I've just installed a SCSI host adapter "Mylex Flashpoint LW (BT-950)"
into my computer. Everything seemed ok until I realized that the
Ethernet card, 3COM 3c509, ISA, _not_ plug and play, has stopped
working. The network card is recognized by the kernel but no data goes
over it.
Here you have some excerpt from the boot messages:
scsi: ***** BusLogic SCSI Driver Version 2.1.15 of 17 August 1998 *****
scsi: Copyright 1995-1998 by Leonard N. Zubkoff <[EMAIL PROTECTED]>
scsi0: Configuring BusLogic Model BT-950 PCI Wide Ultra SCSI Host Adapter
scsi0: Firmware Version: 5.02, I/O Address: 0x6000, IRQ Channel: 11/Level
scsi0: PCI Bus: 0, Device: 15, Address: 0xE4000000, Host Adapter SCSI ID: 7
scsi0: Parity Checking: Enabled, Extended Translation: Enabled
scsi0: Synchronous Negotiation: Fast, Wide Negotiation: Enabled
scsi0: Disconnect/Reconnect: Enabled, Tagged Queuing: Enabled
scsi0: Driver Queue Depth: 255, Scatter/Gather Limit: 128 segments
scsi0: Tagged Queue Depth: Automatic, Untagged Queue Depth: 3
scsi0: Error Recovery Strategy: Default, SCSI Bus Reset: Enabled
scsi0: SCSI Bus Termination: Both Enabled, SCAM: Disabled
scsi0: *** BusLogic BT-950 Initialized Successfully ***
scsi0 : BusLogic BT-950
scsi : 1 host.
Vendor: SEAGATE Model: ST31230N Rev: 0510
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
scsi0: Target 0: Queue Depth 28, Synchronous at 10.0 MB/sec, offset 15
scsi : detected 1 SCSI disk total.
SCSI device sda: hdwr sector= 512 bytes. Sectors= 2069860 [1010 MB] [1.0 GB]
eth0: 3c509 at 0x300 tag 1, BNC port, address 00 a0 24 dd 39 11, IRQ 10.
3c509.c:1.12 6/4/97 [EMAIL PROTECTED]
I can't see any obvious IRQ od I/O conflict:
[EMAIL PROTECTED]:/proc # cat interrupts
CPU0
0: 320416 XT-PIC timer
1: 4486 XT-PIC keyboard
2: 0 XT-PIC cascade
3: 7673 XT-PIC serial
4: 1678 XT-PIC serial
8: 0 XT-PIC rtc
10: 0 XT-PIC 3c509
11: 144 XT-PIC BusLogic BT-950
12: 25284 XT-PIC PS/2 Mouse
13: 1 XT-PIC fpu
14: 10354 XT-PIC ide0
15: 7 XT-PIC ide1
NMI: 0
[EMAIL PROTECTED]:/proc # cat ioports
0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0070-007f : rtc
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
02f8-02ff : serial(set)
0300-030f : 3c509
0376-0376 : ide1
03c0-03df : vga+
03f6-03f6 : ide0
03f8-03ff : serial(auto)
6000-60ff : BusLogic BT-950
9000-9007 : ide0
9008-900f : ide1
What else should I look at?
Do you know of any possible incompatibility between the two ?
--
-------------------------------------------------------------------------------
Pierfrancesco Caci | mailto:[EMAIL PROTECTED] - http://gusp.infogroup.it
ik5pvx | http://www.geocities.com/SoHo/Lofts/8999
Firenze - Italia | Office for the Complication of Otherwise Simple Affairs
Linux penny 2.1.131 #1 Fri Dec 4 23:22:32 CET 1998 i586 unknown
