Hola de nuevo:
escribi con el siguiente problema (mensajes de dmesg):
------------------------------------------------------------
> > Uniform Multi-Platform E-IDE driver Revision: 6.31
> > ide: Assuming 33MHz system bus speed for PIO modes;
> > override with idebus=xx
> > VP_IDE: IDE controller on PCI bus 00 dev 39
> > VP_IDE: detected chipset, but driver not compiled in!
> > VP_IDE: chipset revision 16
> > VP_IDE: not 100% native mode: will probe irqs later
> > ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hda:DMA,
> > hdb:DMA ide1: BM-DMA at 0xd008-0xd00f, BIOS settings:
> > hdc:DMA, hdd:DMA
------------------------------------------------------------
como bien me recomendaron estaba sin compilar el nucleo sin
el chipset vt82xxxx, tras hacerlo me salia un mensaje parecido
a este
------------------------------------------------------------
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override
with idebus=xx VP_IDE: IDE controller on PCI bus 00 dev 39
VP_IDE: chipset revision 16
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override
with idebus=xx
VP_IDE: VIA vt82c596b (rev 23) IDE UDMA66 <<<<<<<<
controller on pci00:07.1 ide0: BM-DMA at
0xd000-0xd007, BIOS settings: hda:DMA, hdb:DMA ide1: BM-DMA
at 0xd008-0xd00f, BIOS settings: hdc:DMA, hdd:DMA hda:
C/H/S=29437/16/255 from BIOS ignored hda: Maxtor 6Y060L0, ATA
DISK drive hdb: LG CD-ROM CRD-8522B, ATAPI CD/DVD-ROM drive
hdc: ST320413A, ATA DISK drive
hdd: 24X10, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
blk: queue c0362544, I/O limit 4095Mb (mask 0xffffffff)
hda: 120103200 sectors (61493 MB) w/2048KiB Cache,
CHS=119150/16/63, UDMA(66) <<<<<<<<<<<<<<<<<<<<<<<<
blk: queue c0362888, I/O limit 4095Mb (mask 0xffffffff)
hdc: setmax LBA 39102337, native 39102336
hdc: 39102336 sectors (20020 MB) w/1024KiB Cache,
CHS=38792/16/63, UDMA(66) <<<<<<<<<<<<<<<<<<<<<<<<<
hdb: ATAPI 48X CD-ROM drive, 128kB Cache, DMA
------------------------------------------------------------
mirando las partes seņaladas (con <<<<<<<<<<<<) parece q estan
funcionando a 66Mhz, aunque al principio siga poniendo ide:
Assuming 33Mhz...
Tras esto lo que hice es pasarle al nucleo con el lilo el
parametro idebus=66, y obtenia lo mismo, pero un comentario
como q no podia ponerlo, y comantandome que si tenia un bus
de 80 hilos pusiera ide0=ata66, lo puse y obtengo lo
siguiente:
------------------------------------------------------------
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override
with idebus=xx VP_IDE: IDE controller on PCI bus 00 dev 39
VP_IDE: chipset revision 16
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c596b (rev 23) IDE UDMA66 controller on
pci00:07.1
VP_IDE: ATA-66/100 forced bit set (WARNING)!! <<<<<<<<<<<<<<
ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hda:DMA,
hdb:DMA ide1: BM-DMA at 0xd008-0xd00f, BIOS settings:
hdc:DMA, hdd:DMA hda: C/H/S=29437/16/255 from BIOS ignored
hda: Maxtor 6Y060L0, ATA DISK drive
hdb: LG CD-ROM CRD-8522B, ATAPI CD/DVD-ROM drive
hdc: ST320413A, ATA DISK drive
hdd: 24X10, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
blk: queue c0362544, I/O limit 4095Mb (mask 0xffffffff)
hda: 120103200 sectors (61493 MB) w/2048KiB Cache,
CHS=119150/16/63, UDMA(66)
blk: queue c0362888, I/O limit 4095Mb (mask 0xffffffff)
hdc: setmax LBA 39102337, native
39102336 hdc: 39102336 sectors (20020 MB) w/1024KiB Cache,
CHS=38792/16/63, UDMA(66)
hdb: ATAPI 48X CD-ROM drive, 128kB Cache, DMA
------------------------------------------------------------
Pero no me gusta nada la parte seņalada (con <<<<<<<<<<)
que me decis?? si lo dejo sin pasar ningun parametro me
funcionan los hd a 66Mhz?? parece q si no?
por ahora lo voy a dejar sin el parametro...
Gracias y hasta luego!
