Bonjour,
Le 12/06/2014 18:31, daniel huhardeaux a écrit :
Combien de disques y a t'il dans le serveur?
Il y a toujours les 5 disques
root@serre:~# fdisk -l
Disk /dev/sda: 120.0 GB, 120034123776 bytes
[...]
Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes
[...]
Disk /dev/sdc: 1000.2 GB, 1000204886016 bytes
[...]
Disk /dev/md0: 2000.1 GB, 2000138797056 bytes
[...]
Disk /dev/sdd: 1000.2 GB, 1000204886016 bytes
[...]
Disk /dev/sde: 1000.2 GB, 1000204886016 bytes
[...]
mdadm.conf est il toujours
bon ?
Oui les modifs effectuées sont toujours présentes.
Le renommage des disques ne se fait pas seul, un coup d'oeil dans
dmesg devrait apporter des informations
C'est sûrement ce que je me suis dit également, les disques semblent
changer de nommage au boot.
Voilà ce que me dit dmesg, je ne suis pas un expert, j'ai extrait les
lignes correspondant au montage des disques et du RAID.
Ce que je comprend c'est que les disques HGST sont connectés en SATA et
que les disques WD sont connectés en SCSI.
Le raid essaie de monter les disques et n'y arrive pas car les disques
SCSI ne sont pas encore montés ?
Vous comprenez ça comme moi ?
root@serre:~# dmesg
[ 1.744044] ata6: SATA link down (SStatus 0 SControl 300)
[ 1.744064] ata5: SATA link down (SStatus 0 SControl 300)
[ 1.744084] ata1: SATA link down (SStatus 0 SControl 300)
[ 1.744106] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 1.744128] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.744145] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.744917] ata2.00: ATA-9: Samsung SSD 840 Series, DXT08B0Q, max
UDMA/133
[ 1.744933] ata2.00: 234441648 sectors, multi 16: LBA48 NCQ (depth
31/32), AA
[ 1.745196] ata2.00: configured for UDMA/133
[ 1.745263] scsi: waiting for bus probes to complete ...
[ 1.745315] ata4.00: ATA-8: HGST HTS721010A9E630, JB0OA3B0, max UDMA/133
[ 1.745319] ata4.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth
31/32), AA
[ 1.745418] ata3.00: ATA-8: HGST HTS721010A9E630, JB0OA3B0, max UDMA/133
[ 1.745438] ata3.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth
31/32), AA
[ 1.746777] ata4.00: configured for UDMA/133
[ 1.746949] ata3.00: configured for UDMA/133
[ 1.756012] usb 1-1: new high-speed USB device number 2 using ehci_hcd
[ 1.792161] scsi 2:0:0:0: Direct-Access ATA Samsung SSD 840
DXT0 PQ: 0 ANSI: 5
[ 1.792557] scsi 3:0:0:0: Direct-Access ATA HGST HTS721010A9
JB0O PQ: 0 ANSI: 5
[ 1.792909] scsi 4:0:0:0: Direct-Access ATA HGST HTS721010A9
JB0O PQ: 0 ANSI: 5
[ 1.797059] sd 2:0:0:0: [sda] 234441648 512-byte logical blocks: (120
GB/111 GiB)
[ 1.797087] sd 3:0:0:0: [sdb] 1953525168 512-byte logical blocks:
(1.00 TB/931 GiB)
[ 1.797090] sd 3:0:0:0: [sdb] 4096-byte physical blocks
[ 1.797126] sd 4:0:0:0: [sdc] 1953525168 512-byte logical blocks:
(1.00 TB/931 GiB)
[ 1.797128] sd 4:0:0:0: [sdc] 4096-byte physical blocks
[ 1.797146] sd 3:0:0:0: [sdb] Write Protect is off
[ 1.797150] sd 2:0:0:0: [sda] Write Protect is off
[ 1.797153] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.797156] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1.797171] sd 2:0:0:0: [sda] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 1.797174] sd 3:0:0:0: [sdb] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 1.797178] sd 4:0:0:0: [sdc] Write Protect is off
[ 1.797181] sd 4:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 1.797198] sd 4:0:0:0: [sdc] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 1.797902] sda: sda1 sda2 < sda5 >
[ 1.798244] sd 2:0:0:0: [sda] Attached SCSI disk
[ 1.813472] sd 2:0:0:0: Attached scsi generic sg0 type 0
[ 1.813522] sd 3:0:0:0: Attached scsi generic sg1 type 0
[ 1.813568] sd 4:0:0:0: Attached scsi generic sg2 type 0
[...]
[ 2.057259] sdc: sdc1
[ 2.057857] sd 4:0:0:0: [sdc] Attached SCSI disk
[ 2.067727] sdb: sdb1
[ 2.068379] sd 3:0:0:0: [sdb] Attached SCSI disk
[...]
[ 2.427055] md: md0 stopped.
[ 2.427583] md: bind<sdc1>
[ 2.427731] md: bind<sdb1>
[ 2.428796] md: raid10 personality registered for level 10
[ 2.428997] bio: create slab <bio-1> at 1
[ 2.429065] md/raid10:md0: active with 2 out of 4 devices
[ 2.429084] md0: detected capacity change from 0 to 2000138797056
[ 2.434495] md0: unknown partition table
[...]
[ 4.529901] sas: phy-0:0 added to port-0:0, phy_mask:0x1
(5fcfffff00000001)
[ 4.529912] sas: DOING DISCOVERY on port 0, pid:227
[ 4.546219] EXT4-fs (md0): mounted filesystem with ordered data mode.
Opts: (null)
[ 4.714535] sas: Enter sas_scsi_recover_host
[ 4.714544] ata7: sas eh calling libata port error handler
[ 4.714557] sas: sas_ata_hard_reset: Found ATA device.
[ 4.715195] ata7.00: ATA-9: WDC WD10JPVX-08JC3T2, 03.01A03, max UDMA/133
[ 4.715202] ata7.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 4.715918] ata7.00: configured for UDMA/133
[ 4.715929] sas: --- Exit sas_scsi_recover_host
[ 4.729225] scsi 0:0:0:0: Direct-Access ATA WDC WD10JPVX-08J
03.0 PQ: 0 ANSI: 5
[ 4.729530] sd 0:0:0:0: Attached scsi generic sg3 type 0
[ 4.729544] sd 0:0:0:0: [sdd] 1953525168 512-byte logical blocks:
(1.00 TB/931 GiB)
[ 4.729550] sd 0:0:0:0: [sdd] 4096-byte physical blocks
[ 4.729600] sas: DONE DISCOVERY on port 0, pid:227, result:0
[ 4.729722] sd 0:0:0:0: [sdd] Write Protect is off
[ 4.729731] sd 0:0:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 4.729791] sd 0:0:0:0: [sdd] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 4.754634] sdd: sdd1
[ 4.755223] sd 0:0:0:0: [sdd] Attached SCSI disk
[ 4.947395] sas: phy-0:1 added to port-0:1, phy_mask:0x2
(5fcfffff00000002)
[ 4.947414] sas: DOING DISCOVERY on port 1, pid:226
[ 5.136103] sas: Enter sas_scsi_recover_host
[ 5.136111] ata7: sas eh calling libata port error handler
[ 5.136126] ata8: sas eh calling libata port error handler
[ 5.136135] sas: sas_ata_hard_reset: Found ATA device.
[ 5.136771] ata8.00: ATA-9: WDC WD10JPVX-08JC3T2, 03.01A03, max UDMA/133
[ 5.136777] ata8.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 5.137630] ata8.00: configured for UDMA/133
[ 5.137642] sas: --- Exit sas_scsi_recover_host
[ 5.137865] scsi 0:0:1:0: Direct-Access ATA WDC WD10JPVX-08J
03.0 PQ: 0 ANSI: 5
[ 5.138096] sd 0:0:1:0: [sde] 1953525168 512-byte logical blocks:
(1.00 TB/931 GiB)
[ 5.138100] sd 0:0:1:0: [sde] 4096-byte physical blocks
[ 5.138159] sd 0:0:1:0: Attached scsi generic sg4 type 0
[ 5.138189] sd 0:0:1:0: [sde] Write Protect is off
[ 5.138193] sd 0:0:1:0: [sde] Mode Sense: 00 3a 00 00
[ 5.138223] sd 0:0:1:0: [sde] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 5.138287] sas: DONE DISCOVERY on port 1, pid:226, result:0
[ 5.161051] sde: sde1
[ 5.161803] sd 0:0:1:0: [sde] Attached SCSI disk
Soit je dois les ajouter après au raid ?
Pourquoi les disques changent de label ?
Grégoire
--
Lisez la FAQ de la liste avant de poser une question :
http://wiki.debian.org/fr/FrenchLists
Pour vous DESABONNER, envoyez un message avec comme objet "unsubscribe"
vers debian-user-french-requ...@lists.debian.org
En cas de soucis, contactez EN ANGLAIS listmas...@lists.debian.org
Archive: https://lists.debian.org/539ac711.7060...@gmail.com
