Patrick Ouellette wrote: > Does you SCSI card have *gasp* jumpers to configure the interrupts
Jumpers for both interrupts and IO adress...I had (previously to posting my first message even) check /proc/interrupts found that 11 and 9 are free interrupts for me...and the board suports both (it also suports 12 which is my PS/2 mouse and 10 which is my NIC card) I don't have the manual for the card but... if I look at the board itself i see jumpers (yes jumpers...I LOVE jumpers.. the best way to set IRQs and what not) next to one of the sets of jumpers there are a few rows marked I9, I10, I11,I12. ...I assume these ar eteh interrupt setting then there is another which is marked in: 140 out: 340 (I think...I forget the higher value) in any case yes...I am pretty darned sure I used the rigth IRQ > (or software)? I get similar messages if I put the wrong irq in > the AHA152x module load line. hmm well it isn't a module load line... its in the kernel boot parametersI don't use kernel modules whenever I can avoid them...I just compile it into the kernel and turn off what I don't need same diff tho I guess.... > If it is one of those plug-n-pray > cards there used to be some utils that might help, iirc. > > Pat Ouellette > > Email: [EMAIL PROTECTED] > Amateur Radio (voice): KB8PYM on KB8YVY repeater (52.650 / 146.835 / > 444.650) > Amateur Radio (packet): [EMAIL PROTECTED] > Running down the hall: Hey you! > > You can ping your node, you can ping you neighbor, but you can't ping your > neighbors node. > > > -----Original Message----- > > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of > > Stephen Carpenter > > Sent: Wednesday, April 29, 1998 9:37 PM > > To: debian-user list > > Subject: ACK! SCSI Not WOrking > > > > > > -----BEGIN PGP SIGNED MESSAGE----- > > > > I got my SCSI tape drive and I installed a SCSI card I had lying around > > unfortunatly it didn't work :( > > I THINK the problem may be the controller... > > I get the messages: > > aha152x: processing commandline: ok > > aha152x: BIOS test: passed, detected 1 controller(s) > > aha152x0: vital data: PORTBASE=0x140, IRQ=9, SCSI ID=7, reconnect=enabled, > > parity=enabled, synchronous=disabled, delay=100, extended > > translation=disabled > > aha152x: trying software interrupt, lost. > > aha152x: IRQ 9 possibly wrong. Please verify. > > - --- > > I have tried IRQ 11 with the same effect...then it is... > > scsi0 : Adaptec 152x SCSI driver; $Revision: 1.18 $ > > scsi : 1 host. > > scsi : aborting command due to timeout : pid 0, scsi0, channel 0, id 0, > > lun 0 Test Unit Ready 00 00 00 00 00 > > - --- repeated for id 0 - 6 > > The SCSI card is from a ZIP SCSI drive (I got it for free from omeone > > who already had a SCSI card and installed a ZIP) > > It calls itself (written on the board) an > > Adaptec AVA-1502 > > the Tape drive apears to be (jumpers) SCSI ID 4, Parity on, Termination > > power on > > Any ideas? should I just forget it asnd buy a new adapter? > > I recompiled my kernel...turned on SCSI supoert and > > all of the Adaptec Drivers ...I am running Kernel 2.0.29 > > (on a hamm system but I doubt that matters) > > I read the SCSI-HOWTO...but it was of no help :( > > - -Steve > > > > > > -----BEGIN PGP SIGNATURE----- > > Version: 2.6.3a > > Charset: noconv > > > > iQCVAwUBNUfVwnxvn0zebBV9AQGVBAQAhe8UovDSlOKNS6ZPVWw+Ux4EHcRqfJm8 > > qeGY7+dzJmQM8eHdW+In0kGwpKxVbzmefIJT0tSXsXT1tQHJzKlwl9SzEWcGwFzV > > ZMI6xA4Zj3AfcUskCNkPNWXfOxyw8ouFxBKOaVyePaGjwc7sk+Fboks+e5ivLhSX > > ObyL+LUidvo= > > =ri2i > > -----END PGP SIGNATURE----- > > > > > > -- > > To UNSUBSCRIBE, email to [EMAIL PROTECTED] > > with a subject of "unsubscribe". Trouble? Contact > > [EMAIL PROTECTED] > > > > -- -----BEGIN PGP PUBLIC KEY BLOCK----- Version: 2.6.3a mQCNAzG30VYAAAEEAK8aj0pclro6ULfzim7TN0Y2FeNtzJKkA9rNZ8KGim3N+ULO 1dn4tfIqymSNDQLc/SDCvliTDP9vodSSYfQaovHE2wWE6n5igGIhA3RqyAnX9ctl 4wPI5FYJHHhsl2OsKJLui1TbTo6uJul3vG4U9CnopYscEbHm+Hxvn0zebBV9AAUR tCVTdGVwaGVuIEouIENhcnBlbnRlciA8U0pDQGRlbHBoaS5jb20+iQCVAwUQMcz2 fnxvn0zebBV9AQFb2QP+OiFDvDvuuomwdZns+pQTVqOu5zy3wdlyQki4Mo/X+5qY Nmj0s4qjfowaimj69db6w6jSvzeEY5gnlM92NI5dj6qliJScBVlRNBRffsHkvHkk C27LjUtVYkF3j30wyCwdzNe0FhRYBsz5F+i78ZSPrxlUkOvfFBUgAo2ZFwlwS4k= =z4IB -----END PGP PUBLIC KEY BLOCK----- -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
