I have been running a version of woody from Feb 28, 2002 on a 686
machine using the 2.2.19 kernel that was installed from a potato cdrom
set and then the software was updated from another cdrom set to
woody. Everything was working fine for many days, but xcdroast
complained about cdrecord not working since it needed a 2.4 kernel.
So finally tonight I did an apt-get install kernel-2.4.17-686 and that
went fine and is what I'm using now. HOWEVER, when I try to access the
cdrom drive I get the following in dmesg:
Linux version 2.4.17-686 ([EMAIL PROTECTED]) (gcc version 2.95.4 20011006
(Debian prerelease)) #2 Sat Dec 22 21:58:49 EST 2001
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ffec000 (usable)
BIOS-e820: 000000001ffec000 - 000000001ffef000 (ACPI data)
BIOS-e820: 000000001ffef000 - 000000001ffff000 (reserved)
BIOS-e820: 000000001ffff000 - 0000000020000000 (ACPI NVS)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
On node 0 totalpages: 131052
zone(0): 4096 pages.
zone(1): 126956 pages.
zone(2): 0 pages.
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
Kernel command line: auto BOOT_IMAGE=Linux ro root=301 hdd=ide-scsi
Initializing CPU#0
Detected 999.752 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 1992.29 BogoMIPS
Memory: 510876k/524208k available (808k kernel code, 12944k reserved, 233k
data, 208k init, 0k highmem)
Dentry-cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: Before vendor init, caps: 0383fbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After vendor init, caps: 0383fbff 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
CPU: Intel Pentium III (Coppermine) stepping 06
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000040
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 999.7457 MHz.
..... host bus clock speed is 133.2993 MHz.
cpu: 0, clocks: 1332993, slice: 666496
CPU0<T0:1332992,T1:666496,D:0,S:666496,C:1332993>
mtrr: v1.40 (20010327) Richard Gooch ([EMAIL PROTECTED])
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xf0d20, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unknown bridge resource 0: assuming transparent
PCI: Using IRQ router VIA [1106/0686] at 00:04.0
PCI: Disabling Via external APIC routing
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Diskquotas version dquot_6.4.0 initialized
devfs: v1.7 (20011216) Richard Gooch ([EMAIL PROTECTED])
devfs: boot_options: 0x0
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT
SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
PCI: Found IRQ 9 for device 00:07.0
Redundant entry in serial pci_table. Please send the output of
lspci -vv, this message (12b9,1008,12b9,00a2)
and the manufacturer and name of serial board or modem board
to [EMAIL PROTECTED]
ttyS04 at port 0xb800 (irq = 9) is a 16550A
block: 128 slots per queue, batch=32
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Cronyx Ltd, Synchronous PPP and CISCO HDLC (c) 1994
Linux port (c) 1998 Building Number Three Ltd & Jan "Yenya" Kasprzak.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
Linux IP multicast router 0.06 plus PIM-SM
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 3220 blocks [1 disk] into ram disk... done.
Freeing initrd memory: 3220k freed
VFS: Mounted root (cramfs filesystem).
Journalled Block Device driver loaded
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller on PCI bus 00 dev 21
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci00:04.1
ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:DMA, hdd:DMA
hda: IC35L040AVER07-0, ATA DISK drive
hdc: Pioneer DVD-ROM ATAPIModel DVD-106S 010, ATAPI CD/DVD-ROM drive
hdd: PLEXTOR CD-R PX-W1610A, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 80418240 sectors (41174 MB) w/1916KiB Cache, CHS=79780/16/63
Partition check:
/dev/ide/host0/bus0/target0/lun0: [PTBL] [5005/255/63] p1 p2 p3 < p5 p6 >
cramfs: wrong magic
VFS: Mounted root (ext2 filesystem) readonly.
change_root: old root has d_count=2
Freeing unused kernel memory: 208k freed
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Adding Swap: 996020k swap-space (priority -1)
Real Time Clock Driver v1.10e
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: PIONEER Model: DVD-ROM DVD-106 Rev: 1.08
Type: CD-ROM ANSI SCSI revision: 02
Vendor: PLEXTOR Model: CD-R PX-W1610A Rev: 1.02
Type: CD-ROM ANSI SCSI revision: 02
Creative EMU10K1 PCI Audio Driver, version 0.16, 17:39:46 Dec 22 2001
PCI: Found IRQ 5 for device 00:08.0
PCI: Sharing IRQ 5 with 01:00.0
emu10k1: EMU10K1 rev 7 model 0x8027 found, IO at 0xb400-0xb41f, IRQ 5
ac97_codec: AC97 Audio codec, id: 0x4352:0x5914 (Cirrus Logic CS4297A rev B)
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: Printer, Hewlett-Packard HP LaserJet 1200
parport_pc: Via 686A parallel port: io=0x378
lp0: using parport0 (polling).
lp0: compatibility mode
VFS: Disk change detected on device ide1(22,0)
ide-scsi: hdc: unsupported command in request queue (0)
end_request: I/O error, dev 16:00 (hdc), sector 64
isofs_read_super: bread failed, dev=16:00, iso_blknum=16, block=32
VFS: Disk change detected on device ide1(22,0)
ide-scsi: hdc: unsupported command in request queue (0)
end_request: I/O error, dev 16:00 (hdc), sector 64
isofs_read_super: bread failed, dev=16:00, iso_blknum=16, block=32
My lilo.conf has append="hdd=ide-scsi" in it.
My question is: what did I hose in updating the kernel since it is
most unhappy with hdc??
Thanks for any advice.
--
Ed Kleckner, N7YQR L I N U X .~.
Hansville, WA The Choice /V\
of a GNU /( )\
Generation ^^-^^
--
To UNSUBSCRIBE, email to [EMAIL PROTECTED]
with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
