Hi List,
still got problems mounting and accessing an external HD (MacPower
Icecube FW800) through USB. Note that this is on a Powerpc, but it might
not be a platform specific problem, hence the post.
I am here on Debian Testing with an 2.6.11.5 kernel.
I think i got all required modules loaded:
vfat 13888 0
msdos 8928 0
usb_storage 36512 0
ntfs 130256 0
fat 43772 2 vfat,msdos
sd_mod 16400 0
ohci1394 38404 0
evdev 9984 0
ohci_hcd 24648 0
uhci_hcd 42128 0
ehci_hcd 34952 0
sbp2 26064 0
scsi_mod 101308 3 usb_storage,sd_mod,sbp2
ieee1394 115688 2 ohci1394,sbp2
udf 94020 0
binfmt_misc 11656 0
usbhid 41536 0
usbcore 131024 6
usb_storage,ohci_hcd,uhci_hcd,ehci_hcd,usbhid
At power on, the HD gets listed in /proc/partitions:
8 0 195360984 sda
8 1 32764536 sda1 -> FAT32
8 2 32764567 sda2 -> FAT32
8 3 32764567 sda3 -> FAT32
8 4 97064730 sda4 -> ntfs
The partitions were made on a win2k box.
/var/log/messages shows the device:
Jun 12 17:59:12 gonzo kernel: usb 2-1: new full speed USB device using
ohci_hcd and address 38
Jun 12 17:59:12 gonzo kernel: scsi10 : SCSI emulation for USB Mass
Storage devices
Jun 12 17:59:13 gonzo usb.agent[19676]: usb-storage: already loaded
Jun 12 17:59:17 gonzo kernel: Vendor: SAMSUNG Model: SP2014N
Rev: VC10
Jun 12 17:59:17 gonzo kernel: Type: Direct-Access ANSI SCSI
revision: 04
Jun 12 17:59:17 gonzo kernel: SCSI device sda: 390721968 512-byte hdwr
sectors (200050 MB)
Jun 12 17:59:17 gonzo kernel: SCSI device sda: 390721968 512-byte hdwr
sectors (200050 MB)
Jun 12 17:59:18 gonzo kernel: /dev/scsi/host10/bus0/target0/lun0: p1
p2 p3 p4
Jun 12 17:59:18 gonzo kernel: Attached scsi disk sda at scsi10,
channel 0, id 0, lun 0
Jun 12 17:59:18 gonzo scsi.agent[19712]: sd_mod: loaded
sucessfully (for disk)
As i try to mount the first partition:
gonzo:~# mount -v -t msdos /dev/sda1 /fw/
mount: /dev/sda1 is not a valid block device
And /var/log/messages gives:
Jun 12 18:00:24 gonzo kernel: usb 2-1: reset full speed USB device
using ohci_hcd and address 38
Jun 12 18:00:25 gonzo kernel: usb 2-1: scsi_eh_10 timed out on ep0in
Jun 12 18:00:30 gonzo kernel: usb 2-1: scsi_eh_10 timed out on ep0in
Jun 12 18:00:30 gonzo kernel: usb 2-1: reset full speed USB device
using ohci_hcd and address 38
Jun 12 18:00:31 gonzo kernel: usb 2-1: scsi_eh_10 timed out on ep0in
Jun 12 18:00:36 gonzo kernel: usb 2-1: scsi_eh_10 timed out on ep0in
Jun 12 18:00:37 gonzo kernel: scsi: Device offlined - not ready after
error recovery: host 10 channel 0 id 0 lun 0
Jun 12 18:00:37 gonzo kernel: usb 2-1: USB disconnect, address 38
The same is with the other partitions (fat and ntfs(readonly))...
I am stuck here...
A little surfing got me the info to disable CONFIG_EFI_PARTION in the
kernel conf, but it was always off...
Any ideas what to try next would be very appreciated!
regards,
Peter P.
(Please CC me as i read this list in digest-mode)
--
To UNSUBSCRIBE, email to [EMAIL PROTECTED]
with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
