VOcê está usando emulaçao-scsi?! Miguel D.
On Wed, 01 Dec 2004 12:57:05 -0200 Helder Pereira Cristo <[EMAIL PROTECTED]> wrote: > Como foi pedido por alguns estou incluindo o log gerado pelo xcdroast. > Será que agora é possível encontrar o erro? > desde já obrigado. > > > Calling: /usr/lib/xcdroast/bin/xcdrwrap CDRECORD dev= "ATAPI:0,0,0" > gracetime=2 fs=4096k -v driveropts=burnfree speed=32 -dao -eject -pad > -waiti tsize=220045s - > > scsidev: 'ATAPI:0,0,0' > devname: 'ATAPI' > scsibus: 0 target: 0 lun: 0 > Warning: Using ATA Packet interface. > Warning: The related Linux kernel interface code seems to be unmaintained. > Warning: There is absolutely NO DMA, operations thus are slow. > SCSI buffer size: 64512 > Cdrecord-Clone 2.01a34 (i686-pc-linux-gnu) Copyright (C) 1995-2004 Jörg > Schilling > NOTE: this version of cdrecord is an inofficial (modified) release of > cdrecord > and thus may have bugs that are not present in the original version. > Please send bug reports and support requests to > <[EMAIL PROTECTED]>. > The original author should not be bothered with problems of this version. > > TOC Type: 1 = CD-ROM > Waiting for data on stdin... > Using libscg version 'schily-0.8'. > Driveropts: 'burnfree' > atapi: 1 > Device type : Removable CD-ROM > Version : 0 > Response Format: 2 > Capabilities : > Vendor_info : 'HL-DT-ST' > Identifikation : 'CD-RW GCE-8320B ' > Revision : '1.04' > Device seems to be: Generic mmc CD-RW. > Current: 0x000A > Profile: 0x000A (current) > Profile: 0x0009 > Profile: 0x0008 > Profile: 0x0002 (current) > Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr). > Driver flags : MMC-2 SWABAUDIO BURNFREE > Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R > Drive buf size : 1968736 = 1922 KB > FIFO size : 4194304 = 4096 KB > Track 01: data 429 MB padsize: 30 KB > Total size: 493 MB (48:54.13) = 220060 sectors > Lout start: 493 MB (48:56/10) = 220060 sectors > Current Secsize: 2048 > ATIP info from disk: > Indicated writing power: 3 > Reference speed: 6 > Is not unrestricted > Is erasable > Disk sub type: High speed Rewritable (CAV) media (1) > ATIP start of lead in: -11596 (97:27/29) > ATIP start of lead out: 359849 (79:59/74) > 1T speed low: 4 1T speed high: 10 > 2T speed low: 4 2T speed high: 0 (reserved val 8) > power mult factor: 2 5 > recommended erase/write power: 4 > A1 values: 24 2A C8 > A2 values: 28 84 48 > Disk type: Phase change > Manuf. index: 20 > Manufacturer: Princo Corporation > Blocks total: 359849 Blocks current: 359849 Blocks remaining: 139789 > Starting to write CD/DVD at speed 10 in real SAO mode for single session. > Waiting for reader process to fill input buffer ... > input buffer ready. > BURN-Free is OFF. > Turning BURN-Free on > Performing OPC... > Sending CUE sheet... > cdrecord: WARNING: Drive returns wrong startsec (0) using -150 > Writing pregap for track 1 at -150 > Starting new track at sector: 0 > cdrecord: Input/output error. write_g1: scsi sendcmd: no error > CDB: 2A 00 00 00 02 6C 00 00 1F 00 > status: 0x0 (GOOD STATUS) > cmd finished after 10.056s timeout 200s > cdrecord: A write error occured. > cdrecord: Please properly read the error message above. > > write track data: error after 1269760 bytes > Writing time: 26.115s > Average write speed 181.0x. > Fixating... > Fixating time: 0.001s > BURN-Free was never needed. > cdrecord: fifo had 84 puts and 21 gets. > cdrecord: fifo was 0 times empty and 2 times full, min fill was 78%. > > > Jupercio Juliano wrote: > > > Helder Pereira Cristo wrote: > > > >> Tentei gravar em cd's regraváveis em mais de um programa (k3b e > >> XcdRoast) e nos dois encontrei problemas. A gravação é interrompida > >> logo no início. As mensagens de erro não esclarecem muita coisa. > >> > >> Com cd's graváveis não tenho problemas. > >> > >> Alguém poderia dar uma idéia por onde posso começar? > >> > > > > Bom, desisti de gravar cds regraváveis em formato udf ou outro FS > > que possa ser entendido como mídia gravável ao se colocar no drive de > > cd, para fazer tarefas de arrastar e soltar por exemplo. > > Vejo que há incompatibilidade entre os software, pelo menos no > > mundo proprietário, se gravo udf no nero, o easy cd creatror não > > reconhece e vice-versa. > > Faço o quê então, gravo com iso9660, assim abro em qualquer micro. > > Sugiro o mesmo. > > Mas um palpite sobre o seu cdrw, será que o k3b/xcd não estão > > pedindo pelo sistema de arquivos udf e com suporte a escrita? > > Talvez os módulos não tenham sido carregados. > > Como disseram, mande as mensagens de erro. > > > > abraços. > > > > -- > To UNSUBSCRIBE, email to [EMAIL PROTECTED] > with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED] > >
