Hola:
Los reyes me han traido un reproductor mp3, pero no consigo montarlo en mi
Linux.
Tengo un pen-drive que lo monto sin problemas.
Estos son los pasos que sigo para intentar montarlo:
#cat /proc/scsi/scsi
Attached devices:
Host: scsi2 Channel: 00 Id: 00 Lun: 00
Vendor: Generic Model: STORAGE DEVICE Rev: 0128
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi2 Channel: 00 Id: 00 Lun: 01
Vendor: Generic Model: STORAGE DEVICE Rev: 0128
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi2 Channel: 00 Id: 00 Lun: 02
Vendor: Generic Model: STORAGE DEVICE Rev: 0128
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi2 Channel: 00 Id: 00 Lun: 03
Vendor: Generic Model: STORAGE DEVICE Rev: 0128
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi4 Channel: 00 Id: 00 Lun: 00
Vendor: USB2.0 Model: (FS) FLASH DISK Rev: 1.00
Type: Direct-Access ANSI SCSI revision: 02
(El último es el reproductor, lo otro es un lector de memorias que se conecta
por USB que no da problemas)
#cdrecord -scanbus
Linux sg driver version: 3.5.31
Using libscg version 'schily-0.8'.
scsibus2:
2,0,0 200) 'Generic ' 'STORAGE DEVICE ' '0128' Removable Disk
2,1,0 201) *
2,2,0 202) *
2,3,0 203) *
2,4,0 204) *
2,5,0 205) *
2,6,0 206) *
2,7,0 207) *
scsibus4:
4,0,0 400) 'USB2.0 ' '(FS) FLASH DISK ' '1.00' Removable Disk
4,1,0 401) *
4,2,0 402) *
4,3,0 403) *
4,4,0 404) *
4,5,0 405) *
4,6,0 406) *
4,7,0 407) *
#sg_scan -i
/dev/sg0: scsi2 channel=0 id=0 lun=0 [em]
Generic STORAGE DEVICE 0128 [rmb=1 cmdq=0 pqual=0 pdev=0x0]
/dev/sg1: scsi2 channel=0 id=0 lun=1 [em]
Generic STORAGE DEVICE 0128 [rmb=1 cmdq=0 pqual=0 pdev=0x0]
/dev/sg2: scsi2 channel=0 id=0 lun=2 [em]
Generic STORAGE DEVICE 0128 [rmb=1 cmdq=0 pqual=0 pdev=0x0]
/dev/sg3: scsi2 channel=0 id=0 lun=3 [em]
Generic STORAGE DEVICE 0128 [rmb=1 cmdq=0 pqual=0 pdev=0x0]
/dev/sg4: scsi4 channel=0 id=0 lun=0 [em]
USB2.0 (FS) FLASH DISK 1.00 [rmb=1 cmdq=0 pqual=0 pdev=0x0]
(Con esto averiguo que esta en /dev/sg4)
#sg_map
/dev/sg0 /dev/sda
/dev/sg1 /dev/sdb
/dev/sg2 /dev/sdc
/dev/sg3 /dev/sdd
/dev/sg4 /dev/sde
(y con esto la "verdadera" direccion,/dev/sde)
#fdisk /dev/sde
Command (m for help): p
Disk /dev/sde: 522 MB, 522043904 bytes
17 heads, 59 sectors/track, 1016 cylinders
Units = cylinders of 1003 * 512 = 513536 bytes
This doesn't look like a partition table
Probably you selected the wrong device.
Device Boot Start End Blocks Id System
/dev/sde1 ? 775809 1913904 570754815+ 72 Unknown
Partition 1 has different physical/logical beginnings (non-Linux?):
phys=(357, 116, 40) logical=(775808, 8, 13)
Partition 1 has different physical/logical endings:
phys=(357, 32, 45) logical=(1913903, 14, 4)
Partition 1 does not end on cylinder boundary.
/dev/sde2 ? 168185 2098423 968014120 65 Novell Netware 386
Partition 2 has different physical/logical beginnings (non-Linux?):
phys=(288, 115, 43) logical=(168184, 16, 27)
Partition 2 has different physical/logical endings:
phys=(367, 114, 50) logical=(2098422, 8, 24)
Partition 2 does not end on cylinder boundary.
/dev/sde3 ? 1864289 3794527 968014096 79 Unknown
Partition 3 has different physical/logical beginnings (non-Linux?):
phys=(366, 32, 33) logical=(1864288, 10, 12)
Partition 3 has different physical/logical endings:
phys=(357, 32, 43) logical=(3794526, 1, 20)
Partition 3 does not end on cylinder boundary.
/dev/sde4 ? 1 3626348 1818613248 d Unknown
Partition 4 has different physical/logical beginnings (non-Linux?):
phys=(372, 97, 50) logical=(0, 0, 1)
Partition 4 has different physical/logical endings:
phys=(0, 10, 0) logical=(3626347, 7, 42)
Partition 4 does not end on cylinder boundary.
Partition table entries are not in disk order
(Ahora he elegido p en el fdisk para que me muestre las particiones, pero
intentando montar cada una de ellas me da error, no me deja montarlas)
#mount -t vfat /dev/sde1 /mnt/mp3
mount: /dev/sde1 is not a valid block device
Eso es lo que me dice cuando intento montar cada particion.
¿Alguna idea?
--
TiNePaS
http://www.agali.org
Asociación de Gaditanos Linuxeros
