Thanks for the suggestion, but thats not the problem. I should make it
clear that X worked perfectly fine before the upgrade. I have a pretty
much stock Debian system also.
Someone also suggested that I do a:
X -probeonly >out 2>&1
Its a good idea, but it doesn't show any errors that I can see. I've
appended the output to the end of this message if anyone would like to
take a look.
I do notice that it says "Operating System: Linux 2.0.21 i486 [ELF]", but
I'm using 2.0.27...maybe thats the system it was compiled on?
On Tue, 8 Jul 1997, Igor Grobman wrote:
> I had a similar problem. The reason was a corrupted ~/.Xauthority file. Try
> deleting it, and relogging on. That fixed it for me.
>
> HTH
[cut]
XFree86 Version 3.3 / X Window System
(protocol Version 11, revision 0, vendor release 6300)
Release Date: Jun 2 1997
If the server is older than 6-12 months, or if your card is newer
than the above date, look for a newer version before reporting
problems. (see http://www.XFree86.Org/FAQ)
Operating System: Linux 2.0.21 i486 [ELF]
Configured drivers:
S3: accelerated server for S3 graphics adaptors (Patchlevel 0)
newmmio, mmio_928, s3_generic
(using VT number 7)
XF86Config: /etc/X11/XF86Config
(**) stands for supplied, (--) stands for probed/default values
(**) XKB: rules: "xfree86"
(**) XKB: model: "pc102"
(**) XKB: layout: "us"
(**) Mouse: type: MouseSystems, device: /dev/mouse, baudrate: 1200
(**) S3: Graphics device ID: "Primary Card"
(**) S3: Monitor ID: "Primary Monitor"
(**) FontPath set to
"/usr/X11R6/lib/X11/fonts/misc:unscaled,/usr/X11R6/lib/X11/fonts/75dpi:unscaled,/usr/X11R6/lib/X11/fonts/100dpi:unscaled,/usr/X11R6/lib/X11/fonts/Type1,/usr/X11R6/lib/X11/fonts/Speedo,/usr/X11R6/lib/X11/fonts/misc,/usr/X11R6/lib/X11/f
onts/75dpi,/usr/X11R6/lib/X11/fonts/100dpi"
(--) S3: chipset: 968 rev. 3
(--) S3: chipset driver: newmmio
(--) S3: card type: 386/486 localbus
(--) S3: videoram: 4096k
(--) S3: Detected an IBM RGB524 ramdac rev. e0
(--) S3: Ramdac type: ibm_rgb524
(**) S3: Ramdac speed: 220 MHz
(--) S3: Using hardware cursor from IBM RGB52x RAMDAC
(--) S3: #9 Motion 771 BIOS found
(--) S3: Using IBM RGB52x programmable clock (MCLK 60.000 MHz)
(**) S3: with refclock 16.000 MHz (probed 16.112 & 15.956)
(--) S3: Maximum allowed dot-clock: 220.000 MHz
(**) S3: Mode "1024x768": mode clock = 65.000
(**) S3: Mode "800x600": mode clock = 50.000
(**) S3: Mode "640x480": mode clock = 31.500
(--) S3: Operating RAMDAC in pixel multiplex mode
(--) S3: Using 8 bits per RGB value
(--) S3: Virtual resolution set to 1024x768
--
TO UNSUBSCRIBE FROM THIS MAILING LIST: e-mail the word "unsubscribe" to
[EMAIL PROTECTED] .
Trouble? e-mail to [EMAIL PROTECTED] .
