On Sun, 06 Jun 2004 15:54:04 -0400
Adam Aube <[EMAIL PROTECTED]> wrote:
>messmate wrote:
>
>> i've setted-up an old p100 box as a debian router (only router)
>> At boot, when reached 'Configuring interfaces ...' i've this error:
>> 'Configuring network interfaces:eth1: linkup bla bla bla ..'
>> and a 'failed'. Eth1 is connected to my dsl-modem.
>
>What does the output of "ifconfig eth1" show?
>
>What happens if you run "ifup eth1" manually as root?
>
>Adam
>
Well see here my ifconfig :
eth0 Link encap:Ethernet HWaddr 00:80:C8:EC:92:B5
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:9311 errors:0 dropped:0 overruns:0 frame:0
TX packets:11379 errors:0 dropped:0 overruns:0 carrier:0
collisions:28 txqueuelen:1000
RX bytes:780075 (761.7 KiB) TX bytes:8806177 (8.3 MiB)
Interrupt:10 Base address:0xf880
eth1 Link encap:Ethernet HWaddr 00:E0:29:3C:34:BD
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:24114 errors:0 dropped:0 overruns:0 frame:0
TX packets:22005 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:9788053 (9.3 MiB) TX bytes:1646873 (1.5 MiB)
Interrupt:11 Base address:0xec00
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:20 errors:0 dropped:0 overruns:0 frame:0
TX packets:20 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1576 (1.5 KiB) TX bytes:1576 (1.5 KiB)
ppp0 Link encap:Point-to-Point Protocol
inet addr:82.255.103.37 P-t-P:192.168.254.254
Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST
MTU:1492 Metric:1 RX packets:23234 errors:0 dropped:0
overruns:0 frame:0 TX packets:21113 errors:0 dropped:0
overruns:0 carrier:0 collisions:0 txqueuelen:3
RX bytes:9222851 (8.7 MiB) TX bytes:1124242 (1.0 MiB)
and my route :
ip route
192.168.254.254 dev ppp0 proto kernel scope link src 82.255.103.37
192.168.1.0/24 dev eth0 proto kernel scope link src 192.168.1.1
default via 192.168.254.254 dev ppp0
More clearly:
at boot, the network configuring script invokes TWICe eth1 followed
by a 'failed'.
But eth1 is up !
I don't understand what happen exactly about that.
A second pb is that ipmasq must be launched manually after a
root login. A link S99ipmasq to rc2.d for example has no effect.
This are parts of dmesg:
eth0: MII PHY found at address 8, status 0x782d advertising 05e1 Link
0000 eth1: Identified 8139 chip type 'RTL-8139A'
eth1: link up, 100Mbps, half-duplex, lpa 0x40A1
eth1: link up, 100Mbps, half-duplex, lpa 0x40A1
And what i've found in syslog:
Jun 6 10:50:43 router pppd[350]: Cannot determine ethernet address for
proxy ARP
Any help would be very appreciated.
mess-mate
--
To UNSUBSCRIBE, email to [EMAIL PROTECTED]
with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
