Please fold likne in 72. Need to compile SCSI CDrom support. I think. Read CD-WRITING HOWTO for detail.
Osamu On Sun, Feb 11, 2001 at 07:20:49PM -0600, Bernard and Jennifer Cohen wrote: > > I have been having trouble getting my cdwriter to work using xcdroast. I got > it to the point of writing an audio cd when all it produced was 12 tracks of > noise and a new beer coaster. When looking at the ide/scsi devices recognized > by xcdroast the cdwriter is shown under both scsi and ide devices and the > regular cdrom is not recognized at all. I have enclosed a what I hope is a > all the relevant information as to set up. Would somebody also please provide > me with some sources on module set-up particularly the instructions > recognized by etc/modules.conf and how to connect all those char-major-xxx > with the modules, and what modules to add to etc/modules. > Thanks, > Bernie Cohen > > > > > from .config: > > CONFIG_BLK_DEV_FD=y > CONFIG_BLK_DEV_IDE=y > # CONFIG_BLK_DEV_HD_IDE is not set > CONFIG_BLK_DEV_IDEDISK=y > CONFIG_BLK_DEV_IDECD=m > # CONFIG_BLK_DEV_IDETAPE is not set > # CONFIG_BLK_DEV_IDEFLOPPY is not set > CONFIG_BLK_DEV_IDESCSI=m > > # SCSI support > # > CONFIG_SCSI=y > # CONFIG_BLK_DEV_SD is not set > # CONFIG_CHR_DEV_ST is not set > CONFIG_BLK_DEV_SR=y > CONFIG_BLK_DEV_SR_VENDOR=y > CONFIG_CHR_DEV_SG=y > # CONFIG_SCSI_MULTI_LUN is not set > CONFIG_SCSI_CONSTANTS=y > # CONFIG_SCSI_LOGGING is not set > > CONFIG_ISO9660_FS=y > CONFIG_JOLIET=y > > only line added to etc/modules.conf: > > options ide-cd ignore=hdc > > > proc/modules: > > ppp_deflate 39392 0 (autoclean) > bsd_comp 3880 0 (autoclean) > ide-scsi 7144 0 > ide-cd 22904 0 > cdrom 26524 0 [ide-cd] > sd_mod 15536 0 (unused) > joy-analog 4808 0 (unused) > joystick 5628 0 [joy-analog] > softoss2 56696 0 > awe_wave 156756 0 > opl3 10952 0 > sb 32948 0 > uart401 6128 0 [sb] > sound 56344 0 [softoss2 awe_wave opl3 sb uart401] > soundlow 416 0 [sound] > soundcore 2596 7 [sb sound] > > cdrecord -scanbus: > > Cdrecord 1.8 (i686-pc-linux-gnu) Copyright (C) 1995-2000 Jörg Schilling > Using libscg version 'schily-0.1' > scsibus0: > 0,0,0 0) 'YAMAHA ' 'CRW8824E ' '1.00' Removable CD-ROM > 0,1,0 1) * > 0,2,0 2) * > 0,3,0 3) * > 0,4,0 4) * > 0,5,0 5) * > 0,6,0 6) * > 0,7,0 7) * > > > edited from dmesg |more: > > VP_IDE: IDE controller on PCI bus 00 dev 39 > VP_IDE: not 100% native mode: will probe irqs later > ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:DMA, hdb:DMA > ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdc:DMA, hdd:DMA > hda: Maxtor 91366U4, ATA DISK drive > hdb: CD-ROM Drive/F5A, ATAPI CDROM drive > hdc: YAMAHA CRW8824E, ATAPI CDROM drive > ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 > ide1 at 0x170-0x177,0x376 on irq 15 > hda: Maxtor 91366U4, 13029MB w/2048kB Cache, CHS=1661/255/63, UDMA > Floppy drive(s): fd0 is 1.44M, fd1 is 1.44M > FDC 0 is a post-1991 82077 > scsi : 0 hosts. > scsi : detected total. > > hdb: ATAPI 48X CD-ROM drive, 128kB Cache > Uniform CD-ROM driver Revision: 3.11 > ide-cd: ignoring drive hdc > scsi0 : SCSI host adapter emulation for IDE ATAPI devices > scsi : 1 host. > Vendor: YAMAHA Model: CRW8824E Rev: 1.00 > Type: CD-ROM ANSI SCSI revision: 02 > Detected scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0 > sr0: scsi3-mmc drive: 24x/16x writer cd/rw xa/form2 cdda tray > Uniform CD-ROM driver Revision: 3.11 > > this is appended to 'dmesg |more' after xcdroast has been entered and then > closed: > > cdrom: open failed. > VFS: Disk change detected on device ide0(3,64) > cdrom: open failed. > VFS: Disk change detected on device ide0(3,64) > ide-scsi: hdc: unsupported command in request queue (0) > end_request: I/O error, dev 16:00 (hdc), sector 0 -- + Osamu Aoki <[EMAIL PROTECTED]>, GnuPG-key: 1024D/D5DE453D + + Fingerprint: 814E BD64 3288 40E7 E88E 3D92 C3F8 EA94 D5DE 453D + + === http://www.aokiconsulting.com ======= Cupertino, CA USA === +
