Hi all,
some machines are just plain unco-operative. After getting a custom
aic7870 rescu and drivers disks, I got installed and then faced this
set of messages on boot.
My apologies if it seems long but I am assuming that the root of
this oproblem lies with the scsi setup.
the cards claim to work but the command route add -net just causes
the shell to hang until Ctrl C is pressed. eth0 can be ping itself
but nothing else can ping it. eth1 cannot be ping because I can't
set up a route.
All help appreciated. Patrick Kirk
Memory: sized by int13 088h
Console: 16 point font, 400 scans
Console: colour VGA+ 80x25, 1 virtual console (max 63)
pcibios_init : BIOS32 Service Directory structure at 0x000f0280
pcibios_init : BIOS32 Service Directory entry at 0xf0210
pcibios_init : PCI BIOS revision 2.10 entry at 0xf0200
Probing PCI hardware.
Calibrating delay loop.. ok - 66.36 BogoMIPS
Memory: 62980k/65536k available (848k kernel code, 384k reserved, 1324k data)
Swansea University Computer Society NET3.035 for Linux 2.0
NET3: Unix domain sockets 0.13 for Linux NET3.035.
Swansea University Computer Society TCP/IP for NET3.034
IP Protocols: IGMP, ICMP, UDP, TCP
VFS: Diskquotas version dquot_5.6.0 initialized
Checking 386/387 coupling... Ok, fpu using exception 16 error reporting.
Checking 'hlt' instruction... Ok.
Intel Pentium with F0 0F bug - workaround enabled.
alias mapping IDT readonly ... ... done
Linux version 2.0.36 ([EMAIL PROTECTED]) (gcc version 2.7.2.3) #1 Mon Aug 23
21:08:31 CDT 1999
Starting kswapd v 1.4.2.2
Real Time Clock Driver v1.09
tpqic02: Runtime config, $Revision: 0.4.1.5 $, $Date: 1994/10/29 02:46:13 $
tpqic02: DMA buffers: 20 blocks, at address 0x219600 (0x2195bc)
Ramdisk driver initialized : 16 ramdisks of 4096K size
loop: registered device at major 7
hdb: 40X PCA403CD, ATAPI CDROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
md driver 0.36.3 MAX_MD_DEV=4, MAX_REAL=8
(scsi0) <Adaptec AIC-7870 SCSI host adapter> found at PCI 10/0
(scsi0) Wide Channel, SCSI ID=7, 16/255 SCBs
(scsi0) Downloading sequencer code... 406 instructions downloaded
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.19/3.2.4
<Adaptec AIC-7870 SCSI host adapter>
scsi : 1 host.
(scsi0:0:0:0) Synchronous at 20.0 Mbyte/sec, offset 8.
Vendor: SEAGATE Model: ST34572W Rev: 0876
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
scsi : detected 1 SCSI disk total.
SCSI device sda: hdwr sector= 512 bytes. Sectors= 8388316 [4095 MB] [4.1 GB]
Partition check:
sda: sda1 sda2 sda3 < sda5 sda6 sda7 sda8 sda9 sda10 >
VFS: Mounted root (ext2 filesystem) readonly.
Adding Swap: 102380k swap-space (priority -1)
Adding Swap: 102380k swap-space (priority -2)
ne2k-pci.c:v0.99L 2/7/98 D. Becker/P. Gortmaker
http://cesdis.gsfc.nasa.gov/linux/drivers/ne2k-pci.html
ne2k-pci.c: PCI NE2000 clone 'Via 82C926' at I/O 0xd080, IRQ 15.
eth0: PCI NE2000 found at 0xd080, IRQ 15, 08:00:39:01:04:66.
tulip.c:v0.89H 5/23/98 [EMAIL PROTECTED]
eth1: Digital DC21040 Tulip at 0xd000, 00 00 c0 a9 76 0f, IRQ 10.
Serial driver version 4.13 with no serial options enabled
tty00 at 0x03f8 (irq = 4) is a 16550A
tty01 at 0x02f8 (irq = 3) is a 16550A
Linux PCMCIA Card Services 3.0.14
kernel build: 2.0.36 unknown
options: [pci] [cardbus]
Intel PCIC probe: not found.
ds: no socket drivers loaded!
eth1: No 10baseT link beat found, switching to AUI media.
eth0: timeout waiting for Tx RDC.
eth0: timeout waiting for Tx RDC.
eth0: timeout waiting for Tx RDC.
eth0: timeout waiting for Tx RDC.
eth0: timeout waiting for Tx RDC.
