If that doesn't work, you could try 'alias eth0 3c59x'
-----Original Message----- From: Michael Marziani [mailto:[EMAIL PROTECTED] Sent: Thursday, April 19, 2001 12:40 PM To: 'Randall Hansen'; 'debian-user@lists.debian.org' Subject: RE: [debian-users] 3Com 3c900 NIC troubles I'm not sure how linuxconf works on debian (I actually hadn't used it since I switched from redhat). I'm still learning about the whole Debian subculture, but I think the "Debian way" is to just edit the files directly. As I've begun to do that more I feel like I understand the system a lot better anyway. That aside, the modules file you are looking for is /etc/modules. My /etc/modules looks like: # /etc/modules: kernel modules to load at boot time. # # This file should contain the names of kernel modules that are # to be loaded at boot time, one per line. Comments begin with # a #, and everything on the line after them are ignored. 3c59x Pretty simple. Of course I'm using a 3c905c, but I would think yours would work too. Hope this helps! -Mike -----Original Message----- From: Randall Hansen [mailto:[EMAIL PROTECTED] Sent: Thursday, April 19, 2001 10:31 AM To: debian-user@lists.debian.org Subject: [debian-users] 3Com 3c900 NIC troubles Hello folks ~ I'm trying to get my 3Com 3c900B-TPO working under Debian 2.2.18pre21. Here's what I've tried, and what I know, or think I know :P - Debian installer didn't detect the card. - The card's not detected by Debian at boot (I found no 'eth0' in dmesg) - 'ifconfig' lists only "lo" (local loopback?) - 'ifconfig eth0 up' gives me "eth0 not found" - but 'lspci' shows the card correctly as "02:09.0 Ethernet controller 3com 3c900B-TPO" - Plug 'n Pray is turned off in BIOS I tried to use linuxconf to set the 3c59x module, but that failed. It looks like it created an "/etc/conf.modules" file, which Debian tells me is deprecated. So no help there. Peripherally, is linuxconf a good thing to use on Debian? Frankly, I don't know any other way of doing it. Next, I downloaded 3Com's driver ("3c90x-1.0.0i.tar.gz" version 1.0.0i from http://support.3com.com/infodeli/tools/nic/linuxdownload.htm) and the install script says I have the wrong kernel version. So I tried to run the "compile_UP" script, as the readme suggests, and got PAGES of errors (further than I can scroll back up). Pointers deferencing and parsers not parsing all over the place. Two weeks ago I had a Red Hat 7 installation that detected the card right off and set it to use the 3c59x module. I don't know if it was the same version of that module that my Debian install now has. This is not a RH vs. Debian flame (I formatted the RH disk to install Debian, so you see where my preference lies), just an observation. I've done web and usenet searches, to no avail. One person's advice was to get a different NIC, which is silly. I called 3Com and they said, "Debian? I dated a girl named Debbie once." Once they realized I was talking about an OS they told me it was unsupported. And now I'm pretty much stuck. I'm rather new to all this. All the documents I've read recently make the process look pretty easy, once you've got the correct module. I've tried, without success, looking for a pre-compiled module, but I'm sure I don't know the best places to look. Any advice? Much appreciated. Randall P.S. I subscribe to the list, so you can reply there. -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED] -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
