerialNo=SXPTX283824
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs
}
RawCHS=16383/16/63, TrkSize=0, SectSize=0,
ECCbytes=40
BuffType=DualPortCache, BuffSize=1916kB,
MaxMultSect=16, MultSect=off
CurCHS=4047/16/255, CurSects=16511760, LBA=yes,
LBAsects=78165360
IORDY=on/off, tPIO={min:240,w/IORDY:120},
tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
udma3 udma4 *udma5
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: ATA/ATAPI-5 T13 1321D revision 1:
ATA/ATAPI-2 ATA/ATAPI-3 ATA/ATAPI-4 ATA/ATAPI-5
* signifies the current active mode
/dev/hdb:
multcount = 0 (off)
IO_support = 1 (32-bit)
unmaskirq = 1 (on)
using_dma = 0 (off)
keepsettings = 0 (off)
readonly = 0 (off)
readahead = 256 (on)
geometry = 65535/16/63, sectors = 80293248, start
= 0
Model=Maxtor 2F040J0, FwRev=VAM51JJ0,
SerialNo=F10SPCNE
Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0,
ECCbytes=57
BuffType=DualPortCache, BuffSize=2048kB,
MaxMultSect=16, MultSect=off
CurCHS=4047/16/255, CurSects=16511760, LBA=yes,
LBAsects=80293248
IORDY=on/off, tPIO={min:120,w/IORDY:120},
tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 udma5 udma3
udma4 udma5 *udma6
AdvancedPM=yes: disabled (255) WriteCache=enabled
Drive conforms to: ATA/ATAPI-7 T13 1532D revision 0:
ATA/ATAPI-1 ATA/ATAPI-2 ATA/ATAPI-3 ATA/ATAPI-4
ATA/ATAPI-5 ATA/ATAPI-6 ATA/ATAPI-7
* signifies the current active mode
Could someone tell me what settings are appropiate for
my hard discs? I tried before with, what didn't really
seem to push things, but problems with modules not
loading reappeared
Thanks,
Joris
____________________________________________________________________________________
Building a website is a piece of cake. Yahoo! Small Business gives you all the
tools to get online.
http://smallbusiness.yahoo.com/webhosting
--
To UNSUBSCRIBE, email to [EMAIL PROTECTED]
with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
