Respondendo:
1. Sim, consigo acessar sites normalmente, inclusive o google talk conecta 2. Sim, é usado senha padrão WPA-PSK. T+++, José Roberto. 2011/1/26 Rodolfo <rof20...@gmail.com> > Boa noite josé. Tenho umas perguntas: > > 1 - Você conectado na wireless somente, dá esse problema no MSN ? Mas dá > pra acessar algum site ou não ? > > 2 - Esse seu AP, precisa de senha para conectar nele ? > > > Flw =D > > 2011/1/26 José Roberto <zep...@gmail.com> > > Boa noite pessoal, >> >> Tenho um note Aspire 5251-1096, placa rede wireless está usando o driver >> ath9k, placa de rede convecional está usando driver tg3, minhas placas no >> lspci: >> >> >> 02:00.0 Ethernet controller: Broadcom Corporation NetLink BCM57780 Gigabit >> Ethernet PCIe (rev 01) >> 08:00.0 Network controller: Atheros Communications Inc. AR928X Wireless >> Network Adapter (PCI-Express) (rev 01) >> >> Os dados do dmesg: >> >> Wlan0 >> >> root@jose:~# dmesg | grep wlan >> [ 13.527224] ADDRCONF(NETDEV_UP): wlan0: link is not ready >> [ 49.204349] wlan0: direct probe to AP 00:21:91:6f:40:aa (try 1) >> [ 49.207399] wlan0: direct probe responded >> [ 49.207404] wlan0: authenticate with AP 00:21:91:6f:40:aa (try 1) >> [ 49.209626] wlan0: authenticated >> [ 49.209649] wlan0: associate with AP 00:21:91:6f:40:aa (try 1) >> [ 49.212359] wlan0: RX AssocResp from 00:21:91:6f:40:aa (capab=0x431 >> status=0 aid=1) >> [ 49.212362] wlan0: associated >> [ 49.212725] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready >> [ 59.468137] wlan0: no IPv6 routers present >> root@jose:~# >> >> Eth0 >> >> root@jose:~# dmesg | grep eth >> [ 1.467096] eth0: Tigon3 [partno(BCM57780) rev 57780001] (PCI Express) >> MAC address 00:23:5a:64:43:20 >> [ 1.467100] eth0: attached PHY driver [Broadcom BCM57780] >> (mii_bus:phy_addr=200:01) >> [ 1.467103] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1] >> [ 1.467105] eth0: dma_rwctrl[76180000] dma_mask[64-bit] >> [ 13.317616] ADDRCONF(NETDEV_UP): eth0: link is not ready >> [ 14.177135] tg3: eth0: Link is down. >> root@jose:~# >> >> Os dados do comando usando iwconfig conectado: >> wlan0 IEEE 802.11bgn ESSID:"Leonor" >> Mode:Managed Frequency:2.437 GHz Access Point: >> 00:21:91:6F:40:AA >> Bit Rate=54 Mb/s Tx-Power=20 dBm >> Retry long limit:7 RTS thr:off Fragment thr:off >> Encryption key:off >> Power Management:on >> Link Quality=52/70 Signal level=-58 dBm >> Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 >> Tx excessive retries:0 Invalid misc:0 Missed beacon:0 >> >> O que está muito estranho que conectado a placa de rede normal conecta no >> msn usando o Empathy com telepathy-haze, porém quando eu uso rede wireless >> não consegue conectar, já tentei usando o telepathy-butterfly, mas acontece >> o mesmo erro, se precisarem de mais alguma informa para tentarem ajudar, só >> avisar, de preferência com os comandos. > > >
