Ron Rademaker <[EMAIL PROTECTED]> writes:
> A few days ago I posted this:
>
> ========================================================================
> I've made it, from a windows pc I can call in to my linuxserver that uses
> ISDN but, there's a connection but theer's no communication. The type of
> connection on the windows side is SLIP and i've set the isdn encapsulation
> to rawip (I've also tried ip, ethernet and syncppp... no result.
> When I ping from number 1 to numbber 2 I see that bytes are send from one
> side, the other side receives the bytes, but down not answer.....
> Should I set the type of connection somewhere else in linux then on
> isdnctrl encap .............. ????
> Anybody knows how I can solve this.
>
> (I have the SLIP module in my kernel (compiled as a modules and insmodded
> the thin.).
>
> Ron
>
> =========================================================================
>
> Nobody answered... is this question really that difficult???
>
> Ron
Sorry, I don´t now about slip, but i have it working with syncppp.
Heres the Config:
/etc/isdn/device.ippp1:
-----------------------------------
#!/bin/sh
# Get the device name
set -e ; device=`basename $0`; device=${device#*.}
# DIALMODE:
DIALMODE=auto # XXX_
# Configuration (start)
case "$1" in
start)
# First you need to create the interface
isdnctrl addif ${device}
# eaz name num
isdnctrl eaz ${device} 9849198
# addphone name in num
# Set the phone number(s) that the IP-interface "name" is supposed to
# accept for incoming calls. If no num ber is given incoming calls are
# disabled. More than one number can be set by calling isdnctrl addphone
# repeatedly. Also wildcards can be used (see below).
isdnctrl addphone ${device} in "*"
# secure name on|off
isdnctrl secure ${device} off
# huptimeout name seconds
isdnctrl huptimeout ${device} 120
# ihup name on|off
# Turn on or off the hangup timeout for incoming calls on interface name
isdnctrl ihup ${device} on
# encap name encapname
# Set the encapsulation mode for interface "name". Possible modes for
# encapname are: rawip ip cisco_h ethernet syncppp uihdlc
# (most people use rawip, syncppp or cisco_h)
isdnctrl encap ${device} syncppp
# l2_prot name protocol
isdnctrl l2_prot ${device} hdlc
# l3_prot name protocol
isdnctrl l3_prot ${device} trans
# verbose num
isdnctrl verbose 2
# CHARGEHUP FUNCTION
# chargehup name on|off
isdnctrl chargehup ${device} on
# OTHER OPTIONS
# See also : isdnctrl(8), isdnctrl help text
# pppbind is not yet documented in that manpage :-(
isdnctrl pppbind ippp1 1
# NETWORK SETUP
ifconfig ${device} up
ifconfig ${device} 192.168.12.1 pointopoint 192.168.12.20
ifconfig ${device} -arp -broadcast
isdnctrl dialmode $device $DIALMODE || true
;;
# Delete the interface
stop)
isdnctrl dialmode $device off || true
# Commands to undo the network stuff
route del 192.168.12.20 2> /dev/null || true
ifconfig $device down 2> /dev/null || true
isdnctrl delif $device 2> /dev/null || true
;;
# the rest is generic, don't touch
*)
echo "Usage: $0 {start|stop}"
exit 1
;;
esac
exit 0
---------------------------eof
/etc/isdn/ipppd.ippp1
debug # enable debugging
lock # create a lock file for device
lcp-restart 1 # Set timeout for LCP
require-pap # allow only pap authetication
novj # van jacobsen compression on/off
nobsdcomp # bsd compression on/off
192.168.12.1:192.168.12.20 # set local ip to X, remote ip to Y
mtu 1500 # set maximum size of transmit units to X
ms-dns 192.168.12.1 # dns address for the peers use
ms-wins 192.168.12.1 # wins address for the peers use (I have Samba)
ms-wins 192.168.12.1 # wins address for the peers use
noipx # en/disable ipx
----------------------------------------------eof
Make shure to add users to pap-secrets and to allow access for the
client if using ipchains etc...
