> Bonjour à nouveau, Salut, > Voici aprés redémarrage ce que me renvoie dmesg : > > Y voyez vous quelquechose.
on va voir plus bas. > En dernier recours, il ne me reste plus qu'a ré-installer toute la machine. Ce serait dommage, mais si ça fait gagner du temps, pourquoi pas ... > > ACPI: PCI Root Bridge [PCI0] (0000:00) > PCI: Probing PCI hardware (bus 00) > ACPI: Assume root bridge [\_SB_.PCI0] bus is 0 > PCI quirk: region 0900-097f claimed by ICH4 ACPI/GPIO/TCO > PCI quirk: region 0800-083f claimed by ICH4 GPIO > PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1 > PCI: PXH quirk detected, disabling MSI for SHPC device > PCI: PXH quirk detected, disabling MSI for SHPC device > PCI: Transparent bridge - 0000:00:1e.0 > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.IP2P._PRT] > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.ICHR._PRT] > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PTB0._PRT] > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PTB0.PCXA._PRT] > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PTB0.PCXB._PRT] > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PTA0._PRT] > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PTC0._PRT] > ACPI: PCI Interrupt Link [LNKA] (IRQs *5 7 10 11) > ACPI: PCI Interrupt Link [LNKB] (IRQs 5 7 10 11) *0, disabled. > ACPI: PCI Interrupt Link [LNKC] (IRQs 5 *7 10 11) > ACPI: PCI Interrupt Link [LNKD] (IRQs *5 7 10 11) > ACPI: PCI Interrupt Link [LNKE] (IRQs 5 7 10 11) *0, disabled. > ACPI: PCI Interrupt Link [LNKF] (IRQs *5 7 10 11) > ACPI: PCI Interrupt Link [LNKG] (IRQs *5 7 10 11) > ACPI: PCI Interrupt Link [LNKH] (IRQs *5 7 10 11) > Linux Plug and Play Support v0.97 (c) Adam Belay > pnp: PnP ACPI init > pnp: PnP ACPI: found 9 devices > PnPBIOS: Disabled by ACPI PNP > PCI: Using ACPI for IRQ routing > PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a > report > PCI: Cannot allocate resource region 4 of device 0000:00:1d.0 > PCI: Cannot allocate resource region 4 of device 0000:00:1d.1 > PCI: Cannot allocate resource region 0 of device 0000:00:1f.2 > PCI: Cannot allocate resource region 1 of device 0000:00:1f.2 > PCI: Cannot allocate resource region 2 of device 0000:00:1f.2 > PCI: Cannot allocate resource region 3 of device 0000:00:1f.2 > PCI: Cannot allocate resource region 4 of device 0000:00:1f.2 > PCI: Device 0000:00:00.0 not found by BIOS > pnp: 00:01: ioport range 0x408-0x40f has been reserved > pnp: 00:01: ioport range 0x4d0-0x4d1 has been reserved > pnp: 00:01: ioport range 0x700-0x71f has been reserved > PCI: Bridge: 0000:00:02.0 > IO window: disabled. > MEM window: disabled. > PREFETCH window: disabled. > PCI: Bridge: 0000:06:00.0 > IO window: disabled. > MEM window: disabled. > PREFETCH window: disabled. > PCI: Bridge: 0000:06:00.2 > IO window: disabled. > MEM window: disabled. > PREFETCH window: disabled. > PCI: Bridge: 0000:00:04.0 > IO window: disabled. > MEM window: disabled. > PREFETCH window: disabled. > PCI: Bridge: 0000:00:06.0 > IO window: disabled. > MEM window: disabled. > PREFETCH window: disabled. > PCI: Bridge: 0000:00:1c.0 > IO window: disabled. > MEM window: fdf00000-fdffffff > PREFETCH window: disabled. > PCI: Bridge: 0000:00:1e.0 > IO window: 1000-3fff > MEM window: fbf00000-fcffffff > PREFETCH window: 50000000-500fffff > ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 169 > PCI: Setting latency timer of device 0000:00:02.0 to 64 > ACPI: PCI Interrupt 0000:00:04.0[A] -> GSI 16 (level, low) -> IRQ 169 > PCI: Setting latency timer of device 0000:00:04.0 to 64 > PCI: Setting latency timer of device 0000:06:00.0 to 64 > PCI: Setting latency timer of device 0000:06:00.2 to 64 > ACPI: PCI Interrupt 0000:00:06.0[A] -> GSI 16 (level, low) -> IRQ 169 > PCI: Setting latency timer of device 0000:00:06.0 to 64 > PCI: Setting latency timer of device 0000:00:1e.0 to 64 > NET: Registered protocol family 2 > IP route cache hash table entries: 32768 (order: 5, 131072 bytes) > TCP established hash table entries: 131072 (order: 8, 1048576 bytes) > TCP bind hash table entries: 65536 (order: 7, 524288 bytes) > TCP: Hash tables configured (established 131072 bind 65536) > TCP reno registered > audit: initializing netlink socket (disabled) > audit(1234246311.284:1): initialized > highmem bounce pool size: 64 pages > VFS: Disk quotas dquot_6.5.1 > Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) > Initializing Cryptographic API > io scheduler noop registered > io scheduler anticipatory registered > io scheduler deadline registered > io scheduler cfq registered (default) > PCI: Setting latency timer of device 0000:00:02.0 to 64 > Allocate Port Service[0000:00:02.0:pcie00] > PCI: Setting latency timer of device 0000:00:04.0 to 64 > Allocate Port Service[0000:00:04.0:pcie00] > PCI: Setting latency timer of device 0000:00:06.0 to 64 > Allocate Port Service[0000:00:06.0:pcie00] > isapnp: Scanning for PnP cards... > isapnp: No Plug & Play device found > Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled > serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A > serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A > 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A > RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize > PNP: PS/2 Controller [PNP0303:KBD,PNP0f0e:PS2M] at 0x60,0x64 irq 1,12 > serio: i8042 AUX port at 0x60,0x64 irq 12 > serio: i8042 KBD port at 0x60,0x64 irq 1 > mice: PS/2 mouse device common for all mice > TCP bic registered > NET: Registered protocol family 1 > NET: Registered protocol family 17 > NET: Registered protocol family 8 > NET: Registered protocol family 20 > Starting balanced_irq > Using IPI No-Shortcut mode > ACPI: (supports S0 S4 S5) > Freeing unused kernel memory: 196k freed > Time: tsc clocksource has been installed. > input: AT Translated Set 2 keyboard as /class/input/input0 > ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not > present [20060707] > ACPI: Getting cpuindex for acpiid 0x2 > ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not > present [20060707] > ACPI: Getting cpuindex for acpiid 0x3 > ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not > present [20060707] > ACPI: Getting cpuindex for acpiid 0x4 > ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not > present [20060707] > ACPI: Getting cpuindex for acpiid 0x5 > ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not > present [20060707] > ACPI: Getting cpuindex for acpiid 0x6 > ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not > present [20060707] > ACPI: Getting cpuindex for acpiid 0x7 > ACPI: Thermal Zone [THM0] (8 C) > usbcore: registered new driver usbfs > usbcore: registered new driver hub > tg3.c:v3.65 (August 07, 2006) > ACPI: PCI Interrupt 0000:02:02.0[A] -> GSI 25 (level, low) -> IRQ 177 > Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 > ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx > eth0: Tigon3 [partno(349321-001) rev 2100 PHY(5704)] (PCIX:66MHz:64-bit) > 10/100/1000BaseT Ethernet 00:15:60:aa:cc:ba > eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] Split[0] WireSpeed[1] > TSOcap[0] > eth0: dma_rwctrl[769f0000] dma_mask[64-bit] > ACPI: PCI Interrupt 0000:02:02.1[B] -> GSI 26 (level, low) -> IRQ 185 > eth1: Tigon3 [partno(349321-001) rev 2100 PHY(5704)] (PCIX:66MHz:64-bit) > 10/100/1000BaseT Ethernet 00:15:60:aa:cc:b9 > eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] > TSOcap[1] > eth1: dma_rwctrl[769f0000] dma_mask[64-bit] > SCSI subsystem initialized > USB Universal Host Controller Interface driver v3.0 > ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 169 > PCI: Setting latency timer of device 0000:00:1d.0 to 64 > uhci_hcd 0000:00:1d.0: UHCI Host Controller > uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 > uhci_hcd 0000:00:1d.0: irq 169, io base 0x00004000 > usb usb1: configuration #1 chosen from 1 choice > hub 1-0:1.0: USB hub found > hub 1-0:1.0: 2 ports detected > libata version 2.00 loaded. > ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 193 > PCI: Setting latency timer of device 0000:00:1d.1 to 64 > uhci_hcd 0000:00:1d.1: UHCI Host Controller > uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 > uhci_hcd 0000:00:1d.1: irq 193, io base 0x00004020 > usb usb2: configuration #1 chosen from 1 choice > hub 2-0:1.0: USB hub found > hub 2-0:1.0: 2 ports detected > ICH5: IDE controller at PCI slot 0000:00:1f.1 > PCI: Enabling device 0000:00:1f.1 (0005 -> 0007) > ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 201 > ICH5: chipset revision 2 > ICH5: not 100% native mode: will probe irqs later > ide0: BM-DMA at 0x0500-0x0507, BIOS settings: hda:DMA, hdb:pio > ide1: BM-DMA at 0x0508-0x050f, BIOS settings: hdc:pio, hdd:pio > Probing IDE interface ide0... > hda: DV-28E-N, ATAPI CD/DVD-ROM drive > ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 > Probing IDE interface ide1... > ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 209 > PCI: Setting latency timer of device 0000:00:1d.7 to 64 > ehci_hcd 0000:00:1d.7: EHCI Host Controller > ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 3 > ehci_hcd 0000:00:1d.7: debug port 1 > PCI: cache line size of 128 is not supported by device 0000:00:1d.7 > ehci_hcd 0000:00:1d.7: irq 209, io mem 0xfbee0000 > ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 > usb usb3: configuration #1 chosen from 1 choice > hub 3-0:1.0: USB hub found > hub 3-0:1.0: 4 ports detected > hda: ATAPI 24X DVD-ROM drive, 256kB Cache, UDMA(33) > Uniform CD-ROM driver Revision: 3.20 > ata_piix 0000:00:1f.2: version 2.00 > ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ] > ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 201 > PCI: Setting latency timer of device 0000:00:1f.2 to 64 > ata1: SATA max UDMA/133 cmd 0x4050 ctl 0x4062 bmdma 0x4040 irq 201 > ata2: SATA max UDMA/133 cmd 0x4058 ctl 0x4066 bmdma 0x4048 irq 201 > scsi0 : ata_piix > ATA: abnormal status 0x7F on port 0x4057 > scsi1 : ata_piix > ata2.00: ATA-7, max UDMA/100, 156301488 sectors: LBA48 > ata2.00: ata2: dev 0 multi count 8 > ata2.00: configured for UDMA/100 > Vendor: ATA Model: FB080C4080 Rev: n/a > Type: Direct-Access ANSI SCSI revision: 05 > SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB) > sda: Write Protect is off > sda: Mode Sense: 00 3a 00 00 > SCSI device sda: drive cache: write through > SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB) > sda: Write Protect is off > sda: Mode Sense: 00 3a 00 00 > SCSI device sda: drive cache: write through > sda: sda1 sda2 < sda5 > > sd 1:0:0:0: Attached scsi disk sda > Attempting manual resume > EXT3-fs: INFO: recovery required on readonly filesystem. > EXT3-fs: write access will be enabled during recovery. > kjournald starting. Commit interval 5 seconds > EXT3-fs: sda1: orphan cleanup on readonly fs > ext3_orphan_cleanup: deleting unreferenced inode 7962921 > ext3_orphan_cleanup: deleting unreferenced inode 6094856 > ext3_orphan_cleanup: deleting unreferenced inode 6094855 > ext3_orphan_cleanup: deleting unreferenced inode 6094854 > ext3_orphan_cleanup: deleting unreferenced inode 6094853 > ext3_orphan_cleanup: deleting unreferenced inode 6094852 > EXT3-fs: sda1: 6 orphan inodes deleted > EXT3-fs: recovery complete. > EXT3-fs: mounted filesystem with ordered data mode. > EDAC MC: Ver: 2.0.1 Dec 24 2007 > Contact your BIOS vendor to see if the E752x error registers can be safely > un-hidden > e752x_edac: probe of 0000:00:00.0 failed with error -12 > pci_hotplug: PCI Hot Plug PCI Core version: 0.5 > shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 > Floppy drive(s): fd0 is 1.44M > FDC 0 is a National Semiconductor PC87306 > input: PC Speaker as /class/input/input1 > intel_rng: FWH not detected > input: PS/2 Generic Mouse as /class/input/input2 > ts: Compaq touchscreen protocol output > Adding 2650684k swap on /dev/sda5. Priority:-1 extents:1 across:2650684k > EXT3 FS on sda1, internal journal > loop: loaded (max 8 devices) > device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: > dm-de...@redhat.com > i8xx TCO timer: failed to reset NO_REBOOT flag, reboot disabled by hardware > PM: Writing back config space on device 0000:02:02.0 at offset b (was > 164814e4, writing d00e11) > PM: Writing back config space on device 0000:02:02.0 at offset 3 (was > 804000, writing 804010) > PM: Writing back config space on device 0000:02:02.0 at offset 2 (was > 2000000, writing 2000010) > PM: Writing back config space on device 0000:02:02.0 at offset 1 (was > 2b00000, writing 2b00146) > NET: Registered protocol family 10 > lo: Disabled Privacy Extensions > ADDRCONF(NETDEV_UP): eth0: link is not ready > IPv6 over IPv4 tunneling driver > tg3: eth0: Link is up at 1000 Mbps, full duplex. > tg3: eth0: Flow control is off for TX and off for RX. > ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready > ACPI: Power Button (FF) [PWRF] > eth0: no IPv6 routers present > Perso, je ne vois rien lié à ton problème. Peut-être d'autres verront quelque chose. Mais > > > > > > HPU1HD08:/var/log# cat /etc/fstab > > > # /etc/fstab: static file system information. > > > # > > > # <file system> <mount point> <type> <options> <dump> <pass> > > > proc /proc proc defaults 0 0 > > > /dev/sda1 / ext3 defaults,errors=remount-ro 0 > > 1 > > > > J'enlèverai 'errors=remount-ro' sur cette ligne et redémarrerai le > > système. Tu pourra toujours le remettre plus tard. As-tu essayé ceci ? -- Lisez la FAQ de la liste avant de poser une question : http://wiki.debian.org/DebFrFrenchLists Vous pouvez aussi ajouter le mot ``spam'' dans vos champs "From" et "Reply-To:" To UNSUBSCRIBE, email to debian-user-french-requ...@lists.debian.org with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
