Hi Mike Messick, Maybe you should try with kernel parameter "irqpoll"
Goodluck Thang Kieu Mike Messick wrote: > Hi Folks, > > I'm using the latest debian-testing-amd64-businesscard installer on an > Asus P5K motherboard with an ICH9 Southbridge and Marvell 88SE61xx SATA / > PATA chipset. I'm using an HP dvd1040i CDrom drive for installation. > > The installer boots fine but cannot find any cdrom device to use. When I > look at dmesg, I get the following output relating to the ide devices: > > Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 > ide: Assuming 33MHZ system bus speed for PIO modes; override with > idebus=xx > pnp: the driver 'ide' has been registered > ata_piix: 0000:00:1f.2: version 2.10ac1 > ata_piix: 0000:00:1f.2: MAP [ P0 P2 P1 P3 ] > ata1: SATA max UDMA/133 cmd 0x00000000000101f0 ctl 0x00000000000103f6 > bmdma 0x000000000001ff90 irq 14 > ata1: SATA max UDMA/133 cmd 0x00000000000101f0 ctl 0x0000000000010376 > bmdma 0x000000000001ff98 irq 15 > scsi0: ata_piix > ata1.00: ATA-7: ST3500630AS, 3.AAK, max UDMA/133 > ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32) > ata1.00: configured for UDMA/133 > scsi1: ata_piix > ata2.00: ATA-7: ST3500630AS, 3.AAK, max UDMA/133 > ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32) > ata2.00: configured for UDMA/133 > scsi: 0:0:0:0: Direct-Access ATA ST3500630AS 3.AA PQ: 0 ANSI: 5 > scsi: 1:0:0:0: Direct-Access ATA ST3500630AS 3.AA PQ: 0 ANSI: 5 > ata_piix 0000:00:1f.5: MAP [ P0 P2 P1 P3 ] > ata3: SATA max UDMA/133 cmd 0x000000000001a000 ctl 0x0000000000019c02 > bmdma 0x0000000000019480 irq 22 > ata4: SATA max UDMA/133 cmd 0x0000000000019880 ctl 0x0000000000019802 > bmdma 0x0000000000019488 irq 22 > scsi2: ata_piix > ATA: abnormal status 0x7F on port 0x000000000001a007 > scsi3: ata_piix > ATA: abnormal status 0x7F on port 0x0000000000019887 > SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB) > sda: Write protect is off > sda: Mode Sense: 00 3a 00 00 > SCSI device sda: write cache: enabled, read cache: enabled, doesn't > support DPO or FUA > SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB) > sda: Write protect is off > sda: Mode Sense: 00 3a 00 00 > SCSI device sda: write cache: enabled, read cache: enabled, doesn't > support DPO or FUA > sda: unknown partition table > sd: 0:0:0:0: Attached scsi disk sda > SCSI device sdb: 976773168 512-byte hdwr sectors (500108 MB) > sdb: Write protect is off > sdb: Mode Sense: 00 3a 00 00 > SCSI device sdb: write cache: enabled, read cache: enabled, doesn't > support DPO or FUA > SCSI device sdb: 976773168 512-byte hdwr sectors (500108 MB) > sdb: Write protect is off > sdb: Mode Sense: 00 3a 00 00 > SCSI device sdb: write cache: enabled, read cache: enabled, doesn't > support DPO or FUA > sdb: unknown partition table > sd: 1:0:0:0: Attached scsi disk sdb > ide0: I/O resource 0x3F6-0x3F6 not free. > ide0: ports already in use, skipping probe > ide1: I/O resource 0x376-0x376 not free. > ide1: ports already in use, skipping probe > > an lspci yields the following IDE devices: > > 00:1f.2 IDE interface: Intel Corporation Unknown device 2920 (rev 02) > (prog-if 8a [Master SecP PriP]) > Subsystem: ASUSTeK Computer Inc. Unknown device 8277 > Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 22 > I/O ports at 01f0 [size=8] > I/O ports at 03f4 [size=1] > I/O ports at 0170 [size=8] > I/O ports at 0374 [size=1] > I/O ports at ff90 [size=16] > I/O ports at ffa0 [size=16] > Capabilities: [70] Power Management version 3 > Capabilities: [b0] Vendor Specific Information > > 00:1f.5 IDE interface: Intel Corporation Unknown device 2926 (rev 02) > (prog-if 85 [Master SecO PriO]) > Subsystem: ASUSTeK Computer Inc. Unknown device 8277 > Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 22 > I/O ports at a000 [size=8] > I/O ports at 9c00 [size=4] > I/O ports at 9880 [size=8] > I/O ports at 9800 [size=4] > I/O ports at 9480 [size=16] > I/O ports at 9400 [size=16] > Capabilities: [70] Power Management version 3 > Capabilities: [b0] Vendor Specific Information > > 01:00.0 IDE interface: Marvell Technology Group Ltd. Unknown device 6121 > (rev b1) (prog-if 8f [Master SecP SecO PriP PriO]) > Subsystem: ASUSTeK Computer Inc. Unknown device 8296 > Flags: bus master, fast devsel, latency 0, IRQ 10 > I/O ports at bc00 [size=8] > I/O ports at b880 [size=4] > I/O ports at b800 [size=8] > I/O ports at b480 [size=16] > I/O ports at b400 [size=16] > Memory at fe7ffc00 (32-bit, non-prefetchable) [size=1K] > Capabilities: [48] Power Management version 2 > Capabilities: [50] Messsage Signalled Interrupts: Mask- 64bit- Queue=0/0 > Enable- > Capabilities: [e0] Express Legacy Endpoint IRQ 0 > > So it looks like my 2 hard drives are showing up just fine, but I'm fairly > clueless as to why the kernel (2.6.21-2-amd64) isn't finding the CDrom > drive. > > I've verified that the Marvell IDE/eSATA controller is enabled in the BIOS > as well (hence the initial booting of the installer CD). > > I'm hoping someone on the list can point me in the right direction; if > this isn't the appropriate list then please accept my apologies for the > noise. > > Thanks in advance, > -Mike. > > ================================================================== > Mike Messick Dona nobis pacem rm -rf /bin/laden > PGP Key Fingerprint: email: [EMAIL PROTECTED] > 2048/0x57318496 053B 412B 82FC 3808 E141 CDCD 74AE 01C5 5731 8496 > > > -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
