[EMAIL PROTECTED], 2002-May-31 22:59 -0300: > Hi guys, I'm having some problems with pppd. I'm trying to install 2 servers > with a leased line. > > All signals (DCD, DSR, DTR, CTS and RTS) are up, which indcates that the > cables and modems are OK, but I can't ping the remote peer. > > Here goes my configurations: > > Server 1: > > Kernel IP routing table > Destination Gateway Genmask Flags Metric Ref Use > Iface > 192.168.100.2 192.168.100.1 255.255.255.255 UGH 0 0 0 ppp0 > 200.216.95.214 0.0.0.0 255.255.255.255 UH 0 0 0 ppp1 > 192.168.100.0 0.0.0.0 255.255.255.252 U 0 0 0 ppp0 > 10.0.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 > 0.0.0.0 200.216.95.214 0.0.0.0 UG 0 0 0 ppp1
>From this system, can you ping the local interface 192.168.100.1? If so, then can you ping the remote interface 192.168.100.2? If so, and you can't ping anything beyond 192.168.100.2 then there's a routing problem on the remote server. If you try to ping a host on the 10.0.1.0 network, the ping will take the default route which is ppp1 (200.216.95.214) and it doesn't appear that this is the correct path. Also, if you ping any other host on the 192.168.100.0 network, that ping will take the default route ppp1, and it appears that is not correct either. You need to point all the newtorks/hosts you want to go to the remote end to the 192.168.100.2 gateway, e.g. 192.168.100.2 192.168.100.1 255.255.255.255 UGH 0 0 0 ppp0 200.216.95.214 0.0.0.0 255.255.255.255 UH 0 0 0 ppp1 192.168.100.0 192.168.100.1 255.255.255.252 U 0 0 0 ppp0 10.0.1.0 192.168.100.1 255.255.255.0 U 0 0 0 eth1 0.0.0.0 200.216.95.214 0.0.0.0 UG 0 0 0 ppp1 So, 10.0.1.0 and 192.168.100.0-2 will go to the remote server and all else will go to the default, ppp1. > Server 2: > > Kernel IP routing table > Destination Gateway Genmask Flags Metric Ref Use > Iface > 192.168.100.1 192.168.100.2 255.255.255.255 UGH 0 0 0 ppp0 > 192.168.100.0 0.0.0.0 255.255.255.252 U 0 0 0 ppp0 > 10.0.4.0 0.0.0.0 255.255.255.0 U 0 0 0 eth2 > 10.0.1.0 192.168.100.2 255.255.255.0 UG 0 0 0 ppp0 > 10.0.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 > 10.0.3.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 > 0.0.0.0 192.168.100.2 0.0.0.0 UG 0 0 0 ppp0 This side looks right to me. I hope this helps...jc -- Jeff Coppock Systems Engineer Diggin' Debian Admin and User -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
