Caro Orlando, Compile o kernel, e procure na sessão "Generic SCSI", ou algo parecido, por "tape" torne-o bult-in, faça isso também com as opções SCSI genéricas.
Já configurei servidores com Linux com DAT, DLT e sempre funcionou desta forma. Boa sorte ! -----Original Message----- From: Orlando Tempobono [mailto:[EMAIL PROTECTED] Sent: Tuesday, February 04, 2003 8:57 AM To: debian-user-portuguese@lists.debian.org Subject: Debian num servidor Compaq ML370 problemas com DAT Olá Pessoal, Instalei um Debian Woody com o bf2.4 num servidor Compaq Proliant ML370 Dual PIII 700 e foi tudo beleza, ele reconheceu o hardware de array de discos tranquilamente, logo em seguida usei um apt-get install kernel-image-2.4.18-686-smp e ele instalou o kernel correspondente para que fosse feito o reconhecimento dos 2 processadores, mais uma vez correu tudo bem. O problema está no reconhecimento da DAT SCSI, já "modprobei"(argh :)!!) o st.o , scsi_mod.o o scsi_log.o instalei o mt-st e: - quando executo: mt -f /dev/st0 status #que deveria mostrar o status do dispositivo de fita, correto? - ele retorna a msg.: /dev/st0: No such device Demais comandos como tar cvf /dev/st0 /home Alguem tem alguma dica ou experiência para compartilhar? ou sabe onde estou errando? Resolveria se eu compilasse o kernel com tais módulos embutidos no próprio ao invés de módulos? Toda ajuda é bem vinda pois já tentei um monte de coisas. Obrigado e até +, Orlando Tempobono - WMaster Mk [EMAIL PROTECTED] icq:40367870 Abaixo seguem mais detalhes que podem ajudar no raciocínio, sempre me disseram para postar as msgs na lista com objetividade e o maior número de detalhes possível, por favor me digam se o que estou fazendo ao postar toda a informação é correto. estaterlx:~# lsmod Module Size Used by Not tainted st 26548 0 (unused) af_packet 12936 1 (autoclean) scsi_debug 8800 0 (unused) scsi_mod 87320 2 [st scsi_debug] eepro100 17616 1 rtc 6104 0 (autoclean) ext3 58848 1 (autoclean) jbd 38056 1 (autoclean) [ext3] cpqarray 16576 2 (autoclean) unix 15236 75 (autoclean) estaterlx:~# cat /proc/interrupts CPU0 CPU1 0: 36985 47064 IO-APIC-edge timer 1: 1 5 IO-APIC-edge keyboard 2: 0 0 XT-PIC cascade 8: 2 1 IO-APIC-edge rtc 12: 40 75 IO-APIC-edge PS/2 Mouse 17: 653 650 IO-APIC-level eth0 19: 3274 3276 IO-APIC-level ida0 NMI: 0 0 LOC: 83964 83964 ERR: 0 MIS: 0 estaterlx:~# cat /proc/pci PCI devices found: Bus 0, device 0, function 0: Host bridge: ServerWorks CNB20LE Host Bridge (rev 5). Master Capable. Latency=64. Bus 0, device 0, function 1: Host bridge: ServerWorks CNB20LE Host Bridge (#2) (rev 5). Master Capable. Latency=64. Bus 0, device 1, function 0: RAID bus controller: PCI device 1000:0010 (LSI Logic / Symbios Logic (formerly NCR)) (rev 2). IRQ 19. Master Capable. Latency=192. Min Gnt=30.Max Lat=8. I/O at 0x2000 [0x20ff]. Non-prefetchable 32 bit memory at 0xc6000000 [0xc6ffffff]. Non-prefetchable 32 bit memory at 0xc5000000 [0xc5ffffff]. Bus 0, device 2, function 0: Ethernet controller: Intel Corp. 82557 [Ethernet Pro 100] (rev 8). IRQ 17. Master Capable. Latency=64. Min Gnt=8.Max Lat=56. Non-prefetchable 32 bit memory at 0xc4fff000 [0xc4ffffff]. I/O at 0x2400 [0x243f]. Non-prefetchable 32 bit memory at 0xc4e00000 [0xc4efffff]. Bus 0, device 3, function 0: VGA compatible controller: ATI Technologies Inc 3D Rage IIC 215IIC [Mach64 GT IIC] (rev 122). Master Capable. Latency=64. Min Gnt=8. Prefetchable 32 bit memory at 0xc3000000 [0xc3ffffff]. I/O at 0x2800 [0x28ff]. Non-prefetchable 32 bit memory at 0xc4dff000 [0xc4dfffff]. Bus 0, device 4, function 0: System peripheral: Compaq Computer Corporation Advanced System Management Controller (rev 0). I/O at 0x1800 [0x18ff]. Non-prefetchable 32 bit memory at 0xc4dfef00 [0xc4dfefff]. Bus 0, device 15, function 0: ISA bridge: ServerWorks OSB4 South Bridge (rev 79). Bus 0, device 15, function 1: IDE interface: ServerWorks OSB4 IDE Controller (rev 0). Master Capable. Latency=64. I/O at 0x2c00 [0x2c0f]. estaterlx:~# lspci -vv 00:00.0 Host bridge: ServerWorks CNB20LE Host Bridge (rev 05) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 64, cache line size 08 00:00.1 Host bridge: ServerWorks CNB20LE Host Bridge (rev 05) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64, cache line size 08 00:01.0 RAID bus controller: LSI Logic / Symbios Logic (formerly NCR): Unknown device 0010 (rev 02) Subsystem: Compaq Computer Corporation: Unknown device 4040 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 192 (7500ns min, 2000ns max), cache line size 08 Interrupt: pin A routed to IRQ 19 Region 0: I/O ports at 2000 [size=256] Region 1: Memory at c6000000 (32-bit, non-prefetchable) [size=16M] Region 2: Memory at c5000000 (32-bit, non-prefetchable) [size=16M] Expansion ROM at <unassigned> [disabled] [size=512K] Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:02.0 Ethernet controller: Intel Corp. 82557 [Ethernet Pro 100] (rev 08) Subsystem: Compaq Computer Corporation: Unknown device b134 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (2000ns min, 14000ns max), cache line size 08 Interrupt: pin A routed to IRQ 17 Region 0: Memory at c4fff000 (32-bit, non-prefetchable) [size=4K] Region 1: I/O ports at 2400 [size=64] Region 2: Memory at c4e00000 (32-bit, non-prefetchable) [size=1M] Expansion ROM at <unassigned> [disabled] [size=1M] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=2 PME- 00:03.0 VGA compatible controller: ATI Technologies Inc 3D Rage IIC 215IIC [Mach64 GT IIC] (rev 7a) (prog-if 00 [VGA]) Subsystem: ATI Technologies Inc 3D Rage IIC 215IIC [Mach64 GT IIC] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (2000ns min), cache line size 08 Region 0: Memory at c3000000 (32-bit, prefetchable) [size=16M] Region 1: I/O ports at 2800 [size=256] Region 2: Memory at c4dff000 (32-bit, non-prefetchable) [size=4K] Expansion ROM at <unassigned> [disabled] [size=128K] Capabilities: [5c] Power Management version 1 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00:04.0 System peripheral: Compaq Computer Corporation Advanced System Management Controller Subsystem: Compaq Computer Corporation: Unknown device b0f3 Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin A routed to IRQ 0 Region 0: I/O ports at 1800 [size=256] Region 1: Memory at c4dfef00 (32-bit, non-prefetchable) [size=256] 00:0f.0 ISA bridge: ServerWorks OSB4 South Bridge (rev 4f) Subsystem: ServerWorks OSB4 South Bridge Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 00:0f.1 IDE interface: ServerWorks OSB4 IDE Controller (prog-if 8a [Master SecP PriP]) Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 Region 4: I/O ports at 2c00 [size=16] estaterlx:~# cat /proc/scsi/ cat: /proc/scsi/: Is a directory estaterlx:~# cat /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 00 Lun: 00 Vendor: Linux Model: scsi_debug Rev: 0002 Type: Direct-Access ANSI SCSI revision: 02 estaterlx:~# dmesg Linux version 2.4.18-686-smp ([EMAIL PROTECTED]) (gcc version 2.95.4 20011002 (Debian prerelease)) #1 SMP Sun Apr 14 12:07:19 EST 2002 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f800 (usable) BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 0000000027ffc000 (usable) BIOS-e820: 0000000027ffc000 - 0000000028000000 (ACPI data) BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved) BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) found SMP MP-table at 000f4ff0 hm, page 000f4000 reserved twice. hm, page 000f5000 reserved twice. hm, page 000f2000 reserved twice. hm, page 000f3000 reserved twice. On node 0 totalpages: 163836 zone(0): 4096 pages. zone(1): 159740 pages. zone(2): 0 pages. Intel MultiProcessor Specification v1.4 Virtual Wire compatibility mode. OEM ID: COMPAQ Product ID: PROLIANT APIC at: 0xFEE00000 Processor #1 Pentium(tm) Pro APIC version 16 Processor #0 Pentium(tm) Pro APIC version 16 I/O APIC #8 Version 17 at 0xFEC00000. Processors: 2 Kernel command line: auto BOOT_IMAGE=Linux ro root=4803 Initializing CPU#0 Detected 731.081 MHz processor. Console: colour VGA+ 80x25 Calibrating delay loop... 1458.17 BogoMIPS Memory: 640220k/655344k available (900k kernel code, 14736k reserved, 250k data, 216k init, 0k highmem) Dentry-cache hash table entries: 131072 (order: 8, 1048576 bytes) Inode-cache hash table entries: 65536 (order: 7, 524288 bytes) Mount-cache hash table entries: 16384 (order: 5, 131072 bytes) Buffer-cache hash table entries: 65536 (order: 6, 262144 bytes) Page-cache hash table entries: 262144 (order: 8, 1048576 bytes) CPU: Before vendor init, caps: 0383fbff 00000000 00000000, vendor = 0 CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 256K CPU: After vendor init, caps: 0383fbff 00000000 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: After generic, caps: 0383fbff 00000000 00000000 00000000 CPU: Common caps: 0383fbff 00000000 00000000 00000000 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX mtrr: v1.40 (20010327) Richard Gooch ([EMAIL PROTECTED]) mtrr: detected mtrr type: Intel CPU: Before vendor init, caps: 0383fbff 00000000 00000000, vendor = 0 CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 256K CPU: After vendor init, caps: 0383fbff 00000000 00000000 00000000 Intel machine check reporting enabled on CPU#0. CPU: After generic, caps: 0383fbff 00000000 00000000 00000000 CPU: Common caps: 0383fbff 00000000 00000000 00000000 CPU0: Intel Pentium III (Coppermine) stepping 03 per-CPU timeslice cutoff: 730.53 usecs. enabled ExtINT on CPU#0 ESR value before enabling vector: 00000000 ESR value after enabling vector: 00000000 Booting processor 1/0 eip 2000 Initializing CPU#1 masked ExtINT on CPU#1 ESR value before enabling vector: 00000000 ESR value after enabling vector: 00000000 Calibrating delay loop... 1461.45 BogoMIPS CPU: Before vendor init, caps: 0383fbff 00000000 00000000, vendor = 0 CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 256K CPU: After vendor init, caps: 0383fbff 00000000 00000000 00000000 Intel machine check reporting enabled on CPU#1. CPU: After generic, caps: 0383fbff 00000000 00000000 00000000 CPU: Common caps: 0383fbff 00000000 00000000 00000000 CPU1: Intel Pentium III (Coppermine) stepping 03 Total of 2 processors activated (2919.62 BogoMIPS). ENABLING IO-APIC IRQs Setting 8 in the phys_id_present_map ...changing IO-APIC physical APIC ID to 8 ... ok. init IO_APIC IRQs IO-APIC (apicid-pin) 8-0, 8-5, 8-10, 8-16, 8-32, 8-33, 8-34 not connected. ..TIMER: vector=0x31 pin1=2 pin2=0 ..MP-BIOS bug: 8254 timer not connected to IO-APIC ...trying to set up timer (IRQ0) through the 8259A ... ..... (found pin 0) ...works. number of MP IRQ sources: 41. number of IO-APIC #8 registers: 35. testing the IO APIC....................... IO APIC #8...... .... register #00: 08000000 ....... : physical APIC id: 08 .... register #01: 00220011 ....... : max redirection entries: 0022 ....... : PRQ implemented: 0 ....... : IO APIC version: 0011 .... register #02: 00000000 ....... : arbitration: 00 .... IRQ redirection table: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: 00 003 03 0 0 0 0 0 1 1 31 01 003 03 0 0 0 0 0 1 1 39 02 000 00 1 0 0 0 0 0 0 00 03 003 03 0 0 0 0 0 1 1 41 04 003 03 0 0 0 0 0 1 1 49 05 000 00 1 0 0 0 0 0 0 00 06 003 03 0 0 0 0 0 1 1 51 07 003 03 1 1 0 1 0 1 1 59 08 003 03 0 0 0 0 0 1 1 61 09 003 03 0 0 0 0 0 1 1 69 0a 000 00 1 0 0 0 0 0 0 00 0b 003 03 0 0 0 0 0 1 1 71 0c 003 03 0 0 0 0 0 1 1 79 0d 003 03 1 1 0 1 0 1 1 81 0e 003 03 0 0 0 0 0 1 1 89 0f 003 03 0 0 0 0 0 1 1 91 10 000 00 1 0 0 0 0 0 0 00 11 003 03 1 1 0 1 0 1 1 99 12 003 03 1 1 0 1 0 1 1 A1 13 003 03 1 1 0 1 0 1 1 A9 14 003 03 1 1 0 1 0 1 1 B1 15 003 03 1 1 0 1 0 1 1 B9 16 003 03 1 1 0 1 0 1 1 C1 17 003 03 1 1 0 1 0 1 1 C9 18 003 03 1 1 0 1 0 1 1 D1 19 003 03 1 1 0 1 0 1 1 D9 1a 003 03 1 1 0 1 0 1 1 E1 1b 003 03 1 1 0 1 0 1 1 E9 1c 003 03 1 1 0 1 0 1 1 32 1d 003 03 1 1 0 1 0 1 1 3A 1e 003 03 1 1 0 1 0 1 1 42 1f 003 03 1 1 0 1 0 1 1 4A 20 000 00 1 0 0 0 0 0 0 00 21 000 00 1 0 0 0 0 0 0 00 22 000 00 1 0 0 0 0 0 0 00 IRQ to pin mappings: IRQ0 -> 0:2 IRQ1 -> 0:1 IRQ3 -> 0:3 IRQ4 -> 0:4 IRQ6 -> 0:6 IRQ7 -> 0:7 IRQ8 -> 0:8 IRQ9 -> 0:9 IRQ11 -> 0:11 IRQ12 -> 0:12 IRQ13 -> 0:13 IRQ14 -> 0:14 IRQ15 -> 0:15 IRQ17 -> 0:17 IRQ18 -> 0:18 IRQ19 -> 0:19 IRQ20 -> 0:20 IRQ21 -> 0:21 IRQ22 -> 0:22 IRQ23 -> 0:23 IRQ24 -> 0:24 IRQ25 -> 0:25 IRQ26 -> 0:26 IRQ27 -> 0:27 IRQ28 -> 0:28 IRQ29 -> 0:29 IRQ30 -> 0:30 IRQ31 -> 0:31 .................................... done. Using local APIC timer interrupts. calibrating APIC timer ... ..... CPU clock speed is 731.0436 MHz. ..... host bus clock speed is 132.9168 MHz. cpu: 0, clocks: 1329168, slice: 443056 CPU0<T0:1329168,T1:886112,D:0,S:443056,C:1329168> cpu: 1, clocks: 1329168, slice: 443056 CPU1<T0:1329168,T1:443056,D:0,S:443056,C:1329168> checking TSC synchronization across CPUs: passed. Waiting on wait_init_idle (map = 0x2) All processors have done init_idle mtrr: your CPUs had inconsistent fixed MTRR settings mtrr: probably your BIOS does not setup all CPUs PCI: PCI BIOS revision 2.10 entry at 0xf0084, last bus=3 PCI: Using configuration type 1 PCI: Probing PCI hardware PCI->APIC IRQ transform: (B0,I1,P0) -> 19 PCI->APIC IRQ transform: (B0,I2,P0) -> 17 PCI: Device 00:00 not found by BIOS PCI: Device 00:01 not found by BIOS PCI: Device 00:78 not found by BIOS Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd VFS: Diskquotas version dquot_6.4.0 initialized devfs: v1.10 (20020120) Richard Gooch ([EMAIL PROTECTED]) devfs: boot_options: 0x0 pty: 256 Unix98 ptys configured Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI enabled ttyS00 at 0x03f8 (irq = 4) is a 16550A ttyS01 at 0x02f8 (irq = 3) is a 16550A block: 128 slots per queue, batch=32 RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize Cronyx Ltd, Synchronous PPP and CISCO HDLC (c) 1994 Linux port (c) 1998 Building Number Three Ltd & Jan "Yenya" Kasprzak. NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 8192 buckets, 64Kbytes TCP: Hash tables configured (established 262144 bind 65536) Linux IP multicast router 0.06 plus PIM-SM RAMDISK: cramfs filesystem found at block 0 RAMDISK: Loading 2668 blocks [1 disk] into ram disk... done. Freeing initrd memory: 2668k freed VFS: Mounted root (cramfs filesystem). Freeing unused kernel memory: 216k freed NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. cpqarray: Device 0x1000 has been found at bus 0 dev 1 func 0 Compaq SMART2 Driver (v 2.4.5) Found 1 controller(s) cpqarray: Finding drives on ida0 (Integrated Array) cpqarray ida/c0d0: blksz=512 nr_blks=17756160 cpqarray: Starting firmware's background processing Partition check: /dev/ida/c0d0: p1 p2 p3 p4 Journalled Block Device driver loaded kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. Adding Swap: 999592k swap-space (priority -1) EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ida0(72,3), internal journal Real Time Clock Driver v1.10e eepro100.c:v1.09j-t 9/29/99 Donald Becker http://www.scyld.com/network/eepro100.html eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin <[EMAIL PROTECTED]> and others eth0: OEM i82557/i82558 10/100 Ethernet, 00:50:8B:DE:83:83, IRQ 17. Board assembly 010101-034, Physical connectors present: RJ45 Primary interface chip i82555 PHY #1. General self-test: passed. Serial sub-system self-test: passed. Internal registers self-test: passed. ROM checksum self-test: passed (0x04f4518b). SCSI subsystem driver Revision: 1.00 scsi0 : scsi_debug, Version: 0.57 (20011209), num_devs=1, dev_size_mb=8 Vendor: Linux Model: scsi_debug Rev: 0002 Type: Direct-Access ANSI SCSI revision: 02 device eth0 entered promiscuous mode mtrr: Serverworks LE detected. Write-combining disabled. mtrr: your processor doesn't support write-combining mtrr: Serverworks LE detected. Write-combining disabled. mtrr: your processor doesn't support write-combining osst :I: Unloaded. --- Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com). Version: 6.0.449 / Virus Database: 251 - Release Date: 27/1/2003 -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
